This removes the need to set the MMC pins with pullups in our DTS.
Thanks to jmcneill@ for spotting this.
Tested on Orange Pi One (Allwinner H3).
MFC after: 1 week
GPIO_INPUT/GPIO_OUTPUT.
a10_gpio_get_pud now returns the whole pud not only PULLDOWN/PULLUP.
Add a10_gpio_get_drv to get the current drive strenght.
During fdt pin configure, avoid setting function/drive/pud if it's already in
the correct value.
Tested on Allwinner H3 and A20
MFC after: 1 week
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
will be needed when we bring in further support for these SoCs.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5340
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
pins, they specify the bank and the pin in two separated cells.
This allow the use of vendor's DTS definitions by adding a gpio map
routine that copes with that.
o Return the real hardware state in gpio_pin_getflags() instead of keep
the last state in an internal table. Now the driver returns the real
state of pins (input/output and pull-up/pull-down) at all times.
o Use a spin mutex. This is required by interrupts and the 1-wire code.
o Use better variable names and place parentheses around them in MACROS.
o Do not lock the driver when returning static data.
Tested with gpioled(4) and DS1820 (1-wire) sensors on banana pi.
change to GMAC easier on A20 SoCs.
On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).
On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.
There is work in progress to bring in GMAC support.
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
sys/arm and sys/mips), squelching the clang 3.3 warnings about this.
Noticed by: tinderbox and many irate spectators
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
PR: kern/177759
MFC after: 3 days
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
