Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Move <sys/conf.h> before <sys/disk.h>.
No need for raidread()/raidwrite(), we have generic code for that.
Remove non-functional dump code.
Make raidinit() return the softc, not the dev_t.
Move to "struct disk*" centric API.
Fix printfs' to get name from struct disk instead of dev_t.
OK'ed by: scottl
don't end up freezing the box. This makes VTY locking useless
in the DDB case but a box which is supposed to be physically
secure shouldn't compile DDB anyway.
Reviewed by: silence on -audit
Improve SBP device probeing:
- Wait 2 sec before issuing LOGIN ORB expecting the reconnection
hold timer expires.
- Serialize management ORB and scanning LUN by CAM on each target.
This should fix the problem for devices which have multiple LUNs.
Test device is donated by: Jaye Mathisen <mrcpu@internetcds.com>
- Freeze SIM queue for 2 sec after BUS RESET.
- Retry with LOGIN rather than RECONNECT after LOGIN is not completed for
BUS RESET.
- Use appropriate CAM status for BUS RESET and DEVICE RESET.
- Let CAM to scan targets after BUS REST.
- Implement CAM scan target function.
- Keep our own devq freeze count.
- Let CAM to know that SBP does tagged queuing.
These should be merged to RELENG_4 before 4.8-RELEASE.
a correctly aligned address in this block we really want to check, that the
part of the chunk that starts at the aligned address is large enough with
regard to the original request. Comparing it to 0 makes no sense, because this
is always true except in the rare case, that the aligned address is just at
the end of the chunk.
Approved by: jake (mentor)
the fxp driver. This is enabled only for the 82550/82551 chips
(PCI revision code 12 or 13). RX and TX checksum offload are
both supported. Transmit offload is limited to TCP and UDP only
right now: there seems to be a problem with IP header checksumming
on transmit in some cases.
This chip has hardware VLAN support as well. I hope to enable
support for this eventually.
- the mutex aac_io_lock protects the main codepaths which handle queues and
hardware registers. Only one acquire/release is done in the top-half and
the taskqueue. This mutex also applies to the userland command path and
CAM data path.
- Move the taskqueue to the new Giant-free version.
- Register the disk device with DISKFLAG_NOGIANT so the top-half processing
runs without Giant.
- Move the dynamic command allocator to the worker thread to avoid locking
issues with bus_dmamem_alloc().
This gives about 20% improvement in most of my benchmarks.
turns runs its tasks free of Giant too. It is intended that as drivers
become locked down, they will move out of the old, Giant-bound taskqueue
and into this new one. The old taskqueue has been renamed to
taskqueue_swi_giant, and the new one keeps the name taskqueue_swi.
- Remove the buftimelock mutex and acquire the buf's interlock to protect
these fields instead.
- Hold the vnode interlock while locking bufs on the clean/dirty queues.
This reduces some cases from one BUF_LOCK with a LK_NOWAIT and another
BUF_LOCK with a LK_TIMEFAIL to a single lock.
Reviewed by: arch, mckusick
- Get rid of the useless atop() / pmap_phys_address() detour. The
device mmap handlers must now give back the physical address
without atop()'ing it.
- Don't borrow the physical address of the mapping in the returned
int. Now we properly pass a vm_offset_t * and expect it to be
filled by the mmap handler when the mapping was successful. The
mmap handler must now return 0 when successful, any other value
is considered as an error. Previously, returning -1 was the only
way to fail. This change thus accidentally fixes some devices
which were bogusly returning errno constants which would have been
considered as addresses by the device pager.
- Garbage collect the poorly named pmap_phys_address() now that it's
no longer used.
- Convert all the d_mmap_t consumers to the new API.
I'm still not sure wheter we need a __FreeBSD_version bump for this,
since and we didn't guarantee API/ABI stability until 5.1-RELEASE.
Discussed with: alc, phk, jake
Reviewed by: peter
Compile-tested on: LINT (i386), GENERIC (alpha and sparc64)
Runtime-tested on: i386
flag that can be marked on each symmetric op
o eliminate hw.ubsec.maxbatch and hw.ubsec.maxaggr since they are not
needed anymore
o change ubsec_feed to return void instead of int since zero is always
returned and noone ever looked at the return value
Reading the PCI config space with the wrong (larger) size is not
a problem in this case, but writing can be as it clobbers unrelated
registers. In this case the clobbering is for reserved fields, which
too is mostly harmless... for now. Hence, this change is mostly
preventive in nature.
without waiting, since they are called from a system-call context only.
This appears to fix all sorts of problems with open("/dev/dsp", O_WRONLY)
randomly returning ENXIO.
Found by: cognet
o Make DXS3 the primary playback channel. It may be the only
universally supported channel with the assorted revisions of this
chipset.
o Add sysctl and handler for enabling s/pdif output from DXS3.
Retire the "d_dump_t" and use the "dumper_t" type instead.
Dumper_t takes a void * as first arg which is more general than the
dev_t taken by d_dump_t. (Remember: we could have net-dumpers if
somebody wrote us one!)
Define the convention for GEOM controlled disk devices to be that the
first argument to the dumper function is the struct disk pointer.
Change device drivers accordingly.
Change the argument to disk_destroy() to be the same struct disk * as
disk_create() takes.
This enables drivers to ignore the (now) bogus dev_t which disk_create()
returns.
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
Some drives seem to be confused by simultaneous probes.
Tested by: marcel
As a side effect, logical units whose lun is greater than 0 might not be
probed correctly if the lun of 0 doesn't exist in the target because
CAM doesn't scan such luns.
I have a SCSI-FireWire bridge which maps SCSI-ID to LUN and it is an
example of such targets.
dev_t to the method functions.
The dev_t can still be found at struct consdev *->cn_dev.
Add a void *cn_arg element to struct consdev which the drivers can use
for retrieving their softc.
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
support for Tekram DC395U2W cards.
Add a fix submitted by joerg@ to correctly report some errors to CAM.
Use bus_dma instead of the remaining vtophys().
field for holding driver-dependant data. Instead of putting the pointer
to the driver command struct in there, take advantage of these structs
being a (virtually) contiguous array and just put the array index in the
field.
that a command completion happened, all further processing is deferred to
a taskqueue. The taskqueue itself runs implicetely under Giant, but we
already used a taskqueue for the biodone() processing, so this at least
saves the contesting of Giant in the interrupt handler.
retain symetry with aac_alloc_commans(). Since aac_alloc_commands()
allocates fib maps and places them onto the fib lists, aac_free_commands()
should reverse those operations.
o Combine two ifs with the same body with an ||.
o Switch from uintptr_t to uint32_t for fib map load operations.
The target is a uint32_t so using this type for the map load call
avoids an extra cast. uintptr_t should only be used when you need
an "int sized the same as the machine's poitner size" which is not
the case here.
o Removed the commented out M_WAITOK flag in the allocation in
aac_alloc_commands(). The kernel will only block in the allocator
if it can grow the size of the kernel. This usually results in a
page-out which could involve this aac device. Thus, sleeping here
could deadlock the machine. Assuming this operation is occurring outside
of attach time, we have enough fibs to operate anyway, so waiting for
fibs to free up is okay if not optimal.
o In aac_alloc_commands(), if we cannot dmamem_alloc additional fib
space, free the fib map.
o In aac_alloc_commands(), if we cannot create per-command dmamaps, don't
lose track of the fib map that is mapping all of the commands that we
have already released into the free pool. Instead, just cut out of
the loop and modify aac_free_commands to not attempt to free maps that
have not been allocated.
o Don't use a magic number when pre-allocating fibs.
o Use PAGE_SIZE to allocate in page sized chunks instead of an
architecture specific constant.
Submitted by: gibbs
Minor CIS resource allocation code cleanup
Remove some fairly useless debug writes.
This finishes the work to move as much cardbus code as possible into
pci. We wind up removing 800-odd lines from cardbus.c: we go from
1285 to 400 lines.
Reviewed by: mdodd
- Fix memory leak in detaching.
- Initialize fc->status to other than FWBUSREST.
* fwohci.c
- Ignore BUS reset events while BUS reset phase. We can't clear that flag
during bus reset phase.
is encoded in the PCI BAR. The latter is more reliable.
This allows the sio/modem function of the Xircom RealPort ethernet+modem
card to work. Note that there still seem to be issues with sio_pci not
releasing resources on detach.
pci busses implement this.
Also minor comment smithing in cardbus. Fix copyright to this year
with my name on it since I've been doing a lot to this file.
Reviewed by: jhb
- Don't initiate bus reset even if probe failed for some nodes to prevent
infinite bus reset loop.
Problem Reported by: Pierre Beyssac <pb@fasterix.frmug.org>
- Protect timeout routine with splfw() for 4-stable.
* sbp.c
- Make sure to release devq when start request.
Wearing said pointy hat, correct the oversight and hope nobody
notices.
# this should make xircom modems happier to detach once other bugs with
# the cardbus layer are fixed.
Noticed by: scottl
Conical Hat to: imp
o Use the common pci_* routines in preference to the copied and hacked
routines from an ancient pci.c.
This saves 509 lines in cardbus.c. More savings to follow when I
convert the resource code over. In the past when I've done this the
resource code conversion breaks cardbus in subtle ways so I'm doing a
1/2 way checkpoint this time. cardbus still works for me the same as
it did before.
It also looks like cardbus devices now show up as pci bus devices to
pciconf -l, but maybe that was happening before.
Inspired by a patch from Justin Gibbs many moons ago. When he
finishes his kobj multiple inheritance work, we can transition the
finished version of this work to that fairly easily.
To fix scsi, don't wait for ithreads if we're dumping, it makes the
debugger sad.
To fix ata, use what appears to be a polling method if we're dumping,
I stole this from tmm but added code to ensure that this change is
only in effect while dumping.
Tested by: des
