6659 nvlist_free(NULL) is a no-op
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Marcel Telka <marcel@telka.sk>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6659https://github.com/illumos/illumos-gate/commit/aab83bb
Ported-by: David Quigley <dpquigl@davequigley.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4566
When ZFS partitions a block device it must wait for udev to create
both a device node and all the device symlinks. This process takes
a variable length of time and depends on factors such how many links
must be created, the complexity of the rules, etc. Complicating
the situation further it is not uncommon for udev to create and
then remove a link multiple times while processing the udev rules.
Given the above, the existing scheme of waiting for an expected
partition to appear by name isn't 100% reliable. At this point
udev may still remove and recreate think link resulting in the
kernel modules being unable to open the device.
In order to address this the zpool_label_disk_wait() function
has been updated to use libudev. Until the registered system
device acknowledges that it in fully initialized the function
will wait. Once fully initialized all device links are checked
and allowed to settle for 50ms. This makes it far more likely
that all the device nodes will exist when the kernel modules
need to open them.
For systems without libudev an alternate zpool_label_disk_wait()
was updated to include a settle time. In addition, the kernel
modules were updated to include retry logic for this ENOENT case.
Due to the improved checks in the utilities it is unlikely this
logic will be invoked. However, if the rare event it is needed
it will prevent a failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4523Closes#3708Closes#4077Closes#4144Closes#4214Closes#4517
When partitioning a device a name may be specified for each partition.
Internally zfs doesn't use this partition name for anything so it
has always just been set to "zfs".
However this isn't optimal because udev will create symlinks using
this name in /dev/disk/by-partlabel/. If the name isn't unique
then all the links cannot be created.
Therefore a random 64-bit value has been added to the partition
label, i.e "zfs-1234567890abcdef". Additional information could
be encoded here but since partitions may be reused that might
result in confusion and it was decided against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4517
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
This issue was caused by calling `thread_init()` and `thread_fini()`
multiple times resulting in `kthread_key` being invalid. To resolve
the issue the explicit calls to `thread_init()` and `thread_fini()`
required by the `zpool` command have been moved in to the command.
Consumers such as `zdb` and `zhack` perform the same initialized
through `kernel_init()` and `kernel_fini()`.
Resolving this issue allows multiple additional test cases to
be enabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#4331
When checking a whole disk to see if it can be safely added to
the pool a variety of checks are done. One of those checks is
to attempt to determine the partition information and scan all
the partitions for existing filesystems.
Since ZoL contains a EFI library this partition scanning is
easy to do for GPT partitioned disks. However, for non-GPT
partitioned disks (MBR/EBR) things are a bit harder. The lack of
a convenient library means non-GPT partitioned disks will not
have all their partitions checked. For this reason, the default
behavior was to require the force option. For example:
invalid vdev specification
use '-f' to override the following errors:
/dev/vdb does not contain an GPT label but it may contain partition
information in the MBR.
However in practice requiring the force option for this case is
counter-intuitively less safe. The reason is because only the first
error is returned. By passing the force option it will suppress
this first warning and potentially others you were not aware of.
Therefore this patch inverts the default behavior for non-GPT
formated disks (unformatted, MBR/EBR, etc). If no GPT table is
detected and there is no file system detected on the provided
block device. Then it will be assumed that block device is safe
to use.
Longer term it would be nice to see MBR/EBR scanning added to
the utilities. This should be fairly straight forward to do.
However these days it's somewhat less critical because Linux
defaults to GPT partition tables for devices 2TB or larger.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2660Closes#2274
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4368
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
5767 fix several problems with zfs test suite
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5767https://github.com/illumos/illumos-gate/commit/52244c0
Porting Notes:
- Only the updates to zpool_main.c were kept because the ZFS test
suite is not currently part of the ZoL source tree. The test
suite itself should be updated to include the latest versions
of the tests once we're running it for every commit
- Fixes `zpool list` output.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5959 clean up per-dataset feature count code
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/5959https://github.com/illumos/illumos-gate/commit/ca0cc39
Porting notes:
illumos code doesn't check for feature_get_refcount() returning
ENOTSUP (which means feature is disabled) in zdb. zfsonlinux added
a check in https://github.com/zfsonlinux/zfs/commit/784652c
due to #3468. The check was reintroduced here.
Ported-by: Witaut Bajaryn <vitaut.bayaryn@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3965
All other sections use a tab, which makes them easy to parse. Only the
"scan:" section had its continuation lines indented with four spaces.
This makes them consistent with the others.
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#3769
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
5118 When verifying or creating a storage pool, error messages
only show one device
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Boris Protopopov <boris.protopopov@me.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://github.com/illumos/illumos-gate/commit/75fbdf9https://www.illumos.org/issues/5118
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3567
4966 zpool list iterator does not update output
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://github.com/illumos/illumos-gate/commit/cd67d23https://www.illumos.org/issues/4966
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3566
sysstat's iostat omits the first report when the -y option is used.
This patch adds that functionality and omits the first report with
statistics since system boot.
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3439
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Support exporting all imported pools in one go, using 'zpool export -a'.
This is accomplished by moving the export parts from zpool_do_export()
in to the new function zpool_export_one(). The for_each_pool() function
is used to enumerate the list of pools to be exported. Passing an argc
of 0 implies the function should be called on all pools.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #3203
5134 if ZFS_DEBUG or debug= is set, libzpool should enable debug prints
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/projects/illumos-gate/issues/5134https://github.com/illumos/illumos-gate/commit/7fa49ea
Porting notes:
Added dprintf_setup() to main in zfs_main.c and zpool_main.c.
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2669
The newroot nvlist should be freed before returning.
Signed-off-by: Isaac Huang <he.huang@intel.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3264
When using 'zpool import' to scan for available pools prefer vdev names
which reference vdevs with more valid labels. There should be two labels
at the start of the device and two labels at the end of the device. If
labels are missing then the device has been damaged or is in some other
way incomplete. Preferring names with fully intact labels helps weed out
bad paths and improves the likelihood of being able to import the pool.
This behavior only applies when scanning /dev/ for valid pools. If a
cache file exists the pools described by the cache file will be used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Closes#3145Closes#2844Closes#3107
In dry run mode, zpool should display more of the proposed pool
configuration for "zpool add". This commit adds support for displaying
cache devices.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1106
If spl_hostid is set via module parameter, it's likely different from
gethostid(). Therefore, the userspace tool should read it first before
falling back to gethostid().
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3034
Commit c66989b accidentally introduced a cstyle issue which went
unnoticed. This tiny patch corrects that oversight.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In userland we need to switch over to the temporary name once the
pool has been created, otherwise the root dataset won't mount
and the error "cannot open 'the_real_name': dataset does not exist"
is printed.
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2760
Change the zpool program to skip its hostid mismatch check in the
same way that libzfs already does.
Invoked imports fail if the ZPOOL_CONFIG_HOSTID nvpair is missing in
the /etc/zfs/zpool.cache file, which can happen as of the /etc/hostid
deprecation in commit zfsonlinux/spl@acf0ade362.
Signed-off-by: Darik Horn <dajhorn@vanadac.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2794
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
zpool import's -t parameter is intended for use with -R when operating
on pools that belong to other systems. Like -R, pools imported in this
way should not update the cachefile unless explicitly requested. The
initial implementation allowed the cachefile to be updated when -R was
not used. This went uncaught during testing because -R had implicitly
disabled use of the cachefile.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
Adding to a property list only if there is no existing value is used
twice. Once by zpool create -R and again by zpool import -R. Now that
zpool create -t and zpool import -t also need it, lets refactor it into
a helper function to make the code more readable.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
The 'zpool list -v' command displays lots of info but excludes the
capacity of each disk. This should be added.
5147 zpool list -v should show individual disk capacity
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5147https://github.com/illumos/illumos-gate/commit/7a09f97
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2688
Change mount code to diagnose filesystem versions that
are not supported by the current implementation.
Change upgrade code to do likewise and refuse to upgrade
a pool if any filesystems on it are a version which is
not supported by the current implementation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Closes: #2616
4970 need controls on i/o issued by zpool import -XF
4971 zpool import -T should accept hex values
4972 zpool import -T implies extreme rewind, and thus a scrub
4973 spa_load_retry retries the same txg
4974 spa_load_verify() reads all data twice
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/4970https://www.illumos.org/issues/4971https://www.illumos.org/issues/4972https://www.illumos.org/issues/4973https://www.illumos.org/issues/4974https://github.com/illumos/illumos-gate/commit/e42d205
Notes:
This set of patches adds a set of tunable parameters for the
"extreme rewind" mode of pool import which allows control over
the traversal performed during such an import.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2598
The Intel DC S3500 and Intel DC S3700 are optimized to handle 4KB
sectors well despite of their 8KB page sizes, so we move them to a new
category for enterprise drives where they will receive ashift=12. They
are joined by the Intel 730 series, which uses the same disk controller,
as well as a San Disk enterprise drive. The drive IDs for these two were
obtained by myself with the drive_id utility. The drive ID for the 240GB
Intel 730 model was extrapolated from the drive ID for the 480GB model.
Lastly, we also add some Western Digital mobile drives. ryuo in
\#zfsonlinux on freenode obtained "ATA WDC WD2500BEVT-0" from
running drive_id on his own hardware. The additional drives in that
family were extrapolated from that identifer.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2601
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
4374 dn_free_ranges should use range_tree_t
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4374https://github.com/illumos/illumos-gate/commit/bf16b11
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2531
4171 clean up spa_feature_*() interfaces
4172 implement extensible_dataset feature for use by other zpool features
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Garrett D'Amore <garrett@damore.org>a
References:
https://www.illumos.org/issues/4171https://www.illumos.org/issues/4172https://github.com/illumos/illumos-gate/commit/2acef22
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2528
This functionality is already available in 'zfs get'. Providing
it for 'zpool get' is useful and good for consistency.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #2522
Users need to be aware that when replacing devices in an existing
pool they may need to override automatically detected ashift value.
This will all depend on the exact hardware they are using.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2024
Verbatim imports can cause hostid mismatches, but things otherwise work. `zpool
status` does not handle this and will fail when assertions are enabled:
```
zpool: ../../cmd/zpool/zpool_main.c:4418: status_callback: Assertion `reason == ZPOOL_STATUS_OK' failed.
Program received signal SIGABRT, Aborted.
```
Lets instead add a case to display an informative message such as this:
```
pool: rpool
state: ONLINE
status: Mismatch between pool hostid and system hostid on imported pool.
This pool was previously imported into a system with a different hostid,
and then was verbatim imported into this system.
action: Export this pool on all systems on which it is imported.
Then import it to correct the mismatch.
see: http://zfsonlinux.org/msg/ZFS-8000-EY
scan: scrub repaired 0 in 0h8m with 0 errors on Thu Apr 17 19:43:57 2014
config:
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
sda ONLINE 0 0 0
errors: No known data errors
```
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2342
zfsonlinux/zfs@1db7b9be75 should have
fixed this, but this particular string was overlooked.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2288
This functionality has always been missing. But until now there
were no zevents which included an array of strings so it wasn't
missed. However, that's now changed so to ensure this information
is output correctly by 'zpool events -v' the DATA_TYPE_STRING_ARRAY
has been implemented.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
Due to the very poorly chosen argument name 'cleanup_fd' it was
completely unclear that this file descriptor is used to track the
current cursor location. When the file descriptor is created by
opening ZFS_DEV a private cursor is created in the kernel for the
returned file descriptor. Subsequent calls to zpool_events_next()
and zpool_events_seek() then require the file descriptor as an
argument to reposition the cursor. When the file descriptor is
closed the kernel state tracking the cursor is destroyed.
This patch contains no functional change, it just changes a
few variable names and clarifies the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
Originally, users had to handle spa namespace collisions by either
exporting the already imported pool or by specifying a new name for the
pool with a conflicting name. In the case of root pools from virtual
guests, neither approach to collision resolution is reasonable. This is
addressed by extending the new name syntax with a -t option to specify
that the new name is temporary. When specified, this sets an internal
flag that is passed into the kernel to tell it that all label updates
should refer to the name used in the original label. Consequently, the
original pool name will be retained on export.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2189
ZoL commit 1421c89 unintentionally changed the disk format in a forward-
compatible, but not backward compatible way. This was accomplished by
adding an entry to zbookmark_t, which is included in a couple of
on-disk structures. That lead to the creation of pools with incorrect
dsl_scan_phys_t objects that could only be imported by versions of ZoL
containing that commit. Such pools cannot be imported by other versions
of ZFS or past versions of ZoL.
The additional field has been removed by the previous commit. However,
affected pools must be imported and scrubbed using a version of ZoL with
this commit applied. This will return the pools to a state in which they
may be imported by other implementations.
The 'zpool import' or 'zpool status' command can be used to determine if
a pool is impacted. A message similar to one of the following means your
pool must be scrubbed to restore compatibility.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #1 detected.
action: The pool can be imported using its name or numeric identifier,
however there is a compatibility issue which should be corrected
by running 'zpool scrub'
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
$ zpool status
pool: zol-0.6.2-173
state: ONLINE
scan: pool compatibility issue detected.
see: https://github.com/zfsonlinux/zfs/issues/2094
action: To correct the issue run 'zpool scrub'.
config:
...
If there was an async destroy in progress 'zpool import' will prevent
the pool from being imported. Further advice on how to proceed will be
provided by the error message as follows.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #2 detected.
action: The pool can not be imported with this version of ZFS due to an
active asynchronous destroy. Revert to an earlier version and
allow the destroy to complete before updating.
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
Pools affected by the damaged dsl_scan_phys_t can be detected prior to
an upgrade by running the following command as root:
zdb -dddd poolname 1 | grep -P '^\t\tscan = ' | sed -e 's;scan = ;;' | wc -w
Note that `poolname` must be replaced with the name of the pool you wish
to check. A value of 25 indicates the dsl_scan_phys_t has been damaged.
A value of 24 indicates that the dsl_scan_phys_t is normal. A value of 0
indicates that there has never been a scrub run on the pool.
The regression caused by the change to zbookmark_t never made it into a
tagged release, Gentoo backports, Ubuntu, Debian, Fedora, or EPEL
stable respositorys. Only those using the HEAD version directly from
Github after the 0.6.2 but before the 0.6.3 tag are affected.
This patch does have one limitation that should be mentioned. It will not
detect errata #2 on a pool unless errata #1 is also present. It expected
this will not be a significant problem because pools impacted by errata #2
have a high probably of being impacted by errata #1.
End users can ensure they do no hit this unlikely case by waiting for all
asynchronous destroy operations to complete before updating ZoL. The
presence of any background destroys on any imported pools can be checked
by running `zpool get freeing` as root. This will display a non-zero
value for any pool with an active asynchronous destroy.
Lastly, it is expected that no user data has been lost as a result of
this erratum.
Original-patch-by: Tim Chase <tim@chase2k.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2094
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
