getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
if I586_CPU is defined. Note there is a runtime check so the code
won't be run for non-Pentium CPUs anyway.
2.2 candidate, this code has been tested for almost half year in -current.
will be renamed.
Fixed comments about unsupported network protocols.
ncr0 is a controller, not a device. This make no difference.
Added undocumented options DEVFS_ROOT, I586_CTR_GUPROF and I586_PMC_GUPROF.
Sorted undocumented options.
bit (0x0008) in the sc driver configuration line. This way it's easy to
boink a generic kernel.
Also, document and place in an opt_ file the #define's for overriding which
serial port is the system console.
Approved by: sos
I maintain that it saves more power to simply "hlt" the CPU than to
spend tons of time trying to tell the APM bios to do the same.
In particular if you do it 100 times a second...
It worked because it is spelled correctly in LINT.
Added old obscure syscons options MAXCONS, SLOW_VGA and XT_KEYBOARD.
This file should be sorted both alphabetically and on the module
name by using a consistent prefix for each module, but there is no
consistency in the old options. E.g., MAXCONS is spelled PCVT_NSCREENS
for pcvt.
If you define this, it means your keyboard is actually probable using the
brain-dammaged probe routine in syscons, and if the keyboard is NOT found,
then you don't want syscons to activate itself further.
This makes life sane for those of us who use serial consoles most of the
time and want "the right thing" to happen when we plug a keyboard in.
This stuff should not be too destructive if the IPDIVERT is not compiled in..
be aware that this changes the size of the ip_fw struct
so ipfw needs to be recompiled to use it.. more changes coming to clean this up.
based on the HD64570 chip. Both the 1 and 2 port cards is supported.
Line speeds of up to 2Mbps is possible. At this speed about 95% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the X.21 interface is tested. The others may need
tweaks to the clock selection code.
to be allocated at boot time. This is an expensive option, as they
consume physical ram and are not pageable etc. In certain situations,
this kind of option is quite useful, especially for news servers that
access a large number of directories at random and torture the name cache.
Defining 5000 or 10000 extra vnodes should cut down the amount of vnode
recycling somewhat, which should allow better name and directory caching
etc.
This is a "your mileage may vary" option, with no real indication of
what works best for your machine except trial and error. Too many will
cost you ram that you could otherwise use for disk buffers etc.
This is based on something John Dyson mentioned to me a while ago.
1) A spelling error pointed out by Paco Hope.
2) A bug in the range checking routing pointed out by Jim Bray.
3) Enables the setting of frames per second.
Submitted-By: Jim Lowe <james@miller.cs.uwm.edu>
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
isn't supplying all the proper header info here! Last commit of fe0
entry should have had the following Submitted by line also).
Submitted-by: Masahiro SEKIGUCHI <seki@sysrap.cs.fujitsu.co.jp>
