in cyopen() were done in a different order than in sioopen(), partly
to (ab)use a side effect of comparam() and partly because I didn't
understand what the reset was doing (it flushes the fifos). This
turned out to be more than a cosmetic problem. Flushing the fifos
quite late is good for discarding input that arrived while the line
state was being initialized, and in the cy driver it also seems to
reduce a problem with input that arrived long ago during the previous
close (the UART loses sync too easily and for too long).
change the original code but add an extra option "ALI_V" to check the
precise IDE port.(especially, secondary) Use the same option "ALI_V" on
the kernel config file to prevent generic DMA check causes wrong result.
(It seems buggy even on PIIX4 chipset, and I don't know when this bug start)
Should I add the option "ALI_V" into /sys/i386/conf/LINT ?
ethernet driver.
The BUGS section is still impressive, but the driver seems to work for
me now. Disclaimer: i haven't been able to test this under -current
so far (but it compiles, and the notebook it's intended for can now be
updated to -current more easy than before). Don't be afraid of the
many #ifdefs on __FreeBSD_version in the imported file; i want them in
the repository on the vendor-branch so other people can also manually
integrate it into older systems. I'll clean it up on the -current
branch in a followup commit. The vendor-banch version right now
supports systems back to 2.2R.
This driver should be layered upon ppc(4), but i currently have no
idea how to do this.
Eventually i'll further develop the driver to also support the more
modern RTL 8012 success, which seems to be present in a number of
cheap pocket ethernet adapters these days. Right now, i doubt it will
run with the 8012 without any changes.
Finally a big Thanks! to RealTek for promptly providing me with
documentation and with the source code for the 8012 pocket driver upon
request. I wish all vendors were that cooperative!.
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
Not tested on the if_sr, if_cx and if_ar drivers, but
expected to work just the same as it used to.
Any users of these drivers (or even better: donors
of hardware for them) please contact phk@freebsd.org
so we can test the next batch of changes to if_sppp.
as well as several functional additions.
(1) dot3 MIB support.
(2) if_media selection method support.
(3) bridge support.
(4) new boards support. Supported boards are as follows.
[PC/AT]
* Fujitsu FMV-180 series
* Allied-Telesis RE2000 series
* Allied-Telesyn AT1700 series
* Gateway Communications G/Ether series
* UB networks Access/PC ISA series
* TDK/LANX LAC-AX series
* ICL EtherTeam16i series
* RATOC REX-5586/5587
[PC-98]
* Allied-Telesis RE1000 series
* Allied-Telesis RE1000Plus/ME1500 series
* Contec C-NET(9N)E series
* Contec C-NET(98)P2 series
* UB networks Access/PC N98C+ series
* TDK/LANX LAC-98 series(not tested)
Submitted by: seki@sysrap.cs.fujitsu.co.jp (Masahiro Sekiguchi) and
chi@bd.mbn.or.jp (Chiharu Shibata)
in rev.1.30 (just before FreeBSD-1.1R) to almost match corresponding
breakage in FreeBSD-1.x's diskerr(). FreeBSD-2.x's diskerr() never
had the breakage.
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
were half of their physical offsets for ISA and 1/4 of their physical
offsets for PCI, while all other Cyclades offsets were physical/1 for
ISA and physical/2 for PCI. Logically wrong macros were used to scale
CY16_RESET and CY_CLEAR_INTR to the correct physical offsets.
Fixed some style bugs (mostly long lines).
interrupt handlers. Instead, load and use it atomically as necessary.
This reduces mode switching overhead for "polled" mode interrupt handling
from 5 i/o's to 3 (per service type, per port) so that polled mode is only
slightly more inefficient than "interrupt" mode.
UARTs when their divisor latch registers are selected while they are
doing output. Waiting for (some) output to drain is not permitted for
the TCSANOW case of tcsetattr(). NIST-PCTS easily detects bugs like
this by testing at at speeds that no one would want to use (50 bps).
Deleted stale comments related to flushing i/o. Flushing works properly
for 16550s according to NIST-PCTS (it can't work properly for 16450s).
This finishes fixing all sio(16550)-related bugs found by NIST-PCTS.
keyboard/mouse/display switch products (console switches). Some
products claim they emulate the PS/2 mouse when the host computer
talks to the mouse while the mouse is actually routed to another
host.
flags 0x200 Do not try to identify the mouse model. All
mice will be recognized as "generic PS/2".
0x400 Do not reset the mouse. Some switches' response
to the reset command is too slow and the psm
will timeout.
0x1000 Relax error checking when probing the mouse
port.
- Added another flag for pad devices.
flags 0x800 Assume the pad behaves like ALPS GlidePoint
when the user `taps' the surface of the pad;
it will be reported as the fourth button.
devstart_start_transaction() call is misplaced - it is after the
wdustart() call that queues the transaction on the controller queue.
Normally this doesn't matter because we're running at splbio() so
nothing will look at the controller queue. However, obsolescent
code for syncing labels sometimes slept after the transaction was
started, so the transaction sometimes completed before it was
[recorded as] started. This code was misplaced even for syncing
labels. Move it to the right place. It should go away, but
something may depend on its side effects.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
minor devices.
Improve PLL/OCXO DAC dithering.
General remodeling.
Performance is now 2.5e-11 in frequency and +/- 100 nsec in time, both
of which are actually the limits of the transmitted signal.
bug sound was not played if the total amount of data written to
the device was less than one blocksize
Noticed by: NABETANI Masaki and FreeBSD-users-jp
1) The vnode pager wasn't properly tracking the file size due to
"size" being page rounded in some cases and not in others.
This sometimes resulted in corrupted files. First noticed by
Terry Lambert.
Fixed by changing the "size" pager_alloc parameter to be a 64bit
byte value (as opposed to a 32bit page index) and changing the
pagers and their callers to deal with this properly.
2) Fixed a bogus type cast in round_page() and trunc_page() that
caused some 64bit offsets and sizes to be scrambled. Removing
the cast required adding casts at a few dozen callers.
There may be problems with other bogus casts in close-by
macros. A quick check seemed to indicate that those were okay,
however.
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
specified. This makes haveseen_isadev() useful for searching for a
free resource. This increases the bitrot in the pci RESOURCE_CHECK
code.
Fixed the pre-attach conflict message. The flag for distinguishing
pre-attach conflict checks from pre-probe ones was never set.
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
DEB macro). There are probably quite a few other messages that warrant
a similar treatment, and many more that should be converted to plain
log messages (e.g. "WARNING: wrintr but write DMA inactive!"). Now
that I think of it, same goes for the CAM code (e.g. the famed "tagged
openings" message)
reported bug.
At using tcpdump for cs interface, tcpdump only dump packet which
src or dst MAC-address is cs interface. cs interface can't look up
packet between others.
Submitted by: MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
add support for Vibra16X, OPTi925, and bring in several assorted
fixes to the code and documentation.
Also present here are apm hooks so that laptops can properly
reconfigure the hardware after suspend (tested on the Libretto50).
Reviewed by: jordan
