blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
If for some reason DEVFS is undesired, the "NODEVFS" option is
needed now.
Pending any significant issues, DEVFS will be made mandatory in
-current on july 1st so that we can start reaping the full
benefits of having it.
exactly the same functionality via a sysctl, making this feature
a run-time option.
The default is 1(ON), which means that /dev/random device will
NOT block at startup.
setting kern.random.sys.seeded to 0(OFF) will cause /dev/random
to block until the next reseed, at which stage the sysctl
will be changed back to 1(ON).
While I'm here, clean up the sysctls, and make them dynamic.
Reviewed by: des
Tested on Alpha by: obrien
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
Only PCI and on-board ISA peripherials are supported at this time.
This support has been only lightly tested due to a lack of response to my
call for testers on the freebsd-alpha mailing list. It works quite well
on the one AS2100 on which it has been tested, but it may not work on
an AS2100A and should therefore be regarded as experimental.
