This completes the effort to handle dependent functions, which are used
in some machines for irq link resources. Also, clean up some nearby
comments while I'm at it.
level of abstraction for any and all CPU mask and CPU bitmap variables
so that platforms have the ability to break free from the hard limit
of 32 CPUs, simply because we don't have more bits in an u_int. Note
that the type is not supposed to solve massive parallelism, where
the number of CPUs can be larger than the width of the widest integral
type. As such, cpumask_t is not supposed to be a compound type. If
such would be necessary in the future, we can deal with the issues
then and there. For now, it can be assumed that the type is integral
and unsigned.
With this commit, all MD definitions start off as u_int. This allows
us to phase-in cpumask_t at our leasure without breaking anything.
Once cpumask_t is used consistently, platforms can switch to wider
(or smaller) types if such would be beneficial (or not; whatever :-)
Compile-tested on: i386
This change has not been tested.
This change was triggered by a gcc(1) warning on ia64 at -O2. The
variable v was not used after being computed, which resulted in enough
dead code elimination (DCE) to confuse the compiler and emit a bogus
warning about the use of the variable i without prior definition. The
variable i is the loop variable.
Submitted by: des
Responsibility: marcel
for uart(4) to figure out which device to use as console. Use this file
to define hw.uart.console instead so that we don't have to put it in
the default loader.conf, which makes it hard to override.
to select a serial console and debug port (resp). On ia64 these replace
the use of hints completely and take precedence over hints on alpha,
amd64 and i386. On sparc64 these variables are not yet recognised.
The reasons for introducing these variables are:
1. Hints have side-effects. They reserve the unit number for use by
isa or acpi devices and therefore cannot be used to select a pci
device. Also, the use of a unit number to select a device prior
to bus enumeration is nonsense. The new variables have no side-
effects and are not based on unit numbers.
2. Hints don't have the expression power to allow the sysadmin to
select UARTs that are not legacy PC devices and need the support
of compile-time constants to give the sysadmin some level of
flexibility.
The hw.uart.console and hw.uart.dbgport variables specify a list of
attributes. An attribute is a tag-value pair, seperated by a colon.
Attributes are seperated by a comma. Where possible, tags are the
same as those in /etc/remote (only br and pa in practice). Details
can be found in the manpage (not part of this commit).
Not tested on: amd64, pc98
from ddp_usrreq.c. Functions moved are:
at_pcballoc()
at_pcbconnect()
at_pcbdetach()
at_pcbdisconnect()
at_pcbsetaddr()
at_sockaddr()
Also moved are ddp_ports and ddpcb, global variables associated with DDP
pcbs. This makes PCB implementation more parallel to inet, inet6, and
ipx.
device, the device is probed multiple times (so each device is
detected N times after unloading/loading the module N-1 times).
The real fix is (quote Doug and Warner):
> : In an ideal world, there should be some kind of BUS_UNIDENTIFY method
> : which a driver could use to delete the devices it created in
> : BUS_IDENTIFY.
>
> Or the bus would have a driver deleted routine that got called and it
> would remove all instances of the devclass attached to it.
Reviewed by: Doug Rabson & Warner Losh
to mmap it PROT_EXEC. This also depends on the architecture, as some
architextures (e.g. i386) do not distinguish between read and exec pages
Inspired by: http://linux.bkbits.net:8080/linux-2.4/cset@1.1267.1.85
Reviewed by: alc
mappings required by mdstart_swap(). On i386, if the ephemeral mapping
is already in the sf_buf mapping cache, a swap-backed md performs
similarly to a malloc-backed md. Even if the ephemeral mapping is not
cached, this implementation is still faster. On 64-bit platforms, this
change has the effect of using the direct virtual-to-physical mapping,
avoiding ephemeral mapping overheads, such as TLB shootdowns on SMPs.
On a 2.4GHz, 400MHz FSB P4 Xeon configured with 64K sf_bufs and
"mdmfs -S -o async -s 128m md /mnt"
before:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.430923 secs (311465697 bytes/sec)
after with cold sf_buf cache:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.367948 secs (364773576 bytes/sec)
after with warm sf_buf cache:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.252826 secs (530870010 bytes/sec)
malloc-backed md:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.253126 secs (530240978 bytes/sec)
I've added -fno-strict-aliasing for now so we can ease into this.
I wanted to shoot for -O3, but the inlining caused problems due to GCC's
size heuristics; so also add -frename-registers, which is one of the things
-O3 would have given us.
entry size and the ELF version. Also, avoid a potential integer
overflow when determining whether the ELF header fits entirely
within the first page.
Reviewed by: jdp
A panic when attempting to execute an ELF binary with a bogus program
header table entry size was
Reported by: Christer Öberg <christer.oberg@texonet.com>
the tap driver, even with Giant over the cdev operation vector, due to
a non-atomic test-and-set of the si_drv1 field in the dev_t. This bug
exists with Giant under high memory pressure, as malloc() may sleep
in tapcreate(), but is less likely to occur. The resolution will
probably be to cover si_drv1 using the global tapmtx since no softc is
available, but I need to think about this problem more generally
across a range of drivers using si_drv1 in combination with SI_CHEAPCLONE
to defer expensive allocation to open().
Correct what appears to be a bug in the original if_tap implementation,
in which tapopen() will panic if a tap device instance is opened more
than once due to an incorrect assertion -- only triggered if INVARIANTS
is compiled in (i.e., when built into a kernel). Return EBUSY instead.
Expand mtx_lock() coverage using tp->tap_mtx to include tp->ether_addr.
