that one cannot generally hold a lock and call bus_teardown_intr.
This is race free with wi_intr because bus_teardown_intr won't allow
wi_intr to be called after it returns.
# jeff hsu points out that there might be a race between this unlock
# and wi_start. While that may be true also, it won't impact this commit.
Submitted by: jhb
firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets
past doing dhclient, but hangs on transmit a little after the ip
address is set. The 1.50.12 card has always been 'cranky' and Bill
Paul's tearing it apart at FreeBSD '99 hasn't helped.
sc_reset and sc_enable are subtlely different things. sc_reset means
exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE
has been sent to the card without a WI_CMD_DISABLE following." This
is a little different than what they mean on NetBSD (where both of
these concepts are comingled). NetBSD will try to only enable symbol
cards once, while FreeBSD only sends the WI_CMD_INI once.
Also, only try once to reset the card on a symbol.
This makes the lucent cards no worse than before, but apparently not
much better either. I got fewer hangs in my testing than I have in
the past, but I don't know if it is statistically significant or not.
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
of the entries have a description, we'll use that to override the
description that the pccard layer generates for us.
This saves about 930 bytes in the module, so I feel it won't hurt the
crowded boot disks....
# other modules to follow
Change 27224 by imp@imp_hammer on 2003/03/22 00:16:22
Put what I think are the correct TX RATE translation tables
in place for LUCENT firmware. This is based on the 4.x driver.
Maybe it should be table driven?
ifconfig wi0 media DS/11Mbps still fails, but it fails before
we even get to the txrate stuff, so other things are wrong.
Change 27225 by imp@imp_hammer on 2003/03/22 00:45:11
Default ic_fixed_rate to -1. This is the same thing as autoselect.
There really should be a #define for this...
one tx buffer for these cards. The old driver only used one. We use
1 for symbol, and 3 for prism cards.
o Don't do the maximum loops thing in the ISR. In fact, revert to the
old interrupt handler. Lucent cards don't seem to work too well if
you don't disable/enable interrupts from the card in the ISR.
Between these two changes, Lucent cards suck less. They work in
autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a
specific media speed doesn't work, and I've had a few issues even with
these patches. They turn a former brick into a nearly useful card.
These patches work on the prism 2 and 2.5 PC Card cards that I have.
I've not tested this on PCI cards. I suspect, but couldn't find
proof, that they were the reason that the ISR was changed so radically
from its FreeBSD roots in NetBSD. We might need to have a variant ISR
if so.
code both seem to call wi_start (directly or via the if_start pointer)
without checking to see if OACTIVE is 0. In addition, I think that
with the use of 3 transmit buffers this routine can be called with
OACTIVE set, but I might be mistaken about that (and it doesn't
matter).
Reviewed by: sam
Noticed by: imp, alfred, ambrisko
attach routine, calling WIUNLOCK in the error case of one of the ifs
for that routine is now bogus. This should have been removed when the
WILOCK() was removed, but wasn't.
Submitted by: "Harti Brandt" <brandt@fokus.fraunhofer.de>
at which tx errors are printed (default to 0); hw.wi.debug control the debug
msgs and is only present when WI_DEBUG is defined at compile time (the default
for the moment)
Requested by: imp
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
and the AT24C08 small serial flash parts. We still report these as
the same part (since we group things already), but now we recognize
the small serial versions as well.
firmware revision as well (not sure which firmware versions are needed
for this, but the 6.x and 8.x 'software' versions that I have seem to
support it).
Add dBm comm quality RID. This is like the normal comm quality rid,
except the signal and noise numbers are normalized to dBm. Some
revisions of the prism firmware, however, don't support this RID, and
some that do support it return 0 for quality and/or noise. Your
milage may vary.
