This will prevent that the script hangs during startup, which
could cause annoying effects after rebooting for example.
PR: kern/139422
Submitted by: Andrey Groshev <greenx at yartv dot ru>
Approved by: imp (mentor, implicit)
MFC after: 3 days
Facilitated by: Snow B.V.
By misinterpreting some data, I thought that getty wouldn't apply any
baud rate to the syscons devices, but it uses the default entry instead.
This means that the baud rate is set to 1200. This isn't too bad, except
when using canonical mode. Make it use 9600 baud by default.
MFC after: 1 week
Devices that don't implement param() (which means they don't support
hardware parameters such as flow control, baud rate) hardcode the baud
rate to TTYDEF_SPEED. This means the buffer size cannot be configured,
which is a little inconvenient when using canonical mode with big lines
of input, etc.
Make it adjustable, but do clamp it between B50 and B115200 to prevent
awkward buffer sizes. Remove the baud rate assignment from
/etc/gettytab. Trust the kernel to fill in a proper value.
Reported by: Mikolaj Golub <to my trociny gmail com>
MFC after: 1 month
employ a more generic solution, and use it in the individual rc.d scripts
that also have an $rc_quiet test:
1. Add check_startmsgs() to rc.subr.
2. In the rc.d scripts that use rc_quiet (and rc.subr) substitute
variations of [ -z "$rc_quiet" ] with check_startmsgs
3. In savecore add a trailing '.' to the end of the message to make it
more consistent with other scripts.
4. In newsyslog remove a : before the terminal '.' since we do not expect
there to be anything printed out in between to make it more consistent.
5. In the following scripts change "quotes" to 'quotes' where no variables
exist in the message: savecore pf newsyslog
6. In the following scripts substitute if/then/fi for the simpler (and
more consistent) check_startmsgs &&: faith stf
7. In the following scripts separate the "Starting foo:" from the terminal
'.' to make them more consistent: moused hostname pf
8. In nfsclient move the message to its own line to avoid a style bug
9. In pf rc_quiet does not apply to the _stop method, so remove the
test there.
10. In motd add 'quotes' around the terminal '.' for consistency
for each address family. Replace AF_static() with static_AF() for
consistency.
- Display a message only if the user sets a non-default value, and set
a sysctl explicitly even if it is the default value.
- Split netoptions_start() to netoptions_AF() and add afexists() check
for each address family.
- Display a message only if the user sets a non-default value, and set
a sysctl explicitly even if it is the default value.
Spotted by: Pegasus Mc Cleaft[*]
an IPv6 support.
Reported by: Alexander Best <alexbestms__at__math.uni-muenster.de>
Confirmed by: Paul B. Mahol <onemda__at__gmail.com>,
Alexander Best <alexbestms__at__math.uni-muenster.de>
fstab: /etc/fstab:0: No such file or directory
and from dump(8) when setfsent(3) fails due to /etc/fstab not existing:
DUMP: Can't open /etc/fstab for dump table information: No such...
This makes daily and security periodic runs somewhat cleaner in jails
which lack /etc/fstab files.
MFC after: 1 month
re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
legacy IP handling rather than the IPv6 version.
Reported by: Pegasus Mc Cleaft (ken mthelicon.com)
Tested by: Pegasus Mc Cleaft (ken mthelicon.com)
MFC after: 2 days
X-MFX with: r197139
network_ipv6->rc.d/netif integration:
- $ipv6_enable is now obsolete. Instead, IPv6 is enabled by
default if the kernel supports it, and $ipv6_network_interfaces
is "none" by default. If you want to use IPv6, define
$ipv6_network_interfaces and $ifconfig_xxx_ipv6.
An interface which is in $network_interfaces and not in
$ipv6_network_interfaces will be marked as "inet6
-auto_linklocal ifdisabled" (see ifconfig(8)).
- $ipv6_ifconfig_xxx is renamed to ifconfig_xxx_ipv6 for
consistency with other address families. The old variables
still work but can be removed in the future. Note that
ipv6_ifconfig_xxx="..." should be replaced with
ifconfig_xxx_ipv6="inet6 ...".
- Receiving ICMPv6 Router Advertisement is not automatically
enabled even if there is no manual configuration of IPv6 in
rc.conf. If you want it, define
ifconfig_xxx_ipv6="inet6 ... accept_rtadv".
- The rc.d/ip6addrctl now chooses address selection policy based
on $ipv6_prefer, not $ipv6_enable. The default is
ipv6_prefer=NO.
- $router* and $ipv6_router* are replaced with $routed_* and
$route6d_* for consistency. The old variables still work but
can be removed in the future.
MFC after: 3 days
and $desc.
The set_rcvar_obsolete() is for displaying an obsolete variable
and the new one. More specifically, a warning is displayed when
a variable is removed or changed in the source tree and the user
still defines the old one.
$router* and $ipv6_router* are replaced with $routed_* and
$route6d_* for consistency. The old variables still work but
can be removed in the future.
MFC after: 3 days
- Add rc.d/stf and rc.d/faith for stf(4) and faith(4).
- Remove rc.d/auto_linklocal and rc.d/network_ipv6.
- Move rc.d/sysctl to just before FILESYSTEMS because rc.d/netif
depends on some sysctl variables.
Reviewed by: brooks
MFC after: 3 days
it from the build.
If you are using the FTP daemon, please consider using the port ftp/tnftpd
which is the same FTP server, but newer and might have more/better
functionality.
This results in us providing only one ftp daemon by default.
Reviewed by: bz
Approved by: imp (mentor, implicit)
MFC after: 3 days
Silence from: obrien
rtsol_interface gets reset to "yes" each time through the loop, but
rtsol_available does not. If a user has lo0 first in their list of
interfaces rtsol_available will get set to "no" the first time through
the loop and subsequent interfaces will not get rtsol'ed when they should.
Therefore change the conditional for the is_wired() test to _interface.
Noticed by: Dimitry Andric <dimitry@andric.com>
statically bind IPv4 <-> MAC address at boot time.
In order to use this, the administrator needs to configure the following
rc.conf(5) variable:
- static_arp_pairs: A list of names for static bind pairs, and,
- a series of static_arp_(name): the arguments that is being passed to
``arp -S'' operation.
Example:
static_arp_pairs="gw"
static_arp_gw="192.168.1.1 00:01:02:03:04:05"
See the rc.conf(5) manual page for more details.
Reviewed by: -rc@
MFC after: 2 weeks
AUTO the biggest mistake users made was leaving lo0 off the list. Since
lo0 is effectively mandatory, check for it and add it to the list if
it's not there.
simplify it a bit, and make use of that method to determine if an
interface is a candidate for IPv6 rtsol rather than listing all of the
possible wireless interfaces that should _not_ get rtsol'ed.
This change is only relevant for 8.0+ unless the "wlan mandatory" code
gets ported back to RELENG_7.
using freebsd-update. This applies to using freebsd-update in "upgrade
mode" and normal freebsd-update on a security branch.
The backup kernel will be written to /boot/kernel.old, if the directory
does not exist, or the directory was created by freebsd-update in a
previous backup. Otherwise freebsd-update will generate a new directory
name for use by the backup. By default symbol files are not backed up
to save diskspace and avoid filling up the root partition.
This feature is fully configurable in the freebsd-update config file,
but defaults to enabled.
MFC after: 1 week (stable/7)
Reviewed by: cperciva
Approved by: re (kib)
controllers. Controller, array, and drive status can be checked, basic
attributes can be changed, and arrays and spares can be created and deleted.
Controller firmware can also be flashed.
This does not replace MegaCLI, found in ports, as that is officially sanctioned
and supported by LSI and includes vastly more functionality. However, mfiutil
is open source and guaranteed to provide basic functionality, which can be
especially useful if you have a problem and can't get MegaCLI to work.
Approved by: re
Obtained from: Yahoo! Inc.
