sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
opt_device_polling.h
- Include opt_device_polling.h into appropriate files.
- Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that
can be compiled as loadable modules.
Reviewed by: bde
o Axe poll in trap.
o Axe IFF_POLLING flag from if_flags.
o Rework revision 1.21 (Giant removal), in such a way that
poll_mtx is not dropped during call to polling handler.
This fixes problem with idle polling.
o Make registration and deregistration from polling in a
functional way, insted of next tick/interrupt.
o Obsolete kern.polling.enable. Polling is turned on/off
with ifconfig.
Detailed kern_poll.c changes:
- Remove polling handler flags, introduced in 1.21. The are not
needed now.
- Forget and do not check if_flags, if_capenable and if_drv_flags.
- Call all registered polling handlers unconditionally.
- Do not drop poll_mtx, when entering polling handlers.
- In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx.
- In netisr_poll() axe the block, where polling code asks drivers
to unregister.
- In netisr_poll() and ether_poll() do polling always, if any
handlers are present.
- In ether_poll_[de]register() remove a lot of error hiding code. Assert
that arguments are correct, instead.
- In ether_poll_[de]register() use standard return values in case of
error or success.
- Introduce poll_switch() that is a sysctl handler for kern.polling.enable.
poll_switch() goes through interface list and enabled/disables polling.
A message that kern.polling.enable is deprecated is printed.
Detailed driver changes:
- On attach driver announces IFCAP_POLLING in if_capabilities, but
not in if_capenable.
- On detach driver calls ether_poll_deregister() if polling is enabled.
- In polling handler driver obtains its lock and checks IFF_DRV_RUNNING
flag. If there is no, then unlocks and returns.
- In ioctl handler driver checks for IFCAP_POLLING flag requested to
be set or cleared. Driver first calls ether_poll_[de]register(), then
obtains driver lock and [dis/en]ables interrupts.
- In interrupt handler driver checks IFCAP_POLLING flag in if_capenable.
If present, then returns.This is important to protect from spurious
interrupts.
Reviewed by: ru, sam, jhb
The FXP_SCR_FLOWCONTROL registers is at offset 0x19, but 2 bytes wide.
It cannot be read as a word without causing a panic on architectures
that enforce strict alignment.
MFC after: 3 days
that if softclock is running on another CPU and is blocked on our driver
lock, we will wait until it has acquired the lock, seen that it was
cancelled, dropped the lock, and awakened us so that we can safely destroy
the mutex.
MFC after: 3 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
the timeout routine.
- Fix locking in detach.
- Add locking in shutdown.
- Don't mess with the PCI command register in resume, the PCI bus driver
already does this for us.
- Add locking to the non-serial ifmedia routines.
- Fix locking in ioctl.
- Remove spls and support for 4.x.
MFC after: 1 week
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
latest 82550 and 82551 chipsets (revision IDs 0x0e, 0x0f and 0x10).
We were only enabling it for revisions 0x0c and 0x0d, now it's
enabled for any 8255x NIC with a revision ID bigger than 0x0c. It
should be safe, and this is what Intel does in their open source
driver.
MFC after: 2 weeks
Tested by: Pavel Lobach lobach_pavel at mail dot ru
from an mbuf into the fxp_encap() function, as done in other drivers.
- Don't waste time calling bus_dmamap_load_mbuf() if we know the mbuf
chain is too long to fit in a TX descriptor, call m_defrag() first.
- Convert fxp(4) to use bus_dmamap_load_mbuf_sg().
a vlan interface attached to a fxp(4) card when it has not been
initialized yet. We now set the links from our internel TX descriptor
structure to the TX command blocks at attach time rather than at init
time. While I'm here, slightly improve the style in fxp_attach().
PR: kern/78112
Reported by: Gavin Atkinson <gavin.atkinson@ury.york.ac.uk> and others
Tested by: flz, Gavin Atkinson <gavin.atkinson@ury.york.ac.uk>
MFC after: 1 week
testing it to know whether we should enable the 82503 serial mode...
Move code to the right location and disallow the use of the 82503
serial mode if the sc->revision field is 0 again. This makes fxp(4)
work correctly with ATMEL 350 93C46 cards (3 port 82559 based with a
82555 PHY), as well as with the older ATMEL 220 93C46 (same flavour)
and with the even older 10Mbps-only 82557 cards with the 82503 serial
interface.
Tested by: Andre Albsmeier <andrer@albsmeier.net>, krion
MFC after: 2 weeks
interface as well. This is not an expected revision id per the
datasheet, but unfortunately there are such cards out there with
a 82557 chipset, and they want to use the 82503.
PR: kern/75739
Reported by: Andre Albsmeier <andre.albsmeier@siemens.com>
datasheet says it is only valid for such chipsets and shouldn't be used
with others. This fixes some 82559 based cards which otherwise only
work at 10Mbit.
MFC after: 5 days
Tested by: krion
