A single gratuitous ARP (GARP) is always transmitted when an IPv4
address is added to an interface, and that is usually sufficient.
However, in some circumstances, such as when a shared address is
passed between cluster nodes, this single GARP may occasionally be
dropped or lost. This can lead to neighbors on the network link
working with a stale ARP cache and sending packets destined for
that address to the node that previously owned the address, which
may not respond.
To avoid this situation, GARP retransmissions can be enabled by setting
the net.link.ether.inet.garp_rexmit_count sysctl to a value greater
than zero. The setting represents the maximum number of retransmissions.
The interval between retransmissions is calculated using an exponential
backoff algorithm, doubling each time, so the retransmission intervals
are: {1, 2, 4, 8, 16, ...} (seconds).
Due to the exponential backoff algorithm used for the interval
between GARP retransmissions, the maximum number of retransmissions
is limited to 16 for sanity. This limit corresponds to a maximum
interval between retransmissions of 2^16 seconds ~= 18 hours.
Increasing this limit is possible, but sending out GARPs spaced
days apart would be of little use.
Submitted by: David A. Bright <david.a.bright@dell.com>
MFC after: 1 month
Relnotes: yes
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D7695
than removing the network interfaces first. This change is rather larger
and convoluted as the ordering requirements cannot be separated.
Move the pfil(9) framework to SI_SUB_PROTO_PFIL, move Firewalls and
related modules to their own SI_SUB_PROTO_FIREWALL.
Move initialization of "physical" interfaces to SI_SUB_DRIVERS,
move virtual (cloned) interfaces to SI_SUB_PSEUDO.
Move Multicast to SI_SUB_PROTO_MC.
Re-work parts of multicast initialisation and teardown, not taking the
huge amount of memory into account if used as a module yet.
For interface teardown we try to do as many of them as we can on
SI_SUB_INIT_IF, but for some this makes no sense, e.g., when tunnelling
over a higher layer protocol such as IP. In that case the interface
has to go along (or before) the higher layer protocol is shutdown.
Kernel hhooks need to go last on teardown as they may be used at various
higher layers and we cannot remove them before we cleaned up the higher
layers.
For interface teardown there are multiple paths:
(a) a cloned interface is destroyed (inside a VIMAGE or in the base system),
(b) any interface is moved from a virtual network stack to a different
network stack ("vmove"), or (c) a virtual network stack is being shut down.
All code paths go through if_detach_internal() where we, depending on the
vmove flag or the vnet state, make a decision on how much to shut down;
in case we are destroying a VNET the individual protocol layers will
cleanup their own parts thus we cannot do so again for each interface as
we end up with, e.g., double-frees, destroying locks twice or acquiring
already destroyed locks.
When calling into protocol cleanups we equally have to tell them
whether they need to detach upper layer protocols ("ulp") or not
(e.g., in6_ifdetach()).
Provide or enahnce helper functions to do proper cleanup at a protocol
rather than at an interface level.
Approved by: re (hrs)
Obtained from: projects/vnet
Reviewed by: gnn, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6747
There are number of radix consumers in kernel land (pf,ipfw,nfs,route)
with different requirements. In fact, first 3 don't have _any_ requirements
and first 2 does not use radix locking. On the other hand, routing
structure do have these requirements (rnh_gen, multipath, custom
to-be-added control plane functions, different locking).
Additionally, radix should not known anything about its consumers internals.
So, radix code now uses tiny 'struct radix_head' structure along with
internal 'struct radix_mask_head' instead of 'struct radix_node_head'.
Existing consumers still uses the same 'struct radix_node_head' with
slight modifications: they need to pass pointer to (embedded)
'struct radix_head' to all radix callbacks.
Routing code now uses new 'struct rib_head' with different locking macro:
RADIX_NODE_HEAD prefix was renamed to RIB_ (which stands for routing
information base).
New net/route_var.h header was added to hold routing subsystem internal
data. 'struct rib_head' was placed there. 'struct rtentry' will also
be moved there soon.
When using lagg failover mode neither Gratuitous ARP (IPv4) or Unsolicited
Neighbour Advertisements (IPv6) are sent to notify other nodes that the
address may have moved.
This results is slow failover, dropped packets and network outages for the
lagg interface when the primary link goes down.
We now use the new if_link_state_change_cond with the force param set to
allow lagg to force through link state changes and hence fire a
ifnet_link_event which are now monitored by rip and nd6.
Upon receiving these events each protocol trigger the relevant
notifications:
* inet4 => Gratuitous ARP
* inet6 => Unsolicited Neighbour Announce
This also fixes the carp IPv6 NA's that stopped working after r251584 which
added the ipv6_route__llma route.
The new behavour can be controlled using the sysctls:
* net.link.ether.inet.arp_on_link
* net.inet6.icmp6.nd6_on_link
Also removed unused param from lagg_port_state and added descriptions for the
sysctls while here.
PR: 156226
MFC after: 1 month
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D4111
sysctl and will always be on. The former split between default and
fast forwarding is removed by this commit while preserving the ability
to use all network stack features.
Differential Revision: https://reviews.freebsd.org/D4042
Reviewed by: ae, melifaro, olivier, rwatson
MFC after: 1 month
Sponsored by: Rubicon Communications (Netgate)
Both are used to protect access to IP addresses lists and they can be
acquired for reading several times per packet. To reduce lock contention
it is better to use rmlock here.
Reviewed by: gnn (previous version)
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D3149
function names have changed and comments are reformatted or added, but
there is no functional change.
Claim copyright for me and Adrian.
Sponsored by: Nginx, Inc.
represents a context.
- Preserve name 'struct igmp_ifinfo' for a new structure, that will be stable
API between userland and kernel.
- Make sysctl_igmp_ifinfo() return the new 'struct igmp_ifinfo', instead of
old one, which had a bunch of internal kernel structures in it.
- Move all above declarations from in_var.h to igmp_var.h, since they are
private to IGMP code.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Initially in_matrote() in_clsroute() in their current state was introduced by
r4105 20 years ago. Instead of deleting inactive routes immediately, we kept them
in route table, setting RTPRF_OURS flag and some expire time. After that, either
GC came or RTPRF_OURS got removed on first-packet. It was a good solution
in that days (and probably another decade after that) to keep TCP metrics.
However, after moving metrics to TCP hostcache in r122922, most of in_rmx
functionality became unused. It might had been used for flushing icmp-originated
routes before rte mutexes/refcounting, but I'm not sure about that.
So it looks like this is nearly impossible to make GC do its work nowadays:
in_rtkill() ignores non-RTPRF_OURS routes.
route can only become RTPRF_OURS after dropping last reference via rtfree()
which calls in_clsroute(), which, it turn, ignores UP and non-RTF_DYNAMIC routes.
Dynamic routes can still be installed via received redirect, but they
have default lifetime (no specific rt_expire) and no one has another trie walker
to call RTFREE() on them.
So, the changelist:
* remove custom rnh_match / rnh_close matching function.
* remove all GC functions
* partially revert r256695 (proto3 is no more used inside kernel,
it is not possible to use rt_expire from user point of view, proto3 support
is not complete)
* Finish r241884 (similar to this commit) and remove remaining IPv6 parts
MFC after: 1 month
with no RSS hash.
When doing RSS:
* Create a new IPv4 netisr which expects the frames to have been verified;
it just directly dispatches to the IPv4 input path.
* Once IPv4 reassembly is done, re-calculate the RSS hash with the new
IP and L3 header; then reinject it as appropriate.
* Update the IPv4 netisr to be a CPU affinity netisr with the RSS hash
function (rss_soft_m2cpuid) - this will do a software hash if the
hardware doesn't provide one.
NICs that don't implement hardware RSS hashing will now benefit from RSS
distribution - it'll inject into the correct destination netisr.
Note: the netisr distribution doesn't work out of the box - netisr doesn't
query RSS for how many CPUs and the affinity setup. Yes, netisr likely
shouldn't really be doing CPU stuff anymore and should be "some kind of
'thing' that is a workqueue that may or may not have any CPU affinity";
that's for a later commit.
Differential Revision: https://reviews.freebsd.org/D527
Reviewed by: grehan
enabled. This eliminates one mtx_lock() per each routing lookup thus improving
performance in several cases (routing to directly connected interface or routing
to default gateway).
Icmp redirects should not be used to provide routing direction nowadays, even
for end hosts. Routers should not use them too (and this is explicitly restricted
in IPv6, see RFC 4861, clause 8.2).
Current commit changes rnh_machaddr function to 'stock' rn_match (and back) for every
AF_INET routing table in given VNET instance on drop_redirect sysctl change.
This change is part of bigger patch eliminating rte locking.
Sponsored by: Yandex LLC
MFC after: 2 weeks
from scratch, copying needed functionality from the old implemenation
on demand, with a thorough review of all code. The main change is that
interface layer has been removed from the CARP. Now redundant addresses
are configured exactly on the interfaces, they run on.
The CARP configuration itself is, as before, configured and read via
SIOCSVH/SIOCGVH ioctls. A new prefix created with SIOCAIFADDR or
SIOCAIFADDR_IN6 may now be configured to a particular virtual host id,
which makes the prefix redundant.
ifconfig(8) semantics has been changed too: now one doesn't need
to clone carpXX interface, he/she should directly configure a vhid
on a Ethernet interface.
To supply vhid data from the kernel to an application the getifaddrs(8)
function had been changed to pass ifam_data with each address. [1]
The new implementation definitely closes all PRs related to carp(4)
being an interface, and may close several others. It also allows
to run a single redundant IP per interface.
Big thanks to Bjoern Zeeb for his help with inet6 part of patch, for
idea on using ifam_data and for several rounds of reviewing!
PR: kern/117000, kern/126945, kern/126714, kern/120130, kern/117448
Reviewed by: bz
Submitted by: bz [1]
- Remove ia_net, ia_netmask, ia_netbroadcast from struct in_ifaddr.
- Remove net.inet.ip.subnetsarelocal, I bet no one need it in 2011.
- fix bug when we were not forwarding to a host which matches classful
net address. For example router having 192.168.x.y/16 network attached,
would not forward traffic to 192.168.*.0, which are legal IPs in
CIDR world.
- For compatibility, leave autoguessing of mask based on class.
Reviewed by: andre, bz, rwatson
interface is brought down, even though the interface address is still
valid. This patch maintains the permanent ARP entries as long as the
interface address (having the same prefix as that of the ARP entries)
is valid.
Reviewed by: delphij
MFC after: 5 days
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
in_ifaddrhead and INADDR_HASH address lists.
Previously, these lists were used unsynchronized as they were effectively
never changed in steady state, but we've seen increasing reports of
writer-writer races on very busy VPN servers as core count has gone up
(and similar configurations where address lists change frequently and
concurrently).
For the time being, use rwlocks rather than rmlocks in order to take
advantage of their better lock debugging support. As a result, we don't
enable ip_input()'s read-locking of INADDR_HASH until an rmlock conversion
is complete and a performance analysis has been done. This means that one
class of reader-writer races still exists.
MFC after: 6 weeks
Reviewed by: bz
rather than pointers, requiring callers to properly dispose of those
references. The following routines now return references:
ifaddr_byindex
ifa_ifwithaddr
ifa_ifwithbroadaddr
ifa_ifwithdstaddr
ifa_ifwithnet
ifaof_ifpforaddr
ifa_ifwithroute
ifa_ifwithroute_fib
rt_getifa
rt_getifa_fib
IFP_TO_IA
ip_rtaddr
in6_ifawithifp
in6ifa_ifpforlinklocal
in6ifa_ifpwithaddr
in6_ifadd
carp_iamatch6
ip6_getdstifaddr
Remove unused macro which didn't have required referencing:
IFP_TO_IA6
This closes many small races in which changes to interface
or address lists while an ifaddr was in use could lead to use of freed
memory (etc). In a few cases, add missing if_addr_list locking
required to safely acquire references.
Because of a lack of deep copying support, we accept a race in which
an in6_ifaddr pointed to by mbuf tags and extracted with
ip6_getdstifaddr() doesn't hold a reference while in transmit. Once
we have mbuf tag deep copy support, this can be fixed.
Reviewed by: bz
Obtained from: Apple, Inc. (portions)
MFC after: 6 weeks (portions)
IPv4 stack.
Diffs are minimized against p4.
PCS has been used for some protocol verification, more widespread
testing of recorded sources in Group-and-Source queries is needed.
sizeof(struct igmpstat) has changed.
__FreeBSD_version is bumped to 800070.
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
but formerly missed under VIMAGE_GLOBAL.
Put the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.
Sponsored by: The FreeBSD Foundation
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
rt_check() in its original form proved to be sufficient and
rt_check_fib() can go away (as can its evil twin in_rt_check()).
I believe this does NOT address the crashes people have been seeing
in rt_check.
MFC after: 1 week
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
This particular implementation is designed to be fully backwards compatible
and to be MFC-able to 7.x (and 6.x)
Currently the only protocol that can make use of the multiple tables is IPv4
Similar functionality exists in OpenBSD and Linux.
From my notes:
-----
One thing where FreeBSD has been falling behind, and which by chance I
have some time to work on is "policy based routing", which allows
different
packet streams to be routed by more than just the destination address.
Constraints:
------------
I want to make some form of this available in the 6.x tree
(and by extension 7.x) , but FreeBSD in general needs it so I might as
well do it in -current and back port the portions I need.
One of the ways that this can be done is to have the ability to
instantiate multiple kernel routing tables (which I will now
refer to as "Forwarding Information Bases" or "FIBs" for political
correctness reasons). Which FIB a particular packet uses to make
the next hop decision can be decided by a number of mechanisms.
The policies these mechanisms implement are the "Policies" referred
to in "Policy based routing".
One of the constraints I have if I try to back port this work to
6.x is that it must be implemented as a EXTENSION to the existing
ABIs in 6.x so that third party applications do not need to be
recompiled in timespan of the branch.
This first version will not have some of the bells and whistles that
will come with later versions. It will, for example, be limited to 16
tables in the first commit.
Implementation method, Compatible version. (part 1)
-------------------------------
For this reason I have implemented a "sufficient subset" of a
multiple routing table solution in Perforce, and back-ported it
to 6.x. (also in Perforce though not always caught up with what I
have done in -current/P4). The subset allows a number of FIBs
to be defined at compile time (8 is sufficient for my purposes in 6.x)
and implements the changes needed to allow IPV4 to use them. I have not
done the changes for ipv6 simply because I do not need it, and I do not
have enough knowledge of ipv6 (e.g. neighbor discovery) needed to do it.
Other protocol families are left untouched and should there be
users with proprietary protocol families, they should continue to work
and be oblivious to the existence of the extra FIBs.
To understand how this is done, one must know that the current FIB
code starts everything off with a single dimensional array of
pointers to FIB head structures (One per protocol family), each of
which in turn points to the trie of routes available to that family.
The basic change in the ABI compatible version of the change is to
extent that array to be a 2 dimensional array, so that
instead of protocol family X looking at rt_tables[X] for the
table it needs, it looks at rt_tables[Y][X] when for all
protocol families except ipv4 Y is always 0.
Code that is unaware of the change always just sees the first row
of the table, which of course looks just like the one dimensional
array that existed before.
The entry points rtrequest(), rtalloc(), rtalloc1(), rtalloc_ign()
are all maintained, but refer only to the first row of the array,
so that existing callers in proprietary protocols can continue to
do the "right thing".
Some new entry points are added, for the exclusive use of ipv4 code
called in_rtrequest(), in_rtalloc(), in_rtalloc1() and in_rtalloc_ign(),
which have an extra argument which refers the code to the correct row.
In addition, there are some new entry points (currently called
rtalloc_fib() and friends) that check the Address family being
looked up and call either rtalloc() (and friends) if the protocol
is not IPv4 forcing the action to row 0 or to the appropriate row
if it IS IPv4 (and that info is available). These are for calling
from code that is not specific to any particular protocol. The way
these are implemented would change in the non ABI preserving code
to be added later.
One feature of the first version of the code is that for ipv4,
the interface routes show up automatically on all the FIBs, so
that no matter what FIB you select you always have the basic
direct attached hosts available to you. (rtinit() does this
automatically).
You CAN delete an interface route from one FIB should you want
to but by default it's there. ARP information is also available
in each FIB. It's assumed that the same machine would have the
same MAC address, regardless of which FIB you are using to get
to it.
This brings us as to how the correct FIB is selected for an outgoing
IPV4 packet.
Firstly, all packets have a FIB associated with them. if nothing
has been done to change it, it will be FIB 0. The FIB is changed
in the following ways.
Packets fall into one of a number of classes.
1/ locally generated packets, coming from a socket/PCB.
Such packets select a FIB from a number associated with the
socket/PCB. This in turn is inherited from the process,
but can be changed by a socket option. The process in turn
inherits it on fork. I have written a utility call setfib
that acts a bit like nice..
setfib -3 ping target.example.com # will use fib 3 for ping.
It is an obvious extension to make it a property of a jail
but I have not done so. It can be achieved by combining the setfib and
jail commands.
2/ packets received on an interface for forwarding.
By default these packets would use table 0,
(or possibly a number settable in a sysctl(not yet)).
but prior to routing the firewall can inspect them (see below).
(possibly in the future you may be able to associate a FIB
with packets received on an interface.. An ifconfig arg, but not yet.)
3/ packets inspected by a packet classifier, which can arbitrarily
associate a fib with it on a packet by packet basis.
A fib assigned to a packet by a packet classifier
(such as ipfw) would over-ride a fib associated by
a more default source. (such as cases 1 or 2).
4/ a tcp listen socket associated with a fib will generate
accept sockets that are associated with that same fib.
5/ Packets generated in response to some other packet (e.g. reset
or icmp packets). These should use the FIB associated with the
packet being reponded to.
6/ Packets generated during encapsulation.
gif, tun and other tunnel interfaces will encapsulate using the FIB
that was in effect withthe proces that set up the tunnel.
thus setfib 1 ifconfig gif0 [tunnel instructions]
will set the fib for the tunnel to use to be fib 1.
Routing messages would be associated with their
process, and thus select one FIB or another.
messages from the kernel would be associated with the fib they
refer to and would only be received by a routing socket associated
with that fib. (not yet implemented)
In addition Netstat has been edited to be able to cope with the
fact that the array is now 2 dimensional. (It looks in system
memory using libkvm (!)). Old versions of netstat see only the first FIB.
In addition two sysctls are added to give:
a) the number of FIBs compiled in (active)
b) the default FIB of the calling process.
Early testing experience:
-------------------------
Basically our (IronPort's) appliance does this functionality already
using ipfw fwd but that method has some drawbacks.
For example,
It can't fully simulate a routing table because it can't influence the
socket's choice of local address when a connect() is done.
Testing during the generating of these changes has been
remarkably smooth so far. Multiple tables have co-existed
with no notable side effects, and packets have been routes
accordingly.
ipfw has grown 2 new keywords:
setfib N ip from anay to any
count ip from any to any fib N
In pf there seems to be a requirement to be able to give symbolic names to the
fibs but I do not have that capacity. I am not sure if it is required.
SCTP has interestingly enough built in support for this, called VRFs
in Cisco parlance. it will be interesting to see how that handles it
when it suddenly actually does something.
Where to next:
--------------------
After committing the ABI compatible version and MFCing it, I'd
like to proceed in a forward direction in -current. this will
result in some roto-tilling in the routing code.
Firstly: the current code's idea of having a separate tree per
protocol family, all of the same format, and pointed to by the
1 dimensional array is a bit silly. Especially when one considers that
there is code that makes assumptions about every protocol having the
same internal structures there. Some protocols don't WANT that
sort of structure. (for example the whole idea of a netmask is foreign
to appletalk). This needs to be made opaque to the external code.
My suggested first change is to add routing method pointers to the
'domain' structure, along with information pointing the data.
instead of having an array of pointers to uniform structures,
there would be an array pointing to the 'domain' structures
for each protocol address domain (protocol family),
and the methods this reached would be called. The methods would have
an argument that gives FIB number, but the protocol would be free
to ignore it.
When the ABI can be changed it raises the possibilty of the
addition of a fib entry into the "struct route". Currently,
the structure contains the sockaddr of the desination, and the resulting
fib entry. To make this work fully, one could add a fib number
so that given an address and a fib, one can find the third element, the
fib entry.
Interaction with the ARP layer/ LL layer would need to be
revisited as well. Qing Li has been working on this already.
This work was sponsored by Ironport Systems/Cisco
Reviewed by: several including rwatson, bz and mlair (parts each)
Obtained from: Ironport systems/Cisco
and protocol-independent host mode multicast. The code is written to
accomodate IPv6, IGMPv3 and MLDv2 with only a little additional work.
This change only pertains to FreeBSD's use as a multicast end-station and
does not concern multicast routing; for an IGMPv3/MLDv2 router
implementation, consider the XORP project.
The work is based on Wilbert de Graaf's IGMPv3 code drop for FreeBSD 4.6,
which is available at: http://www.kloosterhof.com/wilbert/igmpv3.html
Summary
* IPv4 multicast socket processing is now moved out of ip_output.c
into a new module, in_mcast.c.
* The in_mcast.c module implements the IPv4 legacy any-source API in
terms of the protocol-independent source-specific API.
* Source filters are lazy allocated as the common case does not use them.
They are part of per inpcb state and are covered by the inpcb lock.
* struct ip_mreqn is now supported to allow applications to specify
multicast joins by interface index in the legacy IPv4 any-source API.
* In UDP, an incoming multicast datagram only requires that the source
port matches the 4-tuple if the socket was already bound by source port.
An unbound socket SHOULD be able to receive multicasts sent from an
ephemeral source port.
* The UDP socket multicast filter mode defaults to exclusive, that is,
sources present in the per-socket list will be blocked from delivery.
* The RFC 3678 userland functions have been added to libc: setsourcefilter,
getsourcefilter, setipv4sourcefilter, getipv4sourcefilter.
* Definitions for IGMPv3 are merged but not yet used.
* struct sockaddr_storage is now referenced from <netinet/in.h>. It
is therefore defined there if not already declared in the same way
as for the C99 types.
* The RFC 1724 hack (specify 0.0.0.0/8 addresses to IP_MULTICAST_IF
which are then interpreted as interface indexes) is now deprecated.
* A patch for the Rhyolite.com routed in the FreeBSD base system
is available in the -net archives. This only affects individuals
running RIPv1 or RIPv2 via point-to-point and/or unnumbered interfaces.
* Make IPv6 detach path similar to IPv4's in code flow; functionally same.
* Bump __FreeBSD_version to 700048; see UPDATING.
This work was financially supported by another FreeBSD committer.
Obtained from: p4://bms_netdev
Submitted by: Wilbert de Graaf (original work)
Reviewed by: rwatson (locking), silence from fenner,
net@ (but with encouragement)
structures. Detect when ifnet instances are detached from the network
stack and perform appropriate cleanup to prevent memory leaks.
This has been implemented in such a way as to be backwards ABI compatible.
Kernel consumers are changed to use if_delmulti_ifma(); in_delmulti()
is unable to detect interface removal by design, as it performs searches
on structures which are removed with the interface.
With this architectural change, the panics FreeBSD users have experienced
with carp and pfsync should be resolved.
Obtained from: p4 branch bms_netdev
Reviewed by: andre
Sponsored by: Garance A Drosehn
Idea from: NetBSD
MFC after: 1 month
goes away. Without this change, it leaks in_multi (and often ether_multi
state) if many clonable interfaces are created and destroyed in quick
succession.
The concept of this fix is borrowed from KAME. Detailed information about
this behaviour, as well as test cases, are available in the PR.
PR: kern/78227
MFC after: 1 week
may have changed by m_pullup() during fastforward processing.
While this is a bug it is actually never triggered in real world
situations and it is not remotely exploitable.
Found by: Coverity Prevent(tm)
Coverity ID: CID780
Sponsored by: TCP/IP Optimization Fundraise 2005
