IP fast forwarding, SIOCGIFADDR, setting hardware address (not currently
enabled in cm driver), multicasts (experimental)
- add ARC_MAX_DATA, use IF_HANDOFF, remove arc_sprintf() and some unused
variables
- if_simloop logic is made more similar to ethernet
- drop not ours packets early (if we are not in promiscous mode)
Submitted by: mark tinguely (partially)
Interface (SMAPI) BIOS, which is present on some IBM
Thinkpad models (560, 600, 770 to name a few.)
The SMAPI BIOS provides access to System Information,
System Configuration, and Power Management.
- Separate fc->dev (i.e. fwohci0) and fc->bdev (i.e. firewire0).
- Remove unused firewirebusreg.h.
- Reduce size of descriptor block for asynchronous transmit and
check the number of descriptor when copying from mbuf.
- Skip mbuf whose length is zero. NFS seems passing such mbuf and
some chips generates unrecoverable error.
module dependency system rely on linker behaviour that is machine dependent
and not part of the elf spec, and only work by accident on other platforms.
Approved by: re
the supported platforms. We build it into GENERIC, and it is currently
listed on the supported module list for drivers.conf on i386, which
breaks the release build. This may fix the release build for RC1 on
i386.
Conspiracy of: re
This code allows a user program to enable target mode on a SIM and
then emulate any number of devices (disks, tape drives, etc.) All
decisions about device behavior (UA, CA, inquiry response) are left
to the usermode program and the kernel driver is merely a conduit
for CCBs. This enables multiple concurrent target emulators, each
using its own backing store and IO model.
Also included is a user program that emulates a disk (RBC) using a
file as a backing store. This provides functionality similar to
md(4) at the CAM layer.
Code has been tested on ahc(4) and should also work on isp(4) (and
other SIMs that gain target mode support). It is a complete rewrite
of /sys/cam/scsi_target* and /usr/share/examples/scsi_target.
Design, comments from: gibbs
Supported by: Cryptography Research
Approved by: re
These makefiles work when building in the sys/modules directory, but
not with the objdir stuff that buildkernel uses. This is because they
used -I../../../blah rather than -I${.CURDIR}/../../../blah.
# I didn't fix the abuse of CFLAGS to specify -g since I wanted the
# barest minimal change since we're in a code freeze.
Approved by: make buildkernel...
Hat for armchair anarchists: core member fixing src tree damage
Has been seen to work on several cards and communicating with
several mobile phones to use them as modems etc.
We are still talking with 3com to try get them to allow us to include
the firmware for their pccard in the driver but the driver is here..
In the mean time
it can be downloaded from the 3com website and loaded using the utility
bt3cfw(8) (supplied) (instructions in the man page)
Not yet linked to the build
Submitted by: Maksim Yevmenkin <myevmenk@exodus.net>
Approved by: re
system accounting configuration and for nfsd server thread attach.
Policies might use this to protect the integrity or confidentiality
of accounting data, limit the ability to turn on or off accounting,
as well as to prevent inappropriately labeled threads from becoming nfs
server threads.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
is a compiler tool and needs to be compiled by the host compiler. I've
tested this in i386->sparc cross-build, 4.7->current upgrade, normal
buildkernel target, and normal /sys/i386/compile/GENERIC configurations.
Submitted by: ru
This is NOT YET CONVERTED TO -current.
This node is a source for preprogrammed packets at a known rate for testing.
I will convert it to -current "in place" but will MFC teh original
pre-conversion variant as that is what is originally submitted.
Man page my me, info from Dave's README.
Submitted by: Dave Chapeskie <dchapeskie@SANDVINE.com>
Obtained from: Sandvine inc.
MFC after: 1 week
These are really only partly netgraph nodes as they do not use the
netgraph interfaces for many of the functions for which they could
be used, however they represent important functionality.
Submitted by: wpaul
MFC after: 2 days
"refreshing" the label on the vnode before use, just get the label
right from inception. For single-label file systems, set the label
in the generic VFS getnewvnode() code; for multi-label file systems,
leave the labeling up to the file system. With UFS1/2, this means
reading the extended attribute during vfs_vget() as the inode is
pulled off disk, rather than hitting the extended attributes
frequently during operations later, improving performance. This
also corrects sematics for shared vnode locks, which were not
previously present in the system. This chances the cache
coherrency properties WRT out-of-band access to label data, but in
an acceptable form. With UFS1, there is a small race condition
during automatic extended attribute start -- this is not present
with UFS2, and occurs because EAs aren't available at vnode
inception. We'll introduce a work around for this shortly.
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
This policy can be loaded dynamically, and assigns each process a
partition number, as well as permitting processes to operate outside
the partition. Processes contained in a partition can only "see"
processes inside the same partition, so it's a little like jail.
The partition of a user can be set using the label mechanisms in
login.conf. This sample policy is a good starting point for developers
wanting to learn about how to produce labeled policies, as it labels
only one kernel object, the process credential.
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
This allocate the best IRQ to boot-disable devices (have IRQ 0).
Allocated IRQ will be used for PCI interrupt routing when ACPI is
enabled.
Note that verbose messaging enabled for the time being so that
people can easily notice the strange behavior if it happened.
aac driver dependent on the linux emulation module. This was
especially bad for the release engineers who tried to move the
aac driver from the kernel onto the drivers floppy. The linux
compat bits for this driver are now in their own driver, aac_linux.
It can be loaded as a module or compiled into the kernel. For
the latter case, the AAC_COMPAT_LINUX option is needed, along with
the COMPAT_LINUX option.
I've tested this in every configuration I can think of. This is an
MFC candidate for 4.7.
Idea from: rwatson
MFC after: 3 days
so that it is MI. Allow nfs_mountroot to return an error if the nfs_diskless
struct is not valid, rather than panicing later on. Call nfs_setup_diskless()
from nfs_mountroot if NFS_ROOT is defined, like bootpc_init(). Removed legacy
root mount support for sparc64, and enabled NFS_ROOT by default.
