(so we can see rapidly whether something was a fabric device but is
now gone).
Add a tag which says what role this adapter should take. It can take
on the value of None, Target, Initiator or Both. None is useful for
warm failover purposes. Remove the ISP_CFG_NOINIT silliness since
a role of "None" does this.
Add a isp_lastmbxcmd tag to store the opcode for the last mailbox
command used.
Module) and FBM (Fibre Buffer Modules). Also remember to clear the
semaphore registers. Tell the RISC processor to not halt on FPM
parity errors.
Throw out the ISP_CFG_NOINIT silliness and instead go to the use of
adapter 'roles' to see whether one completes initialization or not
(mostly for Fibre Channel). The ultimate intent, btw, of all of this
is to have a warm standby adapter for failover reasons. Because
we do roles now, setting of Target Capable Class 3 service parameters
in the ICB for the 2x00 cards reflects from role. Also, in isp_start,
if we're not supporting an initiator role, we bounce outgoing commands
with a Selection Timeout error. Also clean out the TOGGLE_TMODE
goop for FC- there is no toggling of target mode like there is
for parallel SCSI cards.
Do more cleanup with respect to using target ids 0..125 in F-port
topologies. Also keep track of things which *were* fabric devices
so that when you rescan the fabric you can notify the outer layers
when fabric devices go away.
Only force a LOGOUT for fabric devices if they're still logged in
(i.e., you cat their Port Database entry. Clean up the Get All Next
scanning.
Finally, use a new tag in the softc to store the opcode for the
last mailbox command used so we can report which opcode timed
out.
that require us to register our FC4 types of interest. Allow ourselves, in
F-port topologies, to start logging in fabric devices in the target 0..125
range. Change ISPASYNC_PDB_CHANGED (misnamed) to ISPASYNC_LOGGED_INOUT.
Fix (*SMACK*) again some default WWN stuff. This is *really* hard to get
right across all the range of platforms.
WWNs correctly (Again!) - this time for the case that we're not going
to fully init the adapter if isp_init is called (with ISP_CFG_NOINIT
set in options). The pupose for this is to bring the adapter up to
almost ready to go, get info out of NVRAM, but to not start it up- leaving
it until later to actually start things up if wanted (and possibly with
different roles selected).
Add a test against isp->isp_osinfo.islocked prior to trying to see
whether --isp->isp_osinfo.islocked is zero to cause us to unlock
(non-SMPLOCK case).
(specifically, how many entries we've looked at so far). Maintain
interrupt instrumentation. Use USEC_SLEEP instead of USEC_DELAY in
a number of places (this allows us to drop locks and sleep instead
of spin). Track changes to configuration options for topology preference.
Fix botched order of printout for Channel, Target, Lun.
compile time will build in mutex locks, otherwise the old locking (splcam/splx
with a recursion counter) will be compiled in.
We still depend on config_intr_hook to tell us when it's okay to call
msleep instead of polling. It'd be real nice if we could do this early
enough to not hang up a machine struggling with a bad Fibre Channel loop,
but that's still to come.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).
In order, from the top.....:
A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.
The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.
At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.
All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.
All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.
A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....
Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).
Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.
In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".
Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.
Various other cleanups.
isp_prt calls. We now use an argument to the ISPCTL_FCLINK_TEST
call. We change all IDPRINTF macros to isp_prt calls. We add
the isp_prt function here.
quite a bit so that all of the ports have a similar set of required
macros/definitions (and in similar places in the isp_<platform>.h
file).
Some new macros/functions added- Mailbox Acquire/Relase macros,
NANOTIME macros, SNPRINTf and STRNCAT. MemoryBarrier beomes
MEMORYBARRIER with much stronger types.
