ath9k does a few different things here during config - if it's an early
AR5416 with two chains, it enables all three chains for calibration and
then restores the chainmask to the original values after initial
calibration has completed.
The reason behind this commit is to begin breaking out the chainmask
configuration for this specific reason; follow-up commits will add
the chainmask restore in the ar5416Reset() routine.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
the completion schedule from the hardware and returns AH_TRUE if
the hardware supports multi-rate retries (AR5212 and above); and
returns AH_FALSE if the hardware doesn't support multi-rate retries.
The sample rate module directly reads the TX completion descriptor
and extracts the TX schedule information from that. It will be
updated in a future commit to instead use this method to determine
the completion schedule.
available today.
This card is a low power 802.11bgn that only does 11n rates up to MCS 7
(that's 65 Mbps in 20Mhz mode and 135 in 40Mhz mode).
802.11n is not yet supported, but will be in the future.
The driver still has a problem regarding to the setting of txpower on
the card, so don't expect good performance yet. After fixing this
problem, an MFC is possible.
Special thanks to iXsystems and S Smirnov <tonve at yandex.ru> for help
with the purchase of a netbook with this card.
Sponsored by: iXsystems, Inc.
o add 9280 attach that sets up ini, cal, etc.
o new rf backend for 9280 and later parts
o split ini setup and spur mitigation support out to methods
and provide 9280-specific support
o minor fixups to shared code to handle 9280-specific work
Obtained from: Atheros (ini values and some code)
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o add output mux support
o gpio pin count is chip-dependent
o 9280 and 9285 do input handling different
o hookup gpio interrupts
o no need to save/restore soft led state around reset
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>
Sponsored by: Carlson Wireless
