- Require the APIC enumerators to explicitly enable mixed mode by calling
ioapic_enable_mixed_mode(). Calling this function tells the apic driver
that the PC-AT 8259A PICs are present and routable through the first I/O
APIC via an ExtINT pin. The mptable enumerator always calls this
function for now. The MADT enumerator only enables mixed mode if the
PC-AT compatability flag is set in the MADT header.
- Allow mixed mode to be enabled or disabled via a 'hw.apic.mixed_mode'
tunable. By default this tunable is set to 1 (true). The kernel option
NO_MIXED_MODE changes the default to 0 to preserve existing behavior, but
adding 'hw.apic.mixed_mode=0' to loader.conf achieves the same effect.
- Only use mixed mode to route IRQ 0 if it is both enabled by the APIC
enumerator and activated by the loader tunable. Note that both
conditions must be true, so if the APIC enumerator does not enable mixed
mode, then you can't set the tunable to try to override the enumerator.
to map. If the checksum fails, the table is unmapped and a NULL pointer
returned.
- For ACPI version >= 2.0, check the extended checksum of the RSDP.
AcpiOsGetRootPointer() already checks the version 1.0 checksum.
- Remap the full MADT table at the end of madt_probe() so that we verify
its checksum before saying it is really there.
Requested by: njl
individual asm versions. The global lock is shared between the BIOS and
OS and thus cannot use our mutexes. It is defined in section 5.2.9.1 of
the ACPI specification.
Reviewed by: marcel, bde, jhb
host-PCI bridge device and find a valid $PIR.
- Make pci_pir_parse() private to pci_pir.c and have pir0's attach routine
call it instead of having legacy_pcib_attach() call it.
- Implement suspend/resume support for the $PIR by giving pir0 a resume
method that calls the BIOS to reroute each link that was already routed
before the machine was suspended.
- Dump the state of the routed flag in the links display code.
- If a link's IRQ is set by a tunable, then force that link to be re-routed
the first time it is used.
- Move the 'Found $PIR' message under bootverbose as the pir0 description
line lists the number of entries already. The pir0 line also only shows
up if we are actually using the $PIR which is a bonus.
- Use BUS_CONFIG_INTR() to ensure that any IRQs used by a PCI link are
set to level/low trigger/polarity.
active low polarity when using the PIC interrupt model. This should fix
broken SCI interrupts on machines when not using the APIC where the BIOS
doesn't program the ELCR to level trigger for the ACPI SCI.
Requested by: njl
polarity for a specified IRQ. The intr_config_intr() function wraps
this pic method hiding the IRQ to interrupt source lookup.
- Add a config_intr() method to the atpic(4) driver that reconfigures
the interrupt using the ELCR if possible and returns an error otherwise.
- Add a config_intr() method to the apic(4) driver that just logs any
requests that would change the existing programming under bootverbose.
Currently, the only changes the apic(4) driver receives are due to bugs
in the acpi(4) driver and its handling of link devices, hence the reason
for such requests currently being ignored.
- Have the nexus(4) driver on i386 implement the bus_config_intr() function
by calling intr_config_intr().
and intr_polarity enums for passing around interrupt trigger modes and
polarity rather than using the magic numbers 0 for level/low and 1 for
edge/high.
- Convert the mptable parsing code to use the new ELCR wrapper code rather
than reading the ELCR directly. Also, use the ELCR settings to control
both the trigger and polarity of EISA IRQs instead of just the trigger
mode.
- Rework the MADT's handling of the ACPI SCI again:
- If no override entry for the SCI exists at all, use level/low trigger
instead of the default edge/high used for ISA IRQs.
- For the ACPI SCI, use level/low values for conforming trigger and
polarity rather than the edge/high values we use for all other ISA
IRQs.
- Rework the tunables available to override the MADT. The
hw.acpi.force_sci_lo tunable is no longer supported. Instead, there
are now two tunables that can independently override the trigger mode
and/or polarity of the SCI. The hw.acpi.sci.trigger tunable can be
set to either "edge" or "level", and the hw.acpi.sci.polarity tunable
can be set to either "high" or "low". To simulate hw.acpi.force_sci_lo,
set hw.acpi.sci.trigger to "level" and hw.acpi.sci.polarity to "low".
If you are having problems with ACPI either causing an interrupt storm
or not working at all (e.g., the power button doesn't turn invoke a
shutdown -p now), you can try tweaking these two tunables to find the
combination that works.
IRQ is edge triggered or level triggered. For ISA interrupts, we assume
that edge triggered interrupts are always active high and that level
triggered interrupts are always active low.
- Don't disable an edge triggered interrupt in the PIC. This avoids
outb instructions to the actual PIC for traditional ISA IRQs such as
IRQ 1, 6, 14, and 15. (Fast interrupts such as IRQs 0 and 8 don't mask
their source, so this doesn't change anything for them.)
- For MCA systems we assume that all interrupts are level triggered and
thus need masking. Otherwise, we probe the ELCR. If it exists we trust
what it tells us regarding which interrupts are level triggered. If it
does not exist, we assume that IRQs 0, 1, 2, and 8 are edge triggered
and that all other IRQs are level triggered and need masking.
- Instruct the ELCR mini-driver to restore its saved state during resume.
register controlled the trigger mode and polarity of EISA interrupts.
However, it appears that most (all?) PCI systems use the ELCR to manage
the trigger mode and polarity of ISA interrupts as well since ISA IRQs used
to route PCI interrupts need to be level triggered with active low
polarity. We check to see if the ELCR exists by sanity checking the value
we get back ensuring that IRQS 0 (8254), 1 (atkbd), 2 (the link from the
slave PIC), and 8 (RTC) are all clear indicating edge trigger and active
high polarity.
This mini-driver will be used by the atpic driver to manage the trigger and
polarity of ISA IRQs. Also, the mptable parsing code will use this mini
driver rather than examining the ELCR directly.
interrupt source.
- Only do an outb() to the PIC to clear a bit in imen if the bit is set.
- Add a NUM_ISA_IRQS macro to replace uglier
'sizeof(array) / sizeof(member)' expressions along with a CTASSERT() to
ensure that the macro is correct.
than using legacy_pcib_attach(). The MP Table drivers don't use the $PIR,
and the legacy_pcib_attach() function probes and parses the $PIR in
addition to adding the pci bus child device.
parameter).
Keep using it only in the i386 NOTES for now. It is fairly MI, but it
doesn't use bus-space and has a couple of i386 i/o instructions in pci
intitialization.
correct interrupt source.
- Cache a pointer to the i8254_intsrc's pending method to avoid several
pointer indirections in i8254_get_timecount().
Reported by: bde
modules is a very nice way to produce hard-to-find panics. Who would look for
a bug in a Makefile anyway?
Has anyone seen the pointy hat? :-o
Approved by: njl (mentor)
gadgets (hotkeys, lcd, ...) on Asus laptops. I aim to closely track the
acpi4asus project which implements these features in the Linux kernel.
If this breaks your laptop, please let me know how it does it :-)
Approved by: njl (mentor)
there are a lot of other dependencies that preclude the kernel from
working). Instead, have a more generic note that isa should not be
removed. This should be less confusing for users.
different BIOSs use the same exact settings to mean two very different and
incompatible things for the SCI. Thus, if the SCI is remapped to a PCI
interrupt, we now trust the trigger/polarity that the MADT provides by
default. However, the SCI can be forced to level/lo as 1.10 did by setting
the tunable "hw.acpi.force_sci_lo" to a non-zero value from the loader.
Thus, if rev 1.10 caused an interrupt storm, it should nwo fix your
machine. If rev 1.10 fixed an interrupt storm on your machine, you
probably need to set the aforementioned tunable in /boot/loader.conf to
prevent the interrupt storm.
The more general problem of getting the SCI's trigger/polarity programmed
"correctly" (for some value of correctly meaning several workarounds for
broken BIOSs and inconsistent "implementations" of the ACPI standard) is
going to require more work, but this band-aid should improve the current
situation somewhat.
Requested by: njl
change the video output but use a separate device with a DSSX method
and a HID of "TOS6201" instead. We use a pseudo-driver to get the handle
for this object and pass it to the acpi_toshiba driver.
This is untested but seems to match the Linux Toshiba driver.
