At the moment grab and ungrab methods of all console drivers are no-ops.
Current intended meaning of the calls is that the kernel takes control of
console input. In the future the semantics may be extended to mean that
the calling thread takes full ownership of the console (e.g. console
output from other threads could be suspended).
Inspired by: bde
MFC after: 2 months
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
accessible:
(1) Always compile in support for breaking into the debugger if options
KDB is present in the kernel.
(2) Disable both by default, but allow them to be enabled via tunables
and sysctls debug.kdb.break_to_debugger and
debug.kdb.alt_break_to_debugger.
(3) options BREAK_TO_DEBUGGER and options ALT_BREAK_TO_DEBUGGER continue
to behave as before -- only now instead of compiling in
break-to-debugger support, they change the default values of the
above sysctls to enable those features by default. Current kernel
configurations should, therefore, continue to behave as expected.
(4) Migrate alternative break-to-debugger state machine logic out of
individual device drivers into centralised KDB code. This has a
number of upsides, but also one downside: it's now tricky to release
sio spin locks when entering the debugger, so we don't. However,
similar logic does not exist in other device drivers, including uart.
(5) dcons requires some special handling; unlike other console types, it
allows overriding KDB's own debugger selection, so we need a new
interface to KDB to allow that to work.
GENERIC kernels in -CURRENT will now support break-to-debugger as long as
appropriate boot/run-time options are set, which should improve the
debuggability of BETA kernels significantly.
MFC after: 3 weeks
Reviewed by: kib, nwhitehorn
Approved by: re (bz)
already supported nested PICs, but was limited to having a nested
AT-PIC only. With G5 support the need for nested OpenPIC controllers
needed to be added. This was done the wrong way and broke the MPC8555
eval system in the process.
OFW, as well as FDT, describe the interrupt routing in terms of a
controller and an interrupt pin on it. This needs to be mapped to a
flat and global resource: the IRQ. The IRQ is the same as the PCI
intline and as such needs to be representable in 8 bits. Secondly,
ISA support pretty much dictates that IRQ 0-15 should be reserved
for ISA interrupts, because of the internal workins of south bridges.
Both were broken.
This change reverts revision 209298 for a big part and re-implements
it simpler. In particular:
o The id() method of the PIC I/F is removed again. It's not needed.
o The openpic_attach() function has been changed to take the OFW
or FDT phandle of the controller as a second argument. All bus
attachments that previously used openpic_attach() as the attach
method of the device I/F now implement as bus-specific method
and pass the phandle_t to the renamed openpic_attach().
o Change powerpc_register_pic() to take a few more arguments. In
particular:
- Pass the number of IPIs specificly. The number of IRQs carved
out for a PIC is the sum of the number of int. pins and IPIs.
- Pass a flag indicating whether the PIC is an AT-PIC or not.
This tells the interrupt framework whether to assign IRQ 0-15
or some other range.
o Until we implement proper multi-pass bus enumeration, we have to
handle the case where we need to map from PIC+pin to IRQ *before*
the PIC gets registered. This is done in a similar way as before,
but rather than carving out 256 IRQs per PIC, we carve out 128
IRQs (124 pins + 4 IPIs). This is supposed to handle the G5 case,
but should really be fixed properly using multiple passes.
o Have the interrupt framework set root_pic in most cases and not
put that burden in PIC drivers (for the most part).
o Remove powerpc_ign_lookup() and replace it with powerpc_get_irq().
Remove IGN_SHIFT, INTR_INTLINE and INTR_IGN.
Related to the above, fix the Freescale PCI controller driver, broken
by the FDT code. Besides not attaching properly, bus numbers were
assigned improperly and enumeration was broken in general. This
prevented the AT PIC from being discovered and interrupt routing to
work properly. Consequently, the ata(4) controller stopped functioning.
Fix the driver, and FDT PCI support, enough to get the MPC8555CDS
going again. The FDT PCI code needs a whole lot more work.
No breakages are expected, but lackiong G5 hardware, it's possible
that there are unpleasant side-effects. At least MPC85xx support is
back to where it was 7 months ago -- it's amazing how badly support
can be broken in just 7 months...
Sponsored by: Juniper Networks
