messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
Move the declaration of freerq() to request.h.
logrq: add support for lock events.
vinumstart: solve a problem where removing a plex from an active
volume could cause attempts to access non-existent plexes.
launch_requests: don't set a request group active until we're sure we
can launch it. This caused some hangs under unusual
circumstances.
bre: don't set XFR_BAD_SUBDISK if we're not going to use it.
build_read_request: correct recovery, which caused some hangs under
(other) unusual circumstances.
build_rq_buffer: don't set bp->b_dev if we don't have a dev.
sdio: clean up, remove obsolete code.
deallocrqg: unlock any locks the rqg may have.
bre5:
Shorten some lines.
Desired-by: bde
If we're reading from a short plex, return EOF indication.
Always lock the stripe before starting a transfer. Hopefully the
current version will solve some data integrity problems that have
been reported with degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
solve some data integrity problems that have been reported with
degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Tidy other comments.
open_drive: don't call set_drive_state if we decide to take it down.
This could help avoid some race conditions with the daemon.
init_drive: don't set the drive down, we'll let close_locked_drive do
that.
close_locked_drive: set drive state to down without calling
set_drive_state. This could help avoid some race conditions with the
daemon.
driveio: remove the function, it wasn't being used.
get_volume_label: remove volume dependencies so that we can return a
label for plexes and subdisks as well. What a kludge.
Remove declarations for freerq and free_rqg.
Remove DEBUG_RESID code.
freerq: check whether the request is holding a lock, free if so.
free_rqg: remove. It wasn't being used any more.
Change the Debugger calls to panics.
checkdiskconfig(): remove. It didn't make any sense to complain about
kernel keywords in user config files; it just made it more difficult
to convert. Now we ignore kernel keywords if we're not in kernel
mode.
get_empty_sd: initialize sectors.
free_drive: don't close if we don't have a vp. Maybe this will help
fix the problem that peter had, but I wouldn't count on it.
config_plex: If the plex is RAID-5, give it a rangelock structure.
start_config: Reset current drive, plex and volume so that a new
'create' command doesn't get long-dead defaults.
struct rqelement, enum rqinfo_type, struct rqinfo, union rqinfou: add
lock requests.
Add declarations for freerq and unlockrange. Since they include
request structures, they can't go in vinumext.h
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
- %q -> %ll.
Fixed nearby errors not reported by gcc -Wformat on i386's:
- don't assume that the promotion of [u_]int64_t is [u_]quad_t.
- don't use signed formats for unsigned args.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
update_plex_state:
If any subdisk in the plex is initializing, set the plex to
initializing state. This gets rid of the ugly corrupt/degraded/up
transitions which previously occurred.
Desired-by: Steve Taylor <staylor@cybernet.com>
sddownstate:
Add new function, used by checksdstate.
checksdstate:
Let sddownstate decide what status to return.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
logrq: save device major and minor numbers to compensate for lost
dev_t.
launch_requests: Don't issue requests which are marked
XFR_BAD_SUBDISK. This may make things easier in bre().
bre:
Rearrange.
- Change some comments
- Recognize holes in plex structure. Formerly this could lead to
incorrect write to the plex. Return REQUEST_DEGRADED on a read
request, but carry on to the bitter end on a write request, and
mark the requests for the inaccessible subdisks with
XFR_BAD_SUBDISK.
- return REQUEST_EOF if the requested transfer goes beyond the end
of the plex. This is not an error, since other plexes may go
further into the volume address space.
build_read_request:
Handle REQUEST_DEGRADED returned from bre().
sdio:
Lock buffer before issuing the requests.
will only accept partitions of type 'vinum'.
format_config: Use the new %q format option in kvprintf, thus getting
rid of some of the filthiest code I've written in a long time. Also
remove the lltoa() function.
With-great-thanks-to: peter
format_config: Accept the fact that a subdisk might not be attached to
a plex, and save the config correctly.
vinum_scandisk: Scan all slices on a drive with a Microsoft partition
table. Only look at the compatibility slice if nothing was found in
the Microsoft slices.
This change removes a frequently employed method of shooting
yourself in the foot: people would decide that the Vinum drives
belonged on their own slice, and they wouldn't be able to start the
subsystem after a reboot. Documentation updates to follow.
initialize subdisks. Probably the plex-related subdisk type will die
a death.
vinumconfig.c:
Accept (and ignore) kernel state information in userland config
files. This saves a lot of error recovery and also makes it possible
to use the output of printconfig to create new configuration.
Remove checkdiskconfig(). It wasn't needed any more.
Start adding support for hot spare drives. You can't put anything on
them (yet).
Change message formats from %lld to %qd.
get_empty_sd: Initialize size to -1. Previously this was done in
config_subdisk, which is the wrong place.
start_config: set current drive, plex and volume to -1, thus stopping
update configurations from taking their defaults from old configs.
now used in f_ops in place of NULL, and modifications to the files
are more carefully ordered. f_ops should also be set to &badfileops
upon "close" of a file.
This does not fix other problems mentioned in this PR than the first
one.
PR: 11629
Reviewed by: peter
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
the device numbers are now minor number only, so that we can still
compare them after dev_t has turned into a blob.
Broken-by: dev_t changes
Reported-by: Vallo Kallaste <vallo@matti.ee>
"Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
by removing a floppy that as being operated on.
The spagghetti is hardly understandable at all anymore, so i can't
100 % ascertain this is really the Right Thing to do, maybe our new
floppy driver maintainer, Jesus Monroy Jr can do this. :-))
The structure is the right length, but some of the members (notably
wi_q_info) were off a bit. This causes the received signal strength
values to appear bogus.
vnodes referencing this device.
Details:
cdevsw->d_parms has been removed, the specinfo is available
now (== dev_t) and the driver should modify it directly
when applicable, and the only driver doing so, does so:
vn.c. I am not sure the logic in checking for "<" was right
before, and it looks even less so now.
An intial pool of 50 struct specinfo are depleted during
early boot, after that malloc had better work. It is
likely that fewer than 50 would do.
Hashing is done from udev_t to dev_t with a prime number
remainder hash, experiments show no better hash available
for decent cost (MD5 is only marginally better) The prime
number used should not be close to a power of two, we use
83 for now.
Add new checkalias2() to get around the loss of info from
dev2udev() in bdevvp();
The aliased vnodes are hung on a list straight of the dev_t,
and speclisth[SPECSZ] is unused. The sharing of struct
specinfo means that the v_specnext moves into the vnode
which grows by 4 bytes.
Don't use a VBLK dev_t which doesn't make sense in MFS, now
we hang a dummy cdevsw on B/Cmaj 253 so that things look sane.
Storage overhead from all of this is O(50k).
Bump __FreeBSD_version to 400009
The next step will add the stuff needed so device-drivers can start to
hang things from struct specinfo
interrupts that were scheduled. Testing shows it didn't really do very much
and it makes the code a little more complicated (which is never a good thing).
Also fix the rambuffer offset initialization for the 512K/64K SRAM case
(512K total using 64K chips). It should be 0. The only case with a
non-standard rambuffer offset address is 1024K/64K according to the
SysKonnect manual. (My card has the 1024/64 configuration and I don't know
which card uses the 512/64 configuration, if any, so I'm not sure that
this was really a problem for anyone.)
Change number of VBI lines from 16 to 12 for NTSC formats.
Juha.Nurmela@quicknet.inet.fi found/fixed bug in VBI_SLEEP.
New features
MSP3430G DBX initialisation from Matt Brown <matt@dqc.org>
STB Bt878 card identification.
Hauppauge Model Number identification.
Changes to probeCard() for better eeprom identification.
Experimental TDA9850 initialisation code, from Linux bttv.
Cross Platform Changes
The driver has been reorgainsed based ideas from Brad Parker's port to Linux
to seperate OS Dependant and Independant sections.
I have backends for FreeBSD 2.2.x/3.x and 4.x newbus, BSDI, OpenBSD and NetBSD.
This commit has FreeBSD 2.2.8/2.2-stable/3.x and FreeBSD 4.x newbus backends.
Some code submitted by: Juha.Nurmela@quicknet.inet.fi
Matt Brown <matt@dqc.org>
Brad Parker <brad@parker.boston.ma.us>
Some code obtained from: Linux bttv driver
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
- Correctly observe the variable `extra_history_size' when changing
the size of history (scroll back) buffer.
- Added sc_free_history_buffer().
Pointed out by: des
in ti_rxeof() instead. This doesn't really seem to provide much in the
way of a performance boost, and I'm pretty sure it can cause mbuf leakage
in some extreme cases.
frames (or just insane received packet lengths generated due to errors
reading from the NIC's internal buffers). Anything too large to fit
safely into an mbuf cluster buffer is discarded and an error logged.
I have not observed this problem with my own cards, but on user has
reported it and adding the sanity test seems reasonable in any case.
Problem noted and patch provided by: Per Andersson <per@cdg.chalmers.se>
isp_io_map, isp_no_fwload, isp_fwload, isp_no_nvram, isp_fcduplex
which are all bitmaps of isp instances that should or shouldn't
map memory space, I/O space, not load f/w, load f/w, ignore nvram,
not ignore nvarm, set full duplex mode. Also have an isp_seed value
that we can use to generate a pseudo seed for a synthetic WWN.
Other minor cosmetic cleanup. Add in support for the Qlogic ISP
2200. Very important change where we actually check now to see
whether we were successful in mapping request and response queues
(and fibre channel scratch space).
not having SCSI_ISP_SCCLUN config defined if we don't have f/w for
the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change
the way the default LoopID is gathered (it's now a platform specific
define so that some attempt at a synthetic WWN can be made in case
NVRAM isn't readable).
Change initialization of options a bit- don't use ADISC. Set
FullDuplex mode if config options tells us to do so. Do not use
FULL_LOGIN after LIP- it's the right thing to do but it causes too
much loop disruption (Loop Resets). Sanity check some default
values. Redo construction of port and node WWNs based upon what we
have- if we have 2 in the top nibble, we can have distinct port
and node WWNs. Clean up some SCCLUN related code that we obviously
had never compiled (:-(). Audit commands coming int ispscsicmd and
don't throw commands at Fibre devices that do not have Class 3
service parameters TARGET ROLE defined.
Clean up f/w initialization a bit. Add Fabric support (or at least
the first blush of it). Whew - way too much to describe here.
Basically, after a LIP, hang out until we see a Loop Up or a Port
DataBase Change async event, then see if we're on a Fabric
(GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric
controller for fabric devices using the GetAllNext SNS subcommand.
As we find devices, announce them to the outer layer. Try and do
some guard code for broken (Brocade) SNS servers (that get stuck
in loops- gotta maybe do this a different way using the GP_ID3 cmd
instead). Then do a scan of the lower (local loop) ids using a
GET_PORT_NAME to see if the f/w has logged into anything at that
loop id. If so, then do a GET_PORT_DATABASE command. Do this scan
into a local database. At this point we can say the loop is 'Ready'.
After this, we merge our local loop port database with our stored
port database- in a as yet to be really fully exercised fashion we
try and follow the logic of something having moved around. The
first time we see something at a Loop ID, we fix it, for the purpose
of this system instance, at that Loop ID. If things shift around
so it ends up somewhere else, we still keep it at this Loop ID (our
'Target') but use the new (moved) Loop ID when we actually throw
commands at it. Check for insane cases of different Loop IDs both
claiming to have the same WWN- if that happens, invalidate both.
Notify the outer layer of devices that have arrived and devices
that have gone away. *Finally*, when this is done, search the
softc's database of Fabric devices and perform logout/login actions.
The Qlogic f/w maintains logout/login for all local loop devices.
We have to maintain logout/login for fabric devices- total PITA.
Expect to see this area undergo more change over time.
Change some fcp parameter structures such that we can get the portid
(24 bit value), get both node and port WWN, know whether we're on a fabric
or not, note whether we've ever seen the loop up, and note the current
state of the loop.
Replace the isp_pdb_t structure in fcparams with a reduced cost structure
that maintains a static relationship to 'Target', but can have the actual
loop ID used change (in case, post LIP, we discover things have moved
around). This also retains portid and node/port WWNs. This array gets
larger if we have fabric support compiled in.
Note special loop IDs that are invariate for this device- FL_PORT_ID
(0x7e) which tells us if there's a fabric controller present, FC_PORT_ID
and FC_SNS_ID (fabric controller port and fabric SNS server port). We don't
use the latter two for anything. IDs above FC_SNS_ID up through 255 are
available for mapping fabric devices to 'target' ids.
Add in a config define to set FC full duplex mode. Add in a define to
recognize the Qlogic 2200 boards. Add comments about ISPCTL commands.
Add and change some ISPASYNC enumes.
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
Correct race condition between caller and daemon.
Tripped-over-by: Zach Heilig <zach@uffdaonline.net>
Bernd Walter <ticso@cicely.de>
Niels Chr. Bank-Pedersen <ncbp@bank-pedersen.dk>
lockmgr locks. This commit should be functionally equivalent to the old
semantics. That is, all buffer locking is done with LK_EXCLUSIVE
requests. Changes to take advantage of LK_SHARED and LK_RECURSIVE will
be done in future commits.
The atapi subsystem has gotten better error handeling and timeouts,
it also tries a REQUEST SENSE command when devices returns errors,
to give a little more info as to what went wrong. It might be a
little verbose for now, but I'm interested in as much feedback on
errors as possible, especially timeouts, as I'm a bit in doubt if
I've chosen resonable default values everywhere.
The disk driver has been changed a bit to prepare for tagged queing,
which is next on my list.
The disk driver has grown a dump routine, I got one implementation
from Darrell Anderson <anderson@cs.duke.edu> which also did
partial dumps (usefull on big memory machines) I left out the
partial stuff for now, and changed the rest alot to fit into the new
ad_request framework.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
and insertion should affect the line the cursor is on only.
This change should have been committed together with syscons.c rev 1.308.
(I forgot to do so, when I committed syscons.c :-(
Pointed out by: sos
If the drive goes down, queue a close to the daemon. In many cases
this function gets called in process context, so it could do it
directly, but it's more trouble finding out where we came from than
getting the daemon to do it.
Don't bzero the buffer structure, it's been done already by
allocrqg.
sdio:
Build up a correct buffer header, don't steal linkages from system
buffer headers.
Noticed-by: mckusick
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
fix; it doesn't address the problem of removing the module. If you do
the following:
vinum stop
fsck /dev/vinum/VOLUME
you *will* get a system crash. What we need is a cdevsw_remove
corresponding to cdevsw_add, but that hasn't been written yet.
Submitted-by: phk
usbd_get_interface_descriptor
2) remove soft reset. It's been dropped from the USB Mass Storage Bulk-Only
Specification
3) move the clear feature halt to the reset routine.
positively not let ti_encap() fill up the TX ring all the way and wrap
around. This fixes a potential transmit lockup where a really fast
machine (or particular TX traffic pattern) can overrun the end of the
ring.
Reported by: John Plevyak <jplevyak@inktomi.com>
Also removed the BSDI support (for now)
This allows the driver to be loaded/unloaded as a KLD
and loaded in the boot loader phase whithout making a custom kernel.
corresponding variable `rc_wakeup_started' in rev.1.36 but broken
again in rev.1.37. This bug only caused excessive polling (it gave
NRC activations for each of the SWI handler and the timeout handler
instead of 1 of each).
Moved cdevsw attachment from the driver probe routine to the driver
attach routine.
via an IBM PCI-PCI bridge (82351 or 82352 or 82353)
The driver must identify if it is on a secondary PCI bus, which is
created via the IBM PCI-PCI bridge. If it is, then it must initialise
the IBM PCI-PCI bridge correctly.
To do this, the following new functions are added.
Because they use the pcici_t tag, they are considered 2.2 compatibility APIs
pcici_t * pci_get_parent_from_tag(pcici_t tag);
int pci_get_bus_from_tag(pcici_t tag);
(The _from_tag suffix is used to prevent clashes with similarly named
newbus PCI API functions)
Submitted by: Anton Berezin <tobez@plab.ku.dk>
Reviewed by: Doug Rabson <dfr@nlsystems.com>
Reworked by: Me (roger)
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
of the current interrupt trasaction.
- Do not schedule the next interrupt transaction if the pipe is being
aborted or the last round of the interrupt transaction ended with error.
Submitted by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
- Call ums_disable() to abort the pipe.
- Do not wake up processes which has been waiting or polling for mouse
data. It won't be available anymore.
Submitted by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
disable_intr() does non-recursive locking in the SMP case. This should
fix cy-driver-related panics when SMP is configured.
Broken in: rev.1.73 (3.1 and -current)
Allow chipset drivers to specify the direct-mapped DMA window's mask in
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
Reviewed by: Doug Rabson <dfr@nlsystems.com>
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
These changes should not affect the i386 port
Reviewed by: Doug Rabson <dfr@nlsystems.com>
only support 'mirroring' the vendor and device ids, so we don't
lose any information. Certain revisions of the aic7880 will not
perform the mirroring so to match all possiblities would double
the number of table entries. This change also allows us to match
things like the 2944B which I missed in the original table.
commands are outstanding. You'd think they'd just clear the IDLE bit,
but alas, no. Delay until all pending mailbox commands have completed
in aha_cmd to work around this.
Report sync rates correctly on Fast Adaptec cards. Clones may still be
reported incorrectly since there is no documenation on how they report
extended sync values.
Clean up some unused fields in the aha softc.
SIS/VIA/ OPTi chipset PCI bus workarounds.
These make the Bt878/879 chips stabler on certain
older and non-intel motherboards.
Use options BKTR_430_FX_MODE
or options BKTR_SIS_VIA_MODE
to enable these modes.
Also rename 849 to 849A
in the transmit code: the TX descriptor ring, and a 'shadow' ring of mbuf
pointers, one for each TX descriptor. When transmitting a packet that
consists of several fragments in an mbuf chain, we link each fragment
to a descriptor in the TX ring, but we only save a pointer to the mbuf
chain. This pointer is saved in the shadow ring entry which corresponds
to the first fragment in the packet. Later, ti_txeof() can release the
whole chain with a single m_freem() call. (We need the second ring to
keep track of the virtual addresses of the mbuf chains.)
The problem with this is that the Tigon isn't actually through with the
mbuf chain until it reaches the last fragment (which has the TI_BDFLAG_END
bit set), however the current scheme releases the mbuf chain as soon as
the first fragment is consumed. This is wrong, since the mbufs can then
be yanked out from under the Tigon and modified before the other fragments
can be transmitted.
The fix is to make a one line change to ti_encap() so that it saves the
mbuf chain pointer in the shadow ring entry that corresponds to the last
fragment in TX ring instead of the first. This prevents the mbufs from
being released until the last fragment is transmitted.
Painstakingly diagnosed and fixed by: Robert Picco <picco@mail.wevinc.com>
Brought to my attention by: dg
manager and prevented IOPort allocation beyond the first EISA slot from
working. subr_rman.c should have trapped this on the way into the system
rather than tripping over the wreckage.
Head banged into wall repeatedly by: "Matthew N. Dodd" <winter@jurai.net>
