allocation, as required.
If m_getm() receives NULL as a first argument, then it allocates `len'
(second argument) bytes worth of mbufs + clusters and returns the chain
only if it was able to allocate everything.
If the first argument is non-NULL, then it should be an existing mbuf
chain (e.g. pre-allocated mbuf sitting on a ring, on some list, etc.) and
so it will allocate `len' bytes worth of clusters and mbufs, as needed,
and append them to the tail of the passed in chain, only if it was able
to allocate everything requested.
If allocation fails, only what was allocated by the routine will be freed,
and NULL will be returned.
Also, get rid of existing m_getm() in netncp code and replace calls to it
to calls to this new generic code.
Heavily Reviewed by: bp
clear MCPCIA_INT_MASK0 helps things substantially. So, why not indeed?
Rearrange irq and cookie calculation to use shifts/masks instead
of division. Fix things to correctly remember the intpin for that
one in a million non-INTA PCI device.
made no sense in the context of wrapping them within the _SYBRIDGE macro-
or anything like it- so we concluded that this must have been a typo
in the docs. This also doesn't use the same bridge offset as anything
else.
Add some defines for the INT_CTL register.
address is configured on a interface. This is useful for routers with
dynamic interfaces. It is now possible to say:
0100 allow tcp from any to any established
0200 skipto 1000 tcp from any to any
0300 allow ip from any to any
1000 allow tcp from 1.2.3.4 to me 22
1010 deny tcp from any to me 22
1020 allow tcp from any to any
and not have to worry about the behaviour if dynamic interfaces configure
new IP numbers later on.
The check is semi expensive (traverses the interface address list)
so it should be protected as in the above example if high performance
is a requirement.
run-time. This is temporary solution until proper kernel Unicode interfaces
are in place and as such was purposely designed to be as tiny as possible
(3 lines of the code not counting comments). The port with conversion routines
for the most popular single-byte languages will be added later today
Reviewed by: bp, "Michael C . Wu" <keichii@iteration.net>
Approved by: bp
one the number of variables needed for top and other setgid kmem
utilities that could only be accessed via /dev/kmem previously.
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: freebsd-audit
- All processes go into the same array of queues, with different
scheduling classes using different portions of the array. This
allows user processes to have their priorities propogated up into
interrupt thread range if need be.
- I chose 64 run queues as an arbitrary number that is greater than
32. We used to have 4 separate arrays of 32 queues each, so this
may not be optimal. The new run queue code was written with this
in mind; changing the number of run queues only requires changing
constants in runq.h and adjusting the priority levels.
- The new run queue code takes the run queue as a parameter. This
is intended to be used to create per-cpu run queues. Implement
wrappers for compatibility with the old interface which pass in
the global run queue structure.
- Group the priority level, user priority, native priority (before
propogation) and the scheduling class into a struct priority.
- Change any hard coded priority levels that I found to use
symbolic constants (TTIPRI and TTOPRI).
- Remove the curpriority global variable and use that of curproc.
This was used to detect when a process' priority had lowered and
it should yield. We now effectively yield on every interrupt.
- Activate propogate_priority(). It should now have the desired
effect without needing to also propogate the scheduling class.
- Temporarily comment out the call to vm_page_zero_idle() in the
idle loop. It interfered with propogate_priority() because
the idle process needed to do a non-blocking acquire of Giant
and then other processes would try to propogate their priority
onto it. The idle process should not do anything except idle.
vm_page_zero_idle() will return in the form of an idle priority
kernel thread which is woken up at apprioriate times by the vm
system.
- Update struct kinfo_proc to the new priority interface. Deliberately
change its size by adjusting the spare fields. It remained the same
size, but the layout has changed, so userland processes that use it
would parse the data incorrectly. The size constraint should really
be changed to an arbitrary version number. Also add a debug.sizeof
sysctl node for struct kinfo_proc.
not be retried. It is an indication that there was an error that was
corrected during the execution of the command. This is per ANSI SCSI2
spec.
It's possible that these should also be noted to the console (as indicative,
perhaps, of growing media defect lists in drives), but the default of
printing errors out if bootverbose in this case is probably enough.
Also, there'd been a missing ERESTART for that clause anyway.
2. If you have an ABORTED COMMAND, it's almost invariably a SCSI parity
error. You should never be silent about these since users should do something
about this if it occurs (moving that power cord *away* from the SCSI cable is
always a good first start). This should print irrespective of bootverbose
because it's an actual real error even if we retry a transmission.
Reviewed by: audit@freebsd.org, gibbs@freebsd.org
- Missing cpu_to_scr() added (endian-ness).
Improvement (fix|workaroung??):
- Blindly firing a PPR can lead to some messy situations due to
various causes or misfeatures, for example:
* The 53C1010-[33|66] supports offset 62 in DT mode, but only
offset 31 in ST mode. As a result, a PPR(DT, offset 62)
responded with PPR(ST, any offset > 31) must be rejected.
* A device that doesn't know about PPR should reject it, but
may also be confused by this message.
When a PPR encounters problems, the driver now patches the goal
transfer settings for legacy negotiations to be performed later
with the offending target. This give a chance for bad situations
to be fixed automagically.
Some things needed bits of <i386/include/lock.h> - cy.c now has its
own (only) copy of the COM_(UN)LOCK() macros, and IMASK_(UN)LOCK()
has been moved to <i386/include/apic.h> (AKA <machine/apic.h>).
Reviewed by: jhb
were performed to determine if the received packet should be reset. This
created erroneous ratelimiting and false alarms in some cases. The code
has now been reorganized so that the checks for validity come before
the call to badport_bandlim. Additionally, a few changes in the symbolic
names of the bandlim types have been made, as well as a clarification of
exactly which type each RST case falls under.
Submitted by: Mike Silbersack <silby@silby.com>
and function argument declarations. Make sure that functions that are
supposed to return a pointer return NULL in case of failure. Don't cast
NULL. Finally, get rid of annoying `register' uses.
isp_iid_set/isp_iid for fibre channel- this is because we now
fake a port database entry for ourselves. Add the additional loop
states between LOOP_PDB_RCVD and LOOP_READY.
Change and comment on a wad of Fibre Channel isp_control functions.
Change and comment on some of the ISPASYNC Fibre Channel events.
the unit number doesn't get reused.
Make sure that if we've compiled for ISP_TARGET_MODE we set the
default role to be ISP_ROLE_INITIATOR|ISP_ROLE_TARGET.
Do some misc other cleanups.
and depending on role, make sure link is up, scan the fabric (if we're
connected to a fabric), scan the local loop (if appropriate), merge
the results into the local port database then, check once again
to make sure we have f/w at FW_READY state and the the loopstate
is LOOP_READY.
Comment out usage of ISP_SMPLOCK- I have my doubts that this works sanely
as yet because CAM itself still needs Giant. I *was* dropping my lock
and grabbing Giant when doing the upcall for completion, but this is all
seems ridiculous until CAM is fixed.
if we're ISP_ROLE_NONE. Change ISPASYNC_LOGGED_INOUT to ISPASYNC_PROMENADE.
Make sure we note if something is a fabric device.
Target mode:
Finally fix (to a first approximation) SCSI Target Mode again- we needed
to correctly check against CAM_TARGET_WILDCARD and CAM_LUN_WILDCARD
so that targbh won't confuse us. Comment out the drainqueue stuff for
now. Use isp_fc_runstate instead if isp_control/ISPCTL_FCLINK_TEST.
Remove ISP2100_FABRIC defines- we always handle fabric now. Insert
isp_getmap helper function (for getting Loop Position map). Make
sure we (for our own benefit) mark req_state_flags with RQSF_GOT_SENSE
for Fibre Channel if we got sense data- the !*$)!*$)~*$)*$ Qlogic
f/w doesn't do so. Add ISPCTL_SCAN_FABRIC, ISPCTL_SCAN_LOOP, ISPCTL_SEND_LIP,
and ISPCTL_GET_POSMAP isp_control functions. Correctly send async notifications
upstream for changes in the name server, changes in the port database, and
f/w crashes. Correctly set topology when we get a ASYNC_PTPMODE event.
Major stuff:
Quite massively redo how we handle Loop events- we've now added several
intermediate states between LOOP_PDB_RCVD and LOOP_READY. This allows us
a lot finer control about how we scan fabric, whether we go further
than scanning fabric, how we look at the local loop, and whether we
merge entries at the level or not. This is the next to last step for
moving managing loop state out of the core module entirely (whereupon
loop && fabric events will simply freeze the command queue and a thread
will run to figure out what's changed and *it* will re-enable the queu).
This fine amount of control also gets us closer to having an external
policy engine decide which fabric devices we really want to log into.
tracing in order to avoid duplication.
- Insert some tracepoints back into the mutex acq/rel code, thus ensuring
that we can trace all lock acq/rel's again.
- All CURPROC != NULL checks are MPASS()es (under MUTEX_DEBUG) because they
signify a serious mutex corruption.
- Change up some KASSERT()s to MPASS()es, and vice-versa, depending on the
type of problem we're debugging (INVARIANTS is used here to check that
the API is being used properly whereas MUTEX_DEBUG is used to ensure that
something general isn't happening that will have bad impact on mutex
locks).
Reminded by: jhb, jake, asmodai
genassym here, but what I've also noticed is that we're dorking
with a mutex directly at assembler level- I'm not sure that this
is wise at this stage in the SMP port- I think it's going to be much
safer for a while to do things in C until SMP wunderkind figure out
what works and slow down this 3 order differential...
Style nits.
Make sure that our selection hardware is disabled
as soon as possible after detecting a busfree and
even go so far as to disable the selection hardware
in advance of an event that will cause a busfree
(ABORT or BUS DEVICE RESET message). The concern
is that the selection hardware will select a target
for which, after processing the bus free, there
will be no commands pending. The sequencer idle
loop will re-enable the selection should it still be
necessary.
In ahc_handle_scsiint(), clear SSTAT0 events several
PCI transactions (most notably reads) prior to clearing
SCSIINT. The newer chips seem to take a bit of time to
see the change which can make the clearing of SCSIINT
ineffective.
Don't bother panicing at the end of ahc_handle_scsiint().
Getting to the final else just means we lost the race
with clearing SCSIINT.
In ahc_free(), handle init-level 0. This can happen when we
fail the attach for RAID devices. While I'm here, also kill
the parent dma tag.
In ahc_match_scb(), consider initiator ccbs to be any
that are not from the target mode group. This fixes
a bug where an external target reset CCB was not getting
cleaned up by the reset code.
Don't bother freezing a ccb in any of our "abort" routines
when the status is set to CAM_REQ_CMP. This can happen
for a target reset ccb.
aic7xxx.reg:
Reserve space for a completion queue. This will be used
to enhance performance in the near future.
aic7xxx.seq:
Remove an optimization for the 7890 autoflush bug that
turned out to allow, in rare cases, some data to get
lost.
Implement a simpler, faster, fix for the PCI_2_1 retry
bug that hangs the sequencer on an SCB dma for certain chips.
Test against SAVED_SCSIID rather than SELID during target
reselections. This is how we always did it in the past,
but the code was modified while trying to work around an
issue with the 7895. SAVED_SCSIID takes into account
twin channel adapters such as the 2742T, whereas SELID
does not have the channel bit. This caused invalid
selection warnings and other strangeness on these cards.
aic7xxx_pci.c
Use the correct mask for checking the generic aic7892
entry.
it as I was playing with some other ways of doing kernel preemption.
You must still specify the PREEMPTION option in your config file to get a
preemptive kernel.
