into one function syscons_configure_keyboard(). Call new function from
both syscons_start() and sysconst_setkeyboard(). The reason for this
is because syscons_start() will (re)configure both keyboard and screen
settings. Apparently, some graphics cards have problems with running
vidcontrol(1) while X11 is running.
Remove "/etc/rc.d/syscons restart" from /etc/devd.conf. It is no longer
required. Using "/etc/rc.d/syscons setkeyboard" is enough. This also
should fix annoying "syscons not running?" message.
Tested by: Ulrich Spoerlein < q at galgenberg dot net >
MFC after: 3 days
keyboard device name (i.e. /dev/kbd0). This method will do nothing is
kbdmux(4) is the current active keyboard, otherwise it will switch
active keyboard as requested.
Modify ukbd(4) entries in the /etc/devd.conf to use /etc/rc.d/syscons
and new 'setkeyboard' method.
No comments from: freebsd-current@
MFC after: 1 day
way interfaces are configured. Some key points:
- At startup, all interfaces are configured through /etc/rc.d/netif.
- ifconfig_<if> variables my now mix real ifconfig commands the with
DHCP and WPA directives. For example, this allows media
configuration prior to running dhclient.
- /etc/rc.d/dhclient is not run at startup except by netif to start
dhclient on specific interfaces.
- /etc/pccard_ether calls "/etc/rc.d/netif start <if>" to do most of
it's work.
- /etc/pccard_ether no longer takes additional arguments to pass to
ifconfig. Instead, ifconfig_<if> variables are now honored in favor
of pccard_ifconfig when available.
- /etc/pccard_ether will only run on interfaces specified in
removable_interfaces, even if pccard_ifconfig is set.
- add udav(4)
In the scsi-controller-regex:
- correct an entry
- move another one to the right place
- add a bunch of missing drivers
Glanced at by: trhodes (scsi-controller-regex part)
MFC after: 3 days
adapters from usbd.conf to devd.conf. USB ethernet devices were
already handled in devd.conf so this just removes their usbd.conf
entry.
PR: conf/73799
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
it is still above the critical temperature on the next poll cycle. This
is a 10 second advance notice by default. Document the private
(non-standard) notify we will be using with devd(8).
the throttling state in response to line transitions. Future plans
include adding support for CPU frequency changes.
Add a devd.conf entry for calling this script.
The default values for this are:
performance_cx_lowest="HIGH" # Use HLT (C0) online
performance_throttle_state="HIGH" # 100% (no throttling)
economy_cx_lowest="LOW" # Use the lowest Cx state possible
economy_throttle_state="HIGH" # 100% (no throttling)
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
