This is done by misusing the device minor a bit to encode the
track no there.
So to read track #4 just use /dev/acdNt4 where N is the device #.
The driver no automatically sets the blocksize (sectorsize) to
what the track is set to in the TOC.
This has the nice effect that you can now rip audioi tracks
by simply doing:
dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352
it cant be much simpler than that :)
NOTE: the original acdNa & acdNc device still work as usual,
except the blocksize is set according to track0.
from the SCSI id it has. (this avoids the confusing umass-sim32 device. It
should have been umass-sim0 all along (there is only one), and if it is
spoken to as a SCSI device the sim should be umass32.
Make the rescan actually work. We need to fill in a target and lun wildcard
and not the SCSI id of the SIM.
Add a seatbelt.
position, channel 1's dma position register must be quiescent. So
the driver will spl, pause the DMA, delay a bit and hold as still as
possible while snapping the picture.
I'm sure there HAS to be a better way to do this, but if there is, it's
not documented.
So far as I can tell, this fixes recording, which means the Solo is open
for business.
cases the registers are not correctly set on resume.
This solves the problem of USB failing after resuming a machine.
Submitted by: mike+fbsd@medianstrip.net
PR: 18261
Promise Ultra100 / Fasttrak100
HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100)
Intel ICH2 (Intel 815E based motherboards)
So far I can read >90MB/s on the Promise and the HPT370.
I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems
writing is still done in ATA66 mode :(
The ICH2 support is untested as of yet...
modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
the scratch RAM for data normally found in the SEEPROM (presumably in the
event that the SEEPROM is unavailable or can't be read). This code causes
a spontaneous reboot on monster.osd.bsdi.com, which has an embedded aic7880
controller. The problem appears to happen either when it writes to the
SCBPTR port and then reads from the SCB_CONTROL port. Somewhere during
the inb/outb operations, the system has a heart attack and restarts.
This code looks very suspicious, particularly since it has unconditionalized
debug mesages such as "Got here!" and "And it even worked!". With this
block #ifdef'ed out, the machine boots and runs properly. I stronly suggest
that it stay #ifdef'ed out until it's properly tested.
opens if the reference count is not decremented on close.
Note that this may result in the reference count being corrupted
on full duplex devices (due to mismatching opens/closes), but the
code doesn't use the reference count for anything on full duplex
devices.
2. Offer half duplex with both playback and record on channel 1 or
full duplex with playback always on channel 2 as a compile-time option.
3. 16 bit record output is byte swapped for some dumb reason. Report the _BE
AFMTs for recording.
if you kldload this driver, all the subordinate devices are probed/attached
as expected. But this is not the case when the driver is statically compiled
into the kernel. Since I do most of my testing with modules, I failed to
notice this. I'm not sure if it's intended behavior or not. I think it may
be, but it seems a little counter-intuitive.
16 bit samples have some sort of choppiness, the nature of which
is not completely clear, but it clearly has something to do with
dma buffer synchronization. But at least channel 1 makes noise now.
appears to be the correct length, but quality of output has not yet
been tested. Also, full duplex audio (that is, playback on channel 1)
does not yet work. Two constants and I am there!
Obtained from: major hints from ALSA
with LEDs on some cards being stomped on when clearing the "jabber disable"
bit. Using DC_SETBIT() has an unwanted side effect of setting a write enable
bit in the watchdog timer register which we really want to be cleared when
we do a write.
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).
In order, from the top.....:
A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.
The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.
At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.
All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.
All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.
A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....
Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).
Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.
In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".
Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.
Various other cleanups.
isp_prt calls. We now use an argument to the ISPCTL_FCLINK_TEST
call. We change all IDPRINTF macros to isp_prt calls. We add
the isp_prt function here.
quite a bit so that all of the ports have a similar set of required
macros/definitions (and in similar places in the isp_<platform>.h
file).
Some new macros/functions added- Mailbox Acquire/Relase macros,
NANOTIME macros, SNPRINTf and STRNCAT. MemoryBarrier beomes
MEMORYBARRIER with much stronger types.
isp2100_fw_statename as an INLINE (now a function in isp.c). Remove
isp2100_pdb_statename (unused). Redo all ISP_SCSI_XFER_T as XS_T types.
Change all RQUEST_QUEUE_LEN/RESULT_QUEUE_LEN macros to take a parameter.
Add isp_print_bytes function.
Disable "cache line streaming" for aic7890/91 Rev A chips. I
have never seen these chips fail using this feature, but
some of Adaptec's regression tests have.
Explicitly set "cache line streaming" to on for aic7896/97
chips. This was happening before, but this documents the
fact that these chips will not function correctly without
CACHETHEEN set.
aic7xxx.h:
Add new bug types.
Fix a typo in a comment.
aic7xxx.reg:
Add a definition for the SHVALID bit in SSTAT3 for Ultra2/3
chips. This bit inicates whether the bottom most (current)
element in the S/G fifo has exhausted its data count.
aic7xxx.seq:
Be more careful in how we turn off the secondary DMA channel.
Being less careful may hang the PCI bus arbitor that negotiates
between the two DMA engines.
Remove an unecessary and incorrect flag set operation in
the overrun case.
On Ultra2/3 controllers, clear the dma FIFO before starting
to handle an overrun. We don't want any residual bytes from
the beginning of the overrun to cause the code that shuts
down the DMA engine from hanging because the FIFO is not
(and never will be) empty.
If the data fifo is empty by the time we notice that a
read transaction has completed, there is no need to
hit the flush bit on aic7890/91 hardware that will not
perform an auto-flush. Skip some cycles by short circuiting
the manual flush code in this case.
When transitioning out of data phase, make sure that we
have the next S/G element loaded for the following
reconnect if there is more work to do. The code
would do this in most cases before, but there was
a small window where the current S/G element could
be exhausted before our fetch of the next S/G element
completed. Since the S/G fetch is already initiated
at this point, it makes sense to just wait for the
segment to arrive instead of incuring even more latency
by canceling the fetch and initiating it later.
Fast path the end of data phase handling for the last
S/G segment. In the general case, we might have
worked ahead a bit by stuffing the S/G FIFO with
additional segments. If we stop before using them
all, we need to fixup our location in the S/G stream.
Since we can't work past the last S/G segment, no
fixups are ever required if we stop somewhere in
that final segment.
Fix a little buglet in the target mode dma bug handler.
We were employing the workaround in all cases instead
of only for the chips that require it.
Fix the cause of SCB timeouts and possible "lost data"
during read operations on the aic7890. When sending
a data on any Ultra2/3 controller, the final segment
must be marked as such so the FIFO will be flushed and
cleaned up correctly when the transfer is ended. We
failed to do this for the CDB transfer and so, if
the target immediately transfered from command to data
phase without an intervening disconnection, the first
segment transferred would be any residual bytes from
the cdb transfer. The Ultra160 controllers for some
reason were not affected by this problem.
Many Thanks to Tor Egge for bringing the aic7890 problem
to my attention, providing analysis, as well as a mechanism
to reproduce the problem.
stored at a different location in the PCI space, so adjust accordingly.
Also, when using more than two smart controllers in one machine, the
disks were assigned the wrong drive number; fix this as well.
the 12.4.11 firmware with a few changes to the link handling code merged
in from the 12.4.13 release. I'm doing this because the 12.4.13 firmware
doesn't seem to handle 10/100 link settings properly on 1000baseT cards.
Note that the revision codes still identify the firmware as 12.4.13
because both ti_fw2.h and ti_fw.h have to have the same revision values,
and I wanted to keep the 12.4.13 firmware for Tigon 1 cards.
It's nice to have firmware source.
wrong bytes.
o Improve the public interface; use void* instead of char* or u_int64_t
to pass arbitrary data around.
Submitted by: kris ("horrible bug")
didn't bother to send a saved data pointers after the last transfer,
is not recorded in sgptr. This was only a problem if the target
reported non-zero status as we always check the residual in that case.
Correct the BUILD_TCL macro. It was placing the target id
in the wrong bits. This was only an issue for adapters that
do not perform SCB paging (aha-3940AUW for instance).
Don't bother inlining ahc_index_busy_tcl. It is never
used in a performance critical path and is a bit chunky.
Correct ahc_index_busy_tcl to deal with "busy target tables"
embedded in the latter half of 64byte SCBs.
Don't initialize the busy target table to its empty state
until after we have finished extracting configuration
information from chip SRAM. In the common case of using
16 bytes of chip SRAM to do untagged target lookups,
we were trashing the last 8 targets configuration data.
(actually only target 8 because of the bug in the
BUILD_TCL macro).
Cram the "bus reset delivered" message back under bootverbose.
Fix the cleanup of the SCB busy target table when aborting
commands. If the lun is wildcarded, we must loop through
all possible luns.
aic7xxx.h:
Only bother supporting 64 luns right now. It doesn't seem
like either this driver or any peripherals will be doing
information unit transfers (where the lun number is a
32 bit integer) any time soon.
aic7xxx.seq:
Fix support for the aic7895. We must flush the data
FIFO if performing a manual transfer that is not
a multiple of 8 bytes. We were doing this quite
regularly for embedded cdbs.
Manaually flush the fifo on earlier adapters when
dealing with embedded cdbs too. We were stuffing
the FIFO with 16 bytes instead, but triggering
the flush is more efficient and allows us to
remove two instructions from the "copy_to_fifo"
routine.
o Make the comments KNF-compliant.
o Use nanotime instead of getnanotime; the manpage lies about the
kern.timecounter.method - it has been removed.
o Fix the ENTROPYSOURCE const permanently.
o Make variable names more consistent.
o Make function prototypes more consistent.
Some more needs to be done; to follow.
cards. This basically involves switching to the 12.4.13 firmware, plus
a couple of minor tweaks to the driver.
Also changed the jumbo buffer allocation scheme just a little to avoid
'failed to allocate jumbo buffer' conditions in certain cases.
support for relocating the port address if the isa hints specify a
different address from the address the chipset currently has.
Submitted by: Andrew M. Miklic <miklic@ibm.net>
lock up under moderate to heavy load.
The status & command fields share a 32-bit longword. The programming
API of the eepro apparently requires that you update the command field
of a transmit slot that you've already given to the card. This means
the card could be updating the status field of the same longword at
the same time. Since alphas can only operate on 32-bit chunks of
memory, both the status & command fields are loaded from memory &
operated on in registers when the following line of C is executed:
sc->cbl_last->cb_command &= ~FXP_CB_COMMAND_S;
The race is caused by the card DMA'ing up the status at just the wrong
time -- after it has been loaded into a register & before it has been
written back. The old value of the status is written back, clobbering
the status the card just DMA'ed up. The fact that the card has sent
this frame is missed & the transmit engine appears to hang.
Luckily, as numerous people on the freebsd-alpha list pointed out, the
load-locked/store-conditional instructions used by the atomic
functions work with respect changes in memory due to I/O devices. We
now use them to safely update the command field.
Tested by: Bernd Walter <ticso@mail.cicely.de>
errors that plagued those cards with XFree86 4.0. They have two memory
ranges as well as an IO port range to them. Also cleaned up the three
warning messages that I got, from inb(), outb() and linuxulator. Also, I
noticed that the DRI and Glide support for the Voodoo4 and 5 has been
placed upon linux.3dfx.com, too bad they haven't released the tech docs
yet. Apparently, they are still pushing glide for all of us, so I will try
and add support once those tech docs are up.
other systems.
o Normalize copyright text.
o Clean up probe code function interfaces by passing around a single
structure of common arguments instead of passing "too many" args
in each function call.
o Add support for the AAA-131 as a SCSI adapter.
o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net
o Correct manual termination support for PCI cards. The bit definitions
for manual termination control in the SEEPROM were incorrect.
o Add support for extracting NVRAM information from SCB 2 for BIOSen
that use this mechanism to pass this data to OS drivers.
o Properly set the STPWLEVEL bit in PCI config space based on the
setting in an SEEPROM.
o Go back to useing 32byte SCBs for all controllers. The current
firmware allows us to embed 12byte cdbs on all controllers in
a 32byte SCB, and larger cdbs are rarely used, so it is a
better use of this space to offer more SCBs (32).
o Add support for U160 transfers.
o Add an idle loop executed during data transfers that prefetches
S/G segments on controllers that have a secondary DMA engine
(aic789X).
o Improve the performance of reselections by avoiding an extra
one byte DMA in the case of an SCB lookup miss for the reselecting
target. We now keep a 16byte "untagged target" array on the card
for dealing with untagged reselections. If the controller has
external SCB ram and can support 64byte SCBs, then we use an
"untagged target/lun" array to maximize concurrency. Without
external SCB ram, the controller is limited to one untagged
transaction per target, auto-request sense operations excluded.
o Correct the setup of the STPWEN bit in SXFRCTL1. This control
line is tri-stated until set to one, so set it to one and then
set it to the desired value.
o Add tagged queuing support to our target role implementation.
o Handle the common cases of the ignore wide residue message
in firmware.
o Add preliminary support for 39bit addressing.
o Add support for assembling on big-endian machines. Big-endian
support is not complete in the driver.
o Correctly remove SCBs in the waiting for selection queue when
freezing a device queue.
o Now that we understand more about the autoflush bug on the
aic7890, only use the workaround on devices that need it.
o Add a workaround for the "aic7890 hangs the system when you
attempt to pause it" problem. We can now pause the aic7890
safely regardless of what instruction it is executing.
allocate a short port range in some alpha configurations.
Submitted by: "Andrew M. Miklic" <miklic@udlkern.fc.hp.com>,
Mark Abene <phiber@radicalmedia.com>
when we're done reading it (makes checking things easier).
Before calling isp_notify_ack make sure we're at RUNSTATE-
elsewise we can be responding to LIPs or SCSI bus resets
before we've finished some of the wiring.
we need a function that tells the Qlogic f/w that a target mode command
is done, so increase the resource count for that lun. Add in a timeout
function to kick the putback again if we fail to do it the first time (we
may not have the request queue space for ATIO push). Split the function
isp_handle_platform_ctio into two parts so that the timeout function for
the ATIO push or isp_handle_platform_ctio can inform CAM that the requested
CTIO(s) are now done.
Clean up (cough) residual handling. What we need for Fibre Channel
is to preserve the at_datalen field from the original incoming ATIO
so we can calculate a 'true' residual. Unfortunately, we're not
guaranteed to get that back from CAM. We'll *try* to find it hiding
in the periph_priv field (layering violation)- but if an ATIO was
passed in from user land- forget it. This means that we'll probably
get residuals wrong for Fibre Channel commands we're completing
with an error. It's too late to 4.1 release to fix this- too bad.
Luckily the only device we'd really care about this occurring on
is a tape device and they're still so rare as FC attached devices
that this can be considered an untested combination anyway.
Remove all CCINCR usage (resource autoreplenish). When we've proved
to ourself that things are working properly, we can add it back
in.
Make sure we propage 'suggested' sense data from the incoming ATIO
into the created system ATIO- and set sense_len appropriately.
Correctly propagate tag values.
Fall back to the model of generating (well, the functions in isp_pci.c
do the work) multiple CTIOs based upon what we get from XPT. Instead
of being able to pair Qlogic generated ATIOs with CAM ATIOs, and then
to pair CAM CTIOs with Qlogic CTIOs, we have to take the CTIO passed
to us from XPT, and if it implies that we have to generate extra
Qlogic CTIOs, so be it. This means that we have to wait until the
last CTIO in a sequence we generated completes before calling xpt_done.
Executive summary- target mode actually now pretty much works well
enough to tell folks about.
