the module is built-in to the kernel then the kldunload will fail. Rather
than do this just check if there are rules and then remove them all.
Add requirement on FILESYSTEMS to ensure /usr is present for /usr/sbin/ugidfw
and /usr/bin/xargs. This was already effectively the ordering from rcorder(8).
MFC after: 2 weeks
Relnotes: yes
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
setups that worked before, flip the default to "YES". Most people don't
have /etc/rctl.conf, so they won't be affected in any way.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
This is being done to fix breakage with make distribution with read-only
source trees as make distribution doesn't use make obj like building
tests/ does in all cases
Reported by: Wolfgang Zenker <wolfgang@lyxys.ka.sub.org>
Suggested by: jhb
X-MFC with: r282059
MFC after: 1 week
devd.conf execution of third-party software, that needs libraries
from /usr/local. Since devd is launched before ldconfig script, if
the hardware that has associated software is attached on boot, then
execution would fail.
Differential Revision: https://reviews.freebsd.org/D2332
Reviewed by: imp
- Remove extranious echo that breaks puppet
- Handle restarts of multiple pflog devices correctly
- Add the ability to perform actions on specific pflog devices.
PR: 199150
Submitted by: jason.unovitch@gmail.com
MFC after: 3 days
r272959 broke compatibility with mfsBSD that stores the default network
config file in /etc/rc.conf.d/network. In order to fix that load the network
config file from netif also.
This was a discrepancy between ^/projects/building-blocks and ^/head that I
didn't resolve before committing the change to ^/head
Pointyhat to: me
Reported by: jhb
MFC after: 20 days
X-MFC with: r278249
Sponsored by: EMC / Isilon Storage Division
and IPv6 rules in a single table. ipf -6 -Fa will flush the whole table,
including IPv4 rules. This patch removes the redundant ipf -I -6 -Fa
statement.
PR: 188318
MFC after: 2 weeks
mrouted has been available in ports for the last 8 years as net/mrouted . An
equivalent rc.d script has been present in the port.
Remove all corresponding variables from etc/defaults/rc.conf
Relnotes: yes
- bootparamd
- bootpd
- finger/fingerd
- ftp/ftpd
- hastctl/hastd
- iscsid, et al
- rbootd
- talk/talkd
- tcpd, et al
- tftp/tftpd
Add src.conf entries for the various components and do a best effort
at adding components to tools/build/mk/OptionalObsoleteFiles.inc
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
random script ran before filesystems were mounted, which is no
longer the case.
In random_start(), immediately delete each file that is fed into
/dev/random, and recreate the default entropy file immediately
after reading and deleting it. The logic used in random_stop()
to determine which file to write to should probably be factored
out and used here as well.
do not require additional entropy to function.
It would create a circular dependency (not immediately obvious:
geli provides 'disks' and requires 'random' as of r273872,
'random' requires 'FILESYSTEMS', 'FILESYSTEMS' requires 'root',
'root' requires 'swap', and finally 'swap' requires 'disk').
This code has had an extensive rewrite and a good series of reviews, both by the author and other parties. This means a lot of code has been simplified. Pluggable structures for high-rate entropy generators are available, and it is most definitely not the case that /dev/random can be driven by only a hardware souce any more. This has been designed out of the device. Hardware sources are stirred into the CSPRNG (Yarrow, Fortuna) like any other entropy source. Pluggable modules may be written by third parties for additional sources.
The harvesting structures and consequently the locking have been simplified. Entropy harvesting is done in a more general way (the documentation for this will follow). There is some GREAT entropy to be had in the UMA allocator, but it is disabled for now as messing with that is likely to annoy many people.
The venerable (but effective) Yarrow algorithm, which is no longer supported by its authors now has an alternative, Fortuna. For now, Yarrow is retained as the default algorithm, but this may be changed using a kernel option. It is intended to make Fortuna the default algorithm for 11.0. Interested parties are encouraged to read ISBN 978-0-470-47424-2 "Cryptography Engineering" By Ferguson, Schneier and Kohno for Fortuna's gory details. Heck, read it anyway.
Many thanks to Arthur Mesh who did early grunt work, and who got caught in the crossfire rather more than he deserved to.
My thanks also to folks who helped me thresh this out on whiteboards and in the odd "Hallway track", or otherwise.
My Nomex pants are on. Let the feedback commence!
Reviewed by: trasz,des(partial),imp(partial?),rwatson(partial?)
Approved by: so(des)
collision for "no" as a country code with "NO" meaning "do not load any
keymap" (which also has been the default value in etc/defaults/rc.conf
for a long time).
The result of this collision is, that "kbdcontrol -l no" will load the
Norwegian keymap, while "keymap=no" in rc.conf was interpreted as the
lower case spelling of "NO" meaning "no keyboard" (and "no.kbd" was not
loaded).
Fix this by matching only the upper-case spelling "NO" in rc.d/syscons
when deciding whether to load a keymap file.
This will lead to "no.kbd" being loaded, if the until now valid (but
non-default) spelling "no" was used in an individual rc.conf file to mean
"no keyboard". But all alternatives I could think of introduce a larger
violation of POLA ...
Reported by: Gyrd Thane Lange (gyrd-se at thanelange.no)
MFC after: 3 days
This is cleaner and eliminates the unneeded startup of KVP daemon on
systems that do not run as a Hyper-V guest.
Submitted by: hrs
X-MFC-with: 271493, 271688, 271699
run when asked for by the user. Right now, hv_kvpd is run on every boot.
Don't do that.
Add hv_kvpd_enable= for this script to be run.
MFC with 271493
MFC after: 2 weeks
Relnotes: yes
The following warnings were displayed:
sysctl: net.inet.ip.sourceroute=0: Operation not permitted
sysctl: net.inet.ip.accept_sourceroute=0: Operation not permitted
many thanks for their continued support of FreeBSD.
While I'm there, also implement a new build knob, WITHOUT_HYPERV to
disable building and installing of the HyperV utilities when necessary.
The HyperV utilities are only built for i386 and amd64 targets.
This is a stable/10 candidate for inclusion with 10.1-RELEASE.
Submitted by: Wei Hu <weh microsoft com>
MFC after: 1 week
- Identify the console driver used and print syscons or vt as appropriate.
- If vt is used and a keymap could not be loaded, then try to replace the
keymap name configured in rc.conf based on a replacement list in this
script. Warn about the fact, that a syscons keyname is configured and
report the replacement used under vt.
- If no replacement keymap is found, no keymap is loaded and a warning
is displayed, which points at the conversion script and allows the
conversion of keymaps not part of the official distribution.
This patch has been sent to the -hackers list for review, but no comment
has been received, yet. It is tested to work under syscons and vt on my
system (on vt with either the syscons or vt keymap file name in rc.conf).
MFC after: 3 days
- Rename $kerberos5_server_enable with $kdc_enable and rename
rc.d/kerberos with rc.d/kdc.
- Rename $kadmin5_server_enable with $kadmind_enable.
- Rename ${kerberos5,kpasswdd}_server with ${kdc,kpasswdd}_program.
- Fix rc.d/{kadmind,kerberos,kpasswdd,kfd} scripts not to change variables
after load_rc_config().
- Add rc.d/ipropd_master and rc.d/ipropd_slave scripts. These are
for iprop-master(8) and iprop-slave(8). Keytab used for iprop service is
defined in ipropd_{master,slave}_keytab (/etc/krb5.keytab by default).
- Add dependency on rc.d/kdc to SERVERS. rc.d/kdc must be invoked as early
as possible before scripts divided by rc.d/SERVERS.
Note that changes to rc.d/{kdc,kpasswdd,kadmind} are backward-compatible
with the old configuration variables:
${kerberos5,kpasswdd,kadmin5}_server{,_enable,_flags}.
UNIX systems, eg. MacOS X and Solaris. It uses Sun-compatible map format,
has proper kernel support, and LDAP integration.
There are still a few outstanding problems; they will be fixed shortly.
Reviewed by: allanjude@, emaste@, kib@, wblock@ (earlier versions)
Phabric: D523
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
stop timer. since watchdogd rc.d script is marked as 'shutdown'
it will exit (on shutdown) and stop timer. if system happens to
hung after watchdogd exited, manual reset is required. when one
operates in "lights-out" type of environments and without
readily available "remote hands" it could create a problem.
this provides ability to override "stop signal" for watchdogd.
default behavior is preserved, i.e. watchdogd will still be killed
via SIGTERM and timer will be stopped. in order to activate new
feature, one needs to put
watchdogd_sig_stop="KILL"
into /etc/rc.conf and also make sure watchdogd timeout is set
to long enough value allowing system to come back online before
timeout fires.
Obtained from: Netflix
MFC after: 1 week
the first alias had to be _alias0 and processing stopped at the first non-
defined variable (preventing gaps). Allowing gaps gives the administrator
the ability to group aliases in an adhoc manner and also lifts the
requirement to renumber aliases simply to comment-out an existing one.
Aliases are processed in numerical ascending order.
Discussed on: -rc
MFC after: 1 week
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
for ipv6 jails.
Among the harmful side effects included putting a route to an entire /64
onto an interface even if you were in a smaller network - eg: /80.
This broke the freebsd.org cluster hosted at ISC which has /80 networks.
The ng_create_one() and ng_mkpeer() functions in network.subr are
now not used anywhere, but I left them, since they can be useful
in future in netgraph scripting.
Submitted by: pluknet
and enable the usage by sendmail if sendmail is enabled. Include and
document knobs to disable this feature and also set the Common Name of
the certificate created.
As the certificate is signed w/ a discarded key, it only helps prevent
Eve, but not Malory from knowing the contents of the emails.
This means that new installs (and people that use the updated freebsd.mc
file) will automaticly have STARTTLS enabled allowing incoming email to
be encrypted in most cases.
Reviewed by: gshapiro
MFC after: 3 days
Security: Yes, please.
- Fix a bug that some $jail_{jname}_foo variables did not work.
- Fix a bug which prevented $jail_devfs_ruleset from working[1].
- Move $jail_parameters to the last of the configuraiton lines[1].
Reported by: Jase Thew[1]
Approved by: re (glebius)
mount.devfs but mounts fdescfs. The mount happens just after
mount.devfs.
- rc.d/jail now displays whole error message from jail(8) when a jail
fails to start.
Approved by: re (gjb)
Refactor of /dev/random device. Main points include:
* Userland seeding is no longer used. This auto-seeds at boot time
on PC/Desktop setups; this may need some tweeking and intelligence
from those folks setting up embedded boxes, but the work is believed
to be minimal.
* An entropy cache is written to /entropy (even during installation)
and the kernel uses this at next boot.
* An entropy file written to /boot/entropy can be loaded by loader(8)
* Hardware sources such as rdrand are fed into Yarrow, and are no
longer available raw.
------------------------------------------------------------------------
r256240 | des | 2013-10-09 21:14:16 +0100 (Wed, 09 Oct 2013) | 4 lines
Add a RANDOM_RWFILE option and hide the entropy cache code behind it.
Rename YARROW_RNG and FORTUNA_RNG to RANDOM_YARROW and RANDOM_FORTUNA.
Add the RANDOM_* options to LINT.
------------------------------------------------------------------------
r256239 | des | 2013-10-09 21:12:59 +0100 (Wed, 09 Oct 2013) | 2 lines
Define RANDOM_PURE_RNDTEST for rndtest(4).
------------------------------------------------------------------------
r256204 | des | 2013-10-09 18:51:38 +0100 (Wed, 09 Oct 2013) | 2 lines
staticize struct random_hardware_source
------------------------------------------------------------------------
r256203 | markm | 2013-10-09 18:50:36 +0100 (Wed, 09 Oct 2013) | 2 lines
Wrap some policy-rich code in 'if NOTYET' until we can thresh out
what it really needs to do.
------------------------------------------------------------------------
r256184 | des | 2013-10-09 10:13:12 +0100 (Wed, 09 Oct 2013) | 2 lines
Re-add /dev/urandom for compatibility purposes.
------------------------------------------------------------------------
r256182 | des | 2013-10-09 10:11:14 +0100 (Wed, 09 Oct 2013) | 3 lines
Add missing include guards and move the existing ones out of the
implementation namespace.
------------------------------------------------------------------------
r256168 | markm | 2013-10-08 23:14:07 +0100 (Tue, 08 Oct 2013) | 10 lines
Fix some just-noticed problems:
o Allow this to work with "nodevice random" by fixing where the
MALLOC pool is defined.
o Fix the explicit reseed code. This was correct as submitted, but
in the project branch doesn't need to set the "seeded" bit as this
is done correctly in the "unblock" function.
o Remove some debug ifdeffing.
o Adjust comments.
------------------------------------------------------------------------
r256159 | markm | 2013-10-08 19:48:11 +0100 (Tue, 08 Oct 2013) | 6 lines
Time to eat crow for me.
I replaced the sx_* locks that Arthur used with regular mutexes;
this turned out the be the wrong thing to do as the locks need to
be sleepable. Revert this folly.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com> (In original diff)
------------------------------------------------------------------------
r256138 | des | 2013-10-08 12:05:26 +0100 (Tue, 08 Oct 2013) | 10 lines
Add YARROW_RNG and FORTUNA_RNG to sys/conf/options.
Add a SYSINIT that forces a reseed during proc0 setup, which happens
fairly late in the boot process.
Add a RANDOM_DEBUG option which enables some debugging printf()s.
Add a new RANDOM_ATTACH entropy source which harvests entropy from the
get_cyclecount() delta across each call to a device attach method.
------------------------------------------------------------------------
r256135 | markm | 2013-10-08 07:54:52 +0100 (Tue, 08 Oct 2013) | 8 lines
Debugging. My attempt at EVENTHANDLER(multiuser) was a failure; use
EVENTHANDLER(mountroot) instead.
This means we can't count on /var being present, so something will
need to be done about harvesting /var/db/entropy/... .
Some policy now needs to be sorted out, and a pre-sync cache needs
to be written, but apart from that we are now ready to go.
Over to review.
------------------------------------------------------------------------
r256094 | markm | 2013-10-06 23:45:02 +0100 (Sun, 06 Oct 2013) | 8 lines
Snapshot.
Looking pretty good; this mostly works now. New code includes:
* Read cached entropy at startup, both from files and from loader(8)
preloaded entropy. Failures are soft, but announced. Untested.
* Use EVENTHANDLER to do above just before we go multiuser. Untested.
------------------------------------------------------------------------
r256088 | markm | 2013-10-06 14:01:42 +0100 (Sun, 06 Oct 2013) | 2 lines
Fix up the man page for random(4). This mainly removes no-longer-relevant
details about HW RNGs, reseeding explicitly and user-supplied
entropy.
------------------------------------------------------------------------
r256087 | markm | 2013-10-06 13:43:42 +0100 (Sun, 06 Oct 2013) | 6 lines
As userland writing to /dev/random is no more, remove the "better
than nothing" bootstrap mode.
Add SWI harvesting to the mix.
My box seeds Yarrow by itself in a few seconds! YMMV; more to follow.
------------------------------------------------------------------------
r256086 | markm | 2013-10-06 13:40:32 +0100 (Sun, 06 Oct 2013) | 11 lines
Debug run. This now works, except that the "live" sources haven't
been tested. With all sources turned on, this unlocks itself in
a couple of seconds! That is no my box, and there is no guarantee
that this will be the case everywhere.
* Cut debug prints.
* Use the same locks/mutexes all the way through.
* Be a tad more conservative about entropy estimates.
------------------------------------------------------------------------
r256084 | markm | 2013-10-06 13:35:29 +0100 (Sun, 06 Oct 2013) | 5 lines
Don't use the "real" assembler mnemonics; older compilers may not
understand them (like when building CURRENT on 9.x).
# Submitted by: Konstantin Belousov <kostikbel@gmail.com>
------------------------------------------------------------------------
r256081 | markm | 2013-10-06 10:55:28 +0100 (Sun, 06 Oct 2013) | 12 lines
SNAPSHOT.
Simplify the malloc pools; We only need one for this device.
Simplify the harvest queue.
Marginally improve the entropy pool hashing, making it a bit faster
in the process.
Connect up the hardware "live" source harvesting. This is simplistic
for now, and will need to be made rate-adaptive.
All of the above passes a compile test but needs to be debugged.
------------------------------------------------------------------------
r256042 | markm | 2013-10-04 07:55:06 +0100 (Fri, 04 Oct 2013) | 25 lines
Snapshot. This passes the build test, but has not yet been finished or debugged.
Contains:
* Refactor the hardware RNG CPU instruction sources to feed into
the software mixer. This is unfinished. The actual harvesting needs
to be sorted out. Modified by me (see below).
* Remove 'frac' parameter from random_harvest(). This was never
used and adds extra code for no good reason.
* Remove device write entropy harvesting. This provided a weak
attack vector, was not very good at bootstrapping the device. To
follow will be a replacement explicit reseed knob.
* Separate out all the RANDOM_PURE sources into separate harvest
entities. This adds some secuity in the case where more than one
is present.
* Review all the code and fix anything obviously messy or inconsistent.
Address som review concerns while I'm here, like rename the pseudo-rng
to 'dummy'.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com> (the first item)
------------------------------------------------------------------------
r255319 | markm | 2013-09-06 18:51:52 +0100 (Fri, 06 Sep 2013) | 4 lines
Yarrow wants entropy estimations to be conservative; the usual idea
is that if you are certain you have N bits of entropy, you declare
N/2.
------------------------------------------------------------------------
r255075 | markm | 2013-08-30 18:47:53 +0100 (Fri, 30 Aug 2013) | 4 lines
Remove short-lived idea; thread to harvest (eg) RDRAND enropy into the
usual harvest queues. It was a nifty idea, but too heavyweight.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
------------------------------------------------------------------------
r255071 | markm | 2013-08-30 12:42:57 +0100 (Fri, 30 Aug 2013) | 4 lines
Separate out the Software RNG entropy harvesting queue and thread
into its own files.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
------------------------------------------------------------------------
r254934 | markm | 2013-08-26 20:07:03 +0100 (Mon, 26 Aug 2013) | 2 lines
Remove the short-lived namei experiment.
------------------------------------------------------------------------
r254928 | markm | 2013-08-26 19:35:21 +0100 (Mon, 26 Aug 2013) | 2 lines
Snapshot; Do some running repairs on entropy harvesting. More needs
to follow.
------------------------------------------------------------------------
r254927 | markm | 2013-08-26 19:29:51 +0100 (Mon, 26 Aug 2013) | 15 lines
Snapshot of current work;
1) Clean up namespace; only use "Yarrow" where it is Yarrow-specific
or close enough to the Yarrow algorithm. For the rest use a neutral
name.
2) Tidy up headers; put private stuff in private places. More could
be done here.
3) Streamline the hashing/encryption; no need for a 256-bit counter;
128 bits will last for long enough.
There are bits of debug code lying around; these will be removed
at a later stage.
------------------------------------------------------------------------
r254784 | markm | 2013-08-24 14:54:56 +0100 (Sat, 24 Aug 2013) | 39 lines
1) example (partially humorous random_adaptor, that I call "EXAMPLE")
* It's not meant to be used in a real system, it's there to show how
the basics of how to create interfaces for random_adaptors. Perhaps
it should belong in a manual page
2) Move probe.c's functionality in to random_adaptors.c
* rename random_ident_hardware() to random_adaptor_choose()
3) Introduce a new way to choose (or select) random_adaptors via tunable
"rngs_want" It's a list of comma separated names of adaptors, ordered
by preferences. I.e.:
rngs_want="yarrow,rdrand"
Such setting would cause yarrow to be preferred to rdrand. If neither of
them are available (or registered), then system will default to
something reasonable (currently yarrow). If yarrow is not present, then
we fall back to the adaptor that's first on the list of registered
adaptors.
4) Introduce a way where RNGs can play a role of entropy source. This is
mostly useful for HW rngs.
The way I envision this is that every HW RNG will use this
functionality by default. Functionality to disable this is also present.
I have an example of how to use this in random_adaptor_example.c (see
modload event, and init function)
5) fix kern.random.adaptors from
kern.random.adaptors: yarrowpanicblock
to
kern.random.adaptors: yarrow,panic,block
6) add kern.random.active_adaptor to indicate currently selected
adaptor:
root@freebsd04:~ # sysctl kern.random.active_adaptor
kern.random.active_adaptor: yarrow
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
Submitted by: Dag-Erling Smørgrav <des@FreeBSD.org>, Arthur Mesh <arthurmesh@gmail.com>
Reviewed by: des@FreeBSD.org
Approved by: re (delphij)
Approved by: secteam (des,delphij)
command line options. The "jail_<jname>_*" rc.conf(5) variables for
per-jail configuration are automatically converted to
/var/run/jail.<jname>.conf before the jail(8) utility is invoked.
This is transparently backward compatible.
- Fix a minor bug in jail(8) which prevented it from returning false
when jail -r failed.
Approved by: re (glebius)
is ignored except for "rc.d/netif vnet{up,down} ifn" because a jail is
usually created after interface initialization on boot time.
"rc.d/netif vnetup ifn" moves ifn into the specified jail. It is
designed to be used in other scripts like rc.d/jail, not automatically
invoked during the interface initialization.
Approved by: re (kib)
