the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
npx is no more mandatory than sc. Its mandatoryness went away in
rev.1.226 of i386/machdep.c 9 months before it was made mandatory in
rev.1.24 of config/mkmakefile.c.
This change is mainly to test building of minimal kernel configurations.
npx should really be even more standard than clk. It was optional mainly
so that the usual device driver configuration info could be specified in
the usual way in config files, but this hasn't been necessary for a few
years.
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
sio_pccard_detach to use new siodetach. Add an extra arg to sioprobe
to tell driver to probe/not probe the device for IRQs.
This incorporates most of Bruce's review material. I'm at a good
checkpoint, but there will be more to come based on bde's further
reviews.
Reviewed by: bde
Move sio from isa/sio.c to dev/sio/sio.c. The next step is to break
out the front end attachments, improve support for these parts on
different busses, and maybe, if we're lucky, merging in pc98 support.
It will also be MI and live in conf/files rather than files.*.
Approved by: bde
Tested with: i386, pc98
the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
- Move the lance_probe function to if_lnc.c.
- Support C-NET(98)S again.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata) and nyan
No response from: Paul Richards
removed and a minimal number of changes to make it compile in the new
location.
# I have a fully converted on a disk that may be crashed. If it is
# crashed, I'll redo the work.
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
__FreeBSD_version 500015 can be used to detect their disappearance.
- Move the symbols for SMP_prvspace and lapic from globals.s to
locore.s.
- Remove globals.s with extreme prejudice.
To use it, some dll is needed. And currently, the dll is only for NetBSD.
So one more kernel module is needed.
For more infomation,
http://chiharu.haun.org/peace/ .
Reviewed by: bp
This code has help us comprehence ACPI spec .
Contributors of this code is as follows(except for FreeBSD commiter):
Yasuo Yokoyama,
Munehiro Matsuda,
and ALL acpi-jp@jp.freebsd.org people.
Thanks.
R.I.P.
reducues the maintenance load for the mutex code. The only MD portions
of the mutex code are in machine/mutex.h now, which include the assembly
macros for handling mutexes as well as optionally overriding the mutex
micro-operations. For example, we use optimized micro-ops on the x86
platform #ifndef I386_CPU.
- Change the behavior of the SMP_DEBUG kernel option. In the new code,
mtx_assert() only depends on INVARIANTS, allowing other kernel developers
to have working mutex assertiions without having to include all of the
mutex debugging code. The SMP_DEBUG kernel option has been renamed to
MUTEX_DEBUG and now just controls extra mutex debugging code.
- Abolish the ugly mtx_f hack. Instead, we dynamically allocate
seperate mtx_debug structures on the fly in mtx_init, except for mutexes
that are initiated very early in the boot process. These mutexes
are declared using a special MUTEX_DECLARE() macro, and use a new
flag MTX_COLD when calling mtx_init. This is still somewhat hackish,
but it is less evil than the mtx_f filler struct, and the mtx struct is
now the same size with and without mutex debugging code.
- Add some micro-micro-operation macros for doing the actual atomic
operations on the mutex mtx_lock field to make it easier for other archs
to override/optimize mutex ops if needed. These new tiny ops also clean
up the code in some places by replacing long atomic operation function
calls that spanned 2-3 lines with a short 1-line macro call.
- Don't call mi_switch() from mtx_enter_hard() when we block while trying
to obtain a sleep mutex. Calling mi_switch() would bogusly release
Giant before switching to the next process. Instead, inline most of the
code from mi_switch() in the mtx_enter_hard() function. Note that when
we finally kill Giant we can back this out and go back to calling
mi_switch().
platforms.
While here, work around a strange quirk in config(8) that I do not yet
understand. Rearrange which atapi* files have 'optional' vs. 'count'
so that you can have atapifd without atapicd. The only difference should
be that this works instead of having a link error because atapi-all.o got
left out of the kernel.
drivers (again). These drivers have not compiled for 5-6 months.
Now that the new sound code supports MIDI, the major reason we had for
reviving it is gone. It is a far better investment polishing the new
midi code than trying to keep this on life support. Come 5.0-REL, if
there are major shortcomings in the pcm sound driver then maybe we can
rethink this, but until then we should focus on pcm.
Remember, these have not been compilable since ~April-May this year.
The code for suspend/resume is derived from APM device driver.
Some people suggested the original code is somewhat buggy, but I'd
like to just move it from apm.c without any major changes for the
initial version. This code should be refined later.
To use pmtimer to adjust time at resume time, add
device pmtimer
in your kernel config file, and add
hint.pmtimer.0.at="isa"
in your device.hints
Reviewed by: -current, bde
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
config(8). This commit allows control of the creation of the
#include "foo.h" files. We now only create them explicitly when needed.
BTW; these are mostly bad because they usually imply static limits on
numbers of units for devices. eg: struct mysoftc sc[NFOO];
These static limits have Got To Go.
Symbol values are now represented using array sizes (4 arrays per symbol
so that 16-bit machines can represent 64-bit values) instead of being raw
binary values.
Reviewed by: marcel
- Move dev/aic/aic_isa.c entry from conf/files to conf/files.MACHINE
because PC-98 uses different file.
Submitted by: nyan and IMAI Takeshi <take-i@ceres.dti.ne.jp>
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
Enable the driver in sys/conf/files.i386.
In isa/isavar.h increase ISA_NPORT from 32 to 50. This is required
because this brain-damaged card maps 49 (!) port ranges. This does
not have a negative impact because this value only specifies the maximum
number of entries in a linked list and not the size of an array which
is allocated in all drivers.
The register/fifo access routines were not newbus-ified because
1) I knew that the old code worked and is simpler and more efficient
2) the if_ed driver does something similar and
3) the newbus macros collapse to inb/outb anyway.
Reviewed and tested by: hm
Approved by: jkh
conditions are met rather than having to resort to #if's in the code.
> dev/syscons/scvgarndr.c optional sc vga
> dev/syscons/scvesactl.c optional sc vga vesa
> i386/isa/vesa.c optional vga vesa
same object file (atapi-cd.o) as the ata drivers. I'd have called it
wcd.[ch], but there's already one of those in the Attic that we can't
clobber - the good names are taken.
Fix building so that it can be compiled into LINT alongside ata.
Requested by: bde
- Split terminal emulation code from the main part of the driver so
that we can have alternative terminal emulator modules if we like in
the future. (We are not quite there yet, though.)
- Put sysmouse related code in a separate file, thus, simplifying the
main part of the driver.
As some files are added to the source tree, you need to run config(8)
before you compile a new kernel next time.
You shouldn't see any functional change by this commit; this is only
internal code reorganization.
Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.
Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.
Submitted by: mdodd
Driver is not functional yet, but does compile. Tests with xe cards
indicates that it doesn't panic the machine when they are present, but
fail to probe. Interface help in the pcic/pccard layers are needed to
complete this driver.
