Submitted by Hiroyuki Aizu <eyes@navi.org>
(refer to [FreeBSD-users-jp 65061])
Tested by Hiroharu Tamaru <tamaru@myn.rcast.u-tokyo.ac.jp>
(refer to [bsd-usb:689])
an administrative limit on the size of tty/pty input buffers, this is
mostly an inconsequential change. (slti(4) will allocate an 8 kB
static buffer instead of a 1 kB buffer due to a hack in the driver.)
The increase happens to kludge around a lame limitation of syscons,
which does not allow one to paste more than TTYHOG bytes.
PR: 42031
Reviewed by: mike (mentor)
not save (restore) the global pointer (GP) in the jmpbuf in setjmp
(longjmp) because it's not needed in general. GP is considered a
scratch register at callsites and hence is always restored after a
call (when it's possible that the call resolves to a symbol in a
different loadmodule; otherwise GP does not have to be saved and
restored at all), including calls to setjmp/longjmp. There's just
one problem with this now that we use setjmp/longjmp for context
switching: A new context must have GP defined properly for the
thread's entry point. This means that we need to put GP in the
jmpbuf and consequently that we have to restore is in longjmp.
This automaticly requires us to save it as well.
When setjmp/longjmp isn't used for context switching, this can be
reverted again.
the J_SIG0 field. While here, rename J_SIG0 to J_SIGSET and
remove J_SIG1. The main reason for this change is that the
128-bit sigset_t is now aligned on a 16-byte boundary, which
allows us to use 16-byte atomic loads and stores on CPUs that
support it. The removal of J_SIG1 is done to avoid confusion:
it is never accessed and should not be. Renaming J_SIG0 to
J_SIGSET is the icing on the cake that's better done now than
later.
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
- Use gbincore() and not incore() so that we can drop the vnode interlock
as we acquire the buflock.
- Use GB_LOCK_NOWAIT when getting bufs for read ahead clusters so that we
don't block on locked bufs.
- Convert a while loop to a howmany() that will most likely be faster on
modern processors. There is another while loop divide that was left
near by because it is operating on a 64bit int and is most likely faster.
- Cleanup the cluster_read() code a little to get rid of a goto and make
the logic clearer.
Tested on: x86, alpha
Tested by: Steve Kargl <sgk@troutmask.apl.washington.edu>
Reviewd by: arch
already own. The mtx_trylock() will fail however. Enhance the comment
at the top of the try lock function to explain this.
Requested by: jlemon and his evil netisr locking
- Add a comment about special lock order rules and Giant near the top of
subr_witness.c. Specifically, this documents and explains the real lock
order relationship between Giant and sleepable locks (i.e. lockmgr locks
and sx locks). Basically, Giant can be safely acquired either before or
after sleepable locks and the case of Giant before a sleepable lock is
exempted as a special case.
- Add a new static function 'witness_list_lock()' that displays a single
line of information about a struct lock_instance. This is used to
make the output of witness messages more consistent and reduce some code
duplication.
- Fixup a few comments in witness_lock().
- Properly handle the Giant-before-sleepable-lock lock order exception in
a more general fashion and remove the no longer needed LI_SLEPT flag.
- Break up the last condition before assuming a reversal a bit to try
and make the logic less confusing in witness_lock().
- Axe WITNESS_SLEEP() now that LI_SLEPT is no longer needed and replace it
with a more general WITNESS_WARN() macro/function combination.
WITNESS_WARN() allows you to output a customized message out to the
console along with a list of held locks. It will optionally drop into
the debugger as well. You can exempt a single lock from the check by
passing it in as the second argument. You can also use flags to specify
if Giant should be exempt from the check, if all sleepable locks should
be exempt from the check, and if witness should panic if any non-exempt
locks are found.
- Make the witness_list() function static. Other areas of the kernel
should use the new WITNESS_WARN() instead.
- Declare some local variables at the top of the function instead of in a
nested block.
- Use mtx_owned() instead of masking off bits from mtx_lock manually.
- Read the value of mtx_lock into 'v' as a separate line rather than inside
an if statement for clarity. This code is hairy enough as it is.
owned. Previously the KASSERT would only trigger if we successfully
acquired a lock that we already held. However, _obtain_lock() fails to
acquire locks that we already hold, so the KASSERT was never checked in
the case it was supposed to fail.
interactivity of a kseg and assigns it a value of 0 through 100.
- Use sched_interact_score() to determine the dynamic priority.
- Define SCHED_CURR() in terms of sched_interact_score().
- Adjust the maximum slice back down to 100ms.
- Remove redundant clearing of ke_runq in sched_wakeup()
- Clean up #defines and comment them.
- Define one flag GB_LOCK_NOWAIT that tells getblk() to pass the LK_NOWAIT
flag to the initial BUF_LOCK(). This will eventually be used in cases
were we want to use a buffer only if it is not currently in use.
- Convert all consumers of the getblk() api to use this extra parameter.
Reviwed by: arch
Not objected to by: mckusick
Remove extraneous uses of vop_null, instead defering to the default op.
Rename vnode type "vfs" to the more descriptive "syncer".
Fix formatting for various filesystems that use vop_print.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
calculations. Keep this changes local to the function so the tick count
is in its natural form otherwise. Previously 1000 was added each time
a tick fired and we divided by 1000 when it was reported. This is done
to reduce rounding errors.
