unsupported form of the latter. This change has been reviewed and accepted
in the -hackers list.
Submitted by: Alexander Best
Reviewed by: David Schulz
- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
attached this way.
The AR5212 based NICs have a variety of RF frontends, so there's a linker set
which the AR5212 attach routine calls. The same framework is used for the
AR5416 and later but as there's a fixed RF frontend for each 11n NIC, it
is just directly attached.
However in the case of compiling a cut down HAL (eg _just_ AR9130 WMAC support),
the linker set ends up being empty and this causes the compile to fail.
So this is just a workaround for that - it means those users who wish an 11n
only HAL can compile the 11n chipsets and RF frontend they need, and just
"ath_ar5212" for the AR5212/AR5416 common code, and it'll just work.
Sponsored by: Hobnob, Inc.
will time out and close opened /dev/dspX.Y device(s), if
any. This is a workaround because we cannot unregister PCM
devices while the audio character device is in use.
Add a missing inclusion guard.
MFC after: 1 weeks
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
messages.
o Add check for actually resolved speed in miibus_statchg callback
instead of blindly reprogramming BCE_EMAC_MODE register. The
callback may be called multiple times(e.g. link UP, link
transition, auto-negotiate complete etc) while auto-negotiation
is in progress. All unresolved link state changes are ignored
now and setting BCE_EMAC_MODE after link establishment is done
once.
o bce(4) is careful enough not to drive MII_TICK if driver got a
valid link. To detect lost link, bce(4) relied on link state
change interrupt and if driver see the interrupt, it forced to
drive MII_TICK by calling bce_tick() in interrupt handler.
Because bce(4) generates multiple link state change interrupts
while auto-negotiation is in progress, bce_tick() would be
called multiple times and this resulted in generating multiple
link UP/DOWN messages.
With this change, bce_tick() is not called in interrupt handler
anymore such that miibus_statchg callback handles link state
changes with consistent manner.
Reviewed by: davidch
If I interpret the C standard correctly, the storage specifier should be
placed before the inline keyword. While at it, replace __inline by
inline in the files affected.
As C1X is close to being released, there is no need to wrap around a
feature that is already part of C90. Most of these files already use
`const' in different placed as well.
- in destroy_lun_state() assert hold == 1 instead of 0, as it should
receive hold taken by the create_lun_state() or get_lun_statep() before;
- fix hold count leak inside rls_lun_statep() that also fired above assert;
- in destroy_lun_state() use SIM bus number instead of SIM path id for
ISP_GET_PC_ADDR(), as it was before r196008;
- make isp_disable_lun() to set status in CCB;
- make isp_target_mark_aborted() set status into the proper CCB.
Reviewed by: mjacob
Sponsored by: iXsystems, inc.
MFC after: 1 month
- Two struct members eee_disable are used in a function that expects
an int *, so declare them int, not bool.
- igb_tx_ctx_setup() returns a boolean value, so declare it bool, not int.
- igb_header_split is passed to TUNABLE_INT, so delcare it int, not bool.
- igb_tso_setup() returns a bool, so declare it bool, not boolean_t.
- Do not re-define bool/true/false if the symbols already exist.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
- {ixgbe,ixv}_header_split is passed to TUNABLE_INT, so delcare it
int, not bool.
- {ixgbe,ixv}_tx_ctx_setup() returns a boolean value, so declare it
bool, not int.
- {ixgbe,ixv}_tso_setup() returns a bool, so declare it bool, not boolean_t.
- {ixgbe,ixv}_txeof() returns a bool, so declare it bool, not boolean_t.
- Do not re-define bool if the symbol already exists.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
processors with CPUID signature 06_1AH, 06_1EH, and 06_1FH.
Refuse to allocate them on unsupported model.
Submitted by: Davide Italiano <davide.italiano@gmail.com>
MFC after: 1 month
There have still been intermittent problems with apparent TX
hangs for some customers. These have been problematic to reproduce
but I believe these changes will address them. Testing on a number
of fronts have been positive.
EM: there is an important 'chicken bit' fix for 82574 in the shared
code this is supported in the core here.
- The TX path has been tightened up to improve performance. In
particular UDP with jumbo frames was having problems, and the
changes here have improved that.
- OACTIVE has been used more carefully on the theory that some
hangs may be due to a problem in this interaction
- Problems with the RX init code, the "lazy" allocation and
ring initialization has been found to cause problems in some
newer client systems, and as it really is not that big a win
(its not in a hot path) it seems best to remove it.
- HWTSO was broken when VLAN HWTAGGING or HWFILTER is used, I
found this was due to an error in setting up the descriptors
in em_xmit.
IGB:
- TX is also improved here. With multiqueue I realized its very
important to handle OACTIVE only under the CORE lock so there
are no races between the queues.
- Flow Control handling was broken in a couple ways, I have changed
and I hope improved that in this delta.
- UDP also had a problem in the TX path here, it was change to
improve that.
- On some hardware, with the driver static, a weird stray interrupt
seems to sometimes fire and cause a panic in the RX mbuf refresh
code. This is addressed by setting interrupts late in the init
path, and also to set all interrupts bits off at the start of that.
support of new deltas for both em and igb drivers.
Note that I am not able to track all the bugs fixed in
this code, I am a consumer of it as a component of my
core drivers. It is important to keep the FreeBSD drivers
up to date with it however.
One important note is there is a key fix for 82574 in this
update. Also, there are lots of white space changes, I am
not happy about them but have no control over it :)
control. Controller does not automatically generate pause frames
based on number of available RX buffers so it's very hard to
know when driver should generate XON frame in time. The only
mechanism driver can detect low number of RX buffer condition is
ET_INTR_RXRING0_LOW or ET_INTR_RXRING1_LOW interrupt. This
interrupt is generated whenever controller notices the number of
available RX buffers are lower than pre-programmed value(
ET_RX_RING0_MINCNT and ET_RX_RING1_MINCNT register). This scheme
does not provide a way to detect when controller sees enough number
of RX buffers again such that efficient generation of XON/XOFF
frame is not easy.
While here, add more flow control related register definition.
interrupt is ours. Note, interrupts are automatically ACKed when
the status register is read.
Add RX/TX DMA error to interrupt handler and do full controller
reset if driver happen to encounter these errors. There is no way
to recover from these DMA errors without controller reset.
Rename local variable name intrs with status to enhance
readability.
While I'm here, rename ET_INTR_TXEOF and ET_INTR_RXEOF to
ET_INTR_TXDMA and ET_INTR_RXDMA respectively. These interrupts
indicate that a frame is successfully DMAed to controller's
internal FIFO and they have nothing to do with EOF(end of frame).
Driver does not need to wait actual end of TX/RX of a frame(e.g.
no need to wait the end signal of TX which is generated when a
frame in TX FIFO is emptied by MAC). Previous names were somewhat
confusing.
suspend state. This will save more power.
On resume, make sure to enable all clocks. While I'm here, if
controller is not fast ethernet, enable gigabit PHY.
Don't blindly re-initialize controller whenever MTU is changed.
Now, reinitializing is done only when driver is running.
While here, remove unnecessary assignment of error value since it
was already initialized to 0.
o Do not report link status if driver is not running.
o TX/RX MAC configuration should be done with resolved speed,
duplex and flow control after establishing a link so it can't
be done in driver initialization routine.
Move the configuration to miibus_statchg callback which will be
called whenever any link state change is detected.
At this moment, flow-control is not enabled yet mainly because
I was not able to set correct flow control parameters to
generate TX pause frames.
o Now TX/RX MAC is enabled only when a valid link is detected.
Rearragnge hardware initialization routine a bit to leave
enabling MAC to miibus_statchg callback. In order to that,
TX/RX DMA engine is enabled in et_init_locked().
o Introduce ET_FLAG_LINK flag to track current link state.
o Introduce ET_FLAG_FASTETHER flag to mark whether controller is
fast ethernet. This flag is checked in miibus_statchg callback
to know whether PHY established a valid link.
o In et_stop(), TX/RX MAC is explicitly disabled instead of
relying on et_reset(). And move et_reset() from et_stop() to
controller initialization. Controler reset is not required here
and it would also clear critial registers(i.e station address,
RX filter configuration, WOL etc) that are required to make WOL
work.
o Switching to current media is done in et_init_locked() after
setting IFF_DRV_RUNNING flag. This should ensure reliable
auto-negotiation/manual link establishment.
o In et_start_locked(), check whether driver got a valid link
before trying to send frames.
o Remove checking a link in et_tick() as this is done by
miibus_statchg callback.
manipulation of interrupt register access is done through
CSR_WRITE_4 macro. Also add disabling interrupt into et_reset()
because we want interrupt disabled state after controller reset.
While I'm here slightly change interrupt handler to be more
readable one.
send a single TX command after setting up all TX frames. This
removes unnecessary register accesses and bus_dmamap_sync(9) calls.
et(4) uses TX interrupt moderation so it's possible to have TX
buffers that were already transmitted but waiting for TX completion
interrupt. If the number of available TX descriptor is less then
1/3 of total TX descriptor, try reclaiming first to get enough free
TX descriptors before setting up TX descriptors.
After r228325, et_txeof() no longer tries to send frames after
reclaiming TX buffers. That change was made to give more chance
to transmit frames in main interrupt handler since we can still
send frames in interrupt handler with RX interrupt. So right
before exiting interrupt hander, after enabling interrupt, try to
send more frames. This gives slightly better performance numbers.
While I'm here reduce number of spare TX descriptors from 8 to 4.
Controller does not require reserved TX descriptors, it was just to
reduce TX overhead. After r228325, driver has much lower TX
overhead so it does not make sense to reserve 8 TX descriptors.
