- Add *_locked() entry points as needed to avoid unnecessary lock thrashing.
- Use these entry points wisely.
- Only acquire the lock once when servicing an interrupt.
- Check 'suspended' on interrupt to avoid racing detach.
- Correct a mis-spelled comment.
- Don't take the lock in vr_reset() to avoid lock thrashing in attach.
- Comment this.
Reviewed by: -net (silence)
step in making this driver more attachment neutral. Others plan on
adding acpi front ends.
Still need to cleanup the MI part of the driver because it isn't as
bus independent as it could be.
- In subr_ndis.c:ndis_allocate_sharemem(), create the busdma tags
used for shared memory allocations with a lowaddr of 0x3E7FFFFF.
This forces the buffers to be mapped to physical/bus addresses within
the first 1GB of physical memory. It seems that at least one card
(Linksys Instant Wireless PCI V2.7) depends on this behavior. I
don't know if this is a hardware restriction, or if the NDIS
driver for this card is truncating the addresses itself, but using
physical/bus addresses beyong the 1GB limit causes initialization
failures.
- Create am NDIS_INITIALIZED() macro in if_ndisvar.h and use it in
if_ndis.c to test whether the device has been initialized rather
than checking for the presence of the IFF_UP flag in if_flags.
While debugging the previous problem, I noticed that bringing
up the device would always produce failures from ndis_setmulti().
It turns out that the following steps now occur during device
initialization:
- IFF_UP flag is set in if_flags
- ifp->if_ioctl() called with SIOCSIFADDR (which we don't handle)
- ifp->if_ioctl() called with SIOCADDMULTI
- ifp->if_ioctl() called with SIOCADDMULTI (again)
- ifp->if_ioctl() called with SIOCADDMULTI (yet again)
- ifp->if_ioctl() called with SIOCSIFFLAGS
Setting the receive filter and multicast filters can only be done
when the underlying NDIS driver has been initialized, which is done
by ifp->if_init(). However, we don't call ifp->if_init() until
ifp->if_ioctl() is called with SIOCSIFFLAGS and IFF_UP has been
set. It appears that now, the network stack tries to add multicast
addresses to interface's filter before those steps occur. Normally,
ndis_setmulti() would trap this condition by checking for the IFF_UP
flag, but the network code has in fact set this flag already, so
ndis_setmulti() is fooled into thinking the interface has been
initialized when it really hasn't.
It turns out this is usually harmless because the ifp->if_init()
routine (in this case ndis_init()) will set up the multicast
filter when it initializes the hardware anyway, and the underlying
routines (ndis_get_info()/ndis_set_info()) know that the driver/NIC
haven't been initialized yet, but you end up spurious error messages
on the console all the time.
Something tells me this new behavior isn't really correct. I think
the intention was to fix it so that ifp->if_init() is only called
once when we ifconfig an interface up, but the end result seems a
little bogus: the change of the IFF_UP flag should be propagated
down to the driver before calling any other ioctl() that might actually
require the hardware to be up and running.
device is open. This allows certain old and rather special dual
floppy controllers to work on both channels, as long as you only
have one open at a time.
this more accurately reflects what the underlying hardware of most
acpi machines that don't have children pci busses.
We still need a better way to get this information from acpi/hardware.
- Remove recursive locking situations. Remove the MTX_RECURSE bit.
- Take the lock for any routine which is not called from within if_vr.c
itself; this includes entry points called by newbus, ifnet, callout,
ifmedia, and polling subsystems.
- Remove spl references from the code added to miibus callbacks in rev 1.60.
- Add the INTR_MPSAFE bit.
- Tidy up some assignments; locks are not needed for taking the address
of something at a known offset, for example.
- Tested on the machine this was committed from.
Tested on: UP only, !debug.mpsafenet && debug.mpsafenet
Reviewed by: rwatson
Put some braces around the busy-wait loop in vr_rxeoc() to make the
no-op semicolon more obvious.
No functional changes.
Running on the machine I am committing from without problems.
Reviewed by: jmallett
header pointer and then casting it to the ecdt pointer. This fixes the
-O2 build. I'm unsure what changed recently to reveal this error since
this code has been unchanged for months.
following drivers: bfe(4), em(4), fxp(4), lnc(4), tun(4), de(4) rl(4),
sis(4) and xl(4)
More patches are pending on: http://peoples.freebsd.org/~mlaier/ Please take
a look and tell me if "your" driver is missing, so I can fix this.
Tested-by: many
No-objection: -current, -net
rev. 1.68, author: mycroft
Ignore a port error that happens to come in at the same time as a
connect status change. Some root hubs seem to report both.
Obtained from: NetBSD
bus interfaces. These interfaces use the FTDI chipset with different
Vendor and Product IDs.
Add two additional baud rate enumerations. The vehicle bus interfaces
use a baud rate of 2000000. Also add 3000000 as it is the other FTDI
baud divisor special case.
I've commited a slightly different patch from that provided in the PR as
I changed the matching code a bit yesterday.
Submitted by: Mike Durian <durian at shadetreesoftware.com>
PR: kern/67357
operations when the refcount doesn't protect the opens and closes. Fix
this, and don't actually let a time out happen: now ugen(4) devices do
not get freed out from under the programs with them open.
