- Correct the logic for the AIF array index pointers so that correct slot is
always looked at.
- Copy the full FIB payload size when copying AIF's, not just the first 64
bytes.
Thanks to Mirapoint, Inc, for pointing these problems out and offering a
solution.
- Add data structuress for doing 64-bit scatter/gather
- Move busdma tag creations around so that only the parent is
created in aac_pci.c.
- Retrieve the capabilities word from the firmware before setting
up command structures and tags. This allows the driver to decide
whether to do 64-bit commands, and if work-arounds are needed for
systems with >2GB of RAM.
- Only enable the SCSI passthrough if it's enabled in the capabilities
word in the firmware.
This should fix problems with the 2120S and 2200S cards in systems with more
than 2GB of RAM. Full 64-bit support is forthcoming.
MFC-After: 1 week
aac.c:
Re-arrange the interrupt handler to optimize the common case of
the adapter interrupting us because one or more commands are complete,
and do a read across the pci bus to ensure that all posted status
writes are flushed. This should close a race that could cause command
completion interrupts to be lost.
Follow the spec a bit closer when filling out command structures.
Enable the Fast Response feature to eliminate the need for the card
to DMA successfull command completions back into host memory.
Tell the controller how much physical memory we have. Without this
there was a chance that our DMA regions would collide with the
memory window used by the cache on the controller. The result would
be massive data corruption. This seemed to mainly affect systems with
>2GB of memory.
Fix a few whitespace problems.
aac_debug.c:
Add an extra diagnostic when printing out commands.
aac_disk.c:
Add extra sanity checks.
aacreg.h:
Prepare for making this 64-bit clean by reducing the use of enumeration
types in structures.
Many thanks to Justin Gibbs for helping track these down.
ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
check is complicated by the fact that the Adaptec 5400S cards claim to use
1.x firmware also. PERC2/QC 1.x firmware is not compatible with this driver
and will cause a system hang.
MFC after: 3 days
released management apps.
1. Implement poll(). This will check for queued aif's so that a
subsequent ioctl call to retrieve the next aif will not block.
2. Don't catch signals when sleeping on a fib sent from userland. This
causes a race and panic due to the pthread context switcher waking
up the tsleep at inopportune times.
3. Fix some whitespace nits.
MFC after: 3 days
1. Correctly handle commands initiated by the adapter. These commands
are defered to a kthread responsible for their processing, then are
properly returned to the controller.
2. Add/remove disk devices when notified by the card that a container was
created/deleted/offline.
3. Implement crashdump functionality.
4. Support all ioctls needed for the management CLI to work. The linux
version of this app can be found at the Dell or HP website. A native
version will be forthcoming.
MFC-after: 4.4-RELEASE
with the driver locking up under load.
- Restructure so that we use a static pool of commands/FIBs, rather than
allocating them in clusters. The cluster allocation just made things
more complicated, and allowed us to waste more memory in peak load
situations.
- Make queueing macros more like my other drivers. This adds queue stats
for free. Add some debugging to take advantage of this.
- Reimplement the periodic timeout scan. Kick the interrupt handler
and the start routine every scan as well, just to be safe. Track busy
commands properly.
- Bring resource cleanup into line with resource allocation. We should
now clean up correctly after a failed probe/unload/etc.
- Try to start new commands when old ones are completed. We weren't doing
this before, which could lead to deadlock when the controller was full.
- Don't try to build a new command if we have found a deferred command.
This could cause us to lose the deferred command.
- Use diskerr() to report I/O errors.
- Don't bail if the AdapterInfo structure is the wrong size. Some variation
seems to be normal. We need to improve our handing of 2.x firmware sets.
- Improve some comments in an attempt to try to make things clearer.
- Restructure to avoid some warnings.
