all alphas with devices behind ppb's. I'm working on a better solution now.
Note that all alphas that use per-platform interrupt mapping are broken
again (as they have been for several months)
breakage:
- call PCIB_ROUTE_INTERRUPT() regardless of how valid the intline looks.
Some alphas leave garbage in the intline and leave the intr mapping
to OS platform support routines that map slots/buses to intlines
- Down in the alpha pci code, first try platform.pci_intr_route() and
if it doesn't exist or returns garbage, just read the intline out of
config space.
tested on AS500 (garbage in intline) and UP1000 (PC-like, intline is valid)
Note that a nice little hack like the APIC_IO section of pci_cfgregread()
is not workable. This is because the calling interface for
alpha_pci_route_interrupt() requires us to figure out the bus/slot/etc
from a device_t. At pci_read_device() time, we don't have a device_t
for the bus/slot/func in question.
- Break out the /dev/pci driver into a separate file.
- Kill the COMPAT_OLDPCI support.
- Make the EISA bridge attach a bit more like the old code; explicitly
check for the existence of eisa0/isa0 and only attach if they don't
already exist. Only make one bus_generic_attach() pass over the
bridge, once both busses are attached. Note that the stupid Intel
bridge's class is entirely unpredictable.
- Add prototypes and re-layout the core PCI modules in line with
current coding standards (not a major whitespace change, just moving
the module data to the top of the file).
- Remove redundant type-2 bridge support from the core PCI code; the
PCI-CardBus code does this itself internally. Remove the now
entirely redundant header-class-specific support, as well as the
secondary and subordinate bus number fields. These are bridge
attributes now.
- Add support for PCI Extended Capabilities.
- Add support for PCI Power Management. The interface currently
allows a driver to query and set the power state of a device.
- Add helper functions to allow drivers to enable/disable busmastering
and the decoding of I/O and memory ranges.
- Use PCI_SLOTMAX and PCI_FUNCMAX rather than magic numbers in some
places.
- Make the PCI-PCI bridge code a little more paranoid about valid
I/O and memory decodes.
- Add some more PCI register definitions for the command and status
registers. Correct another bogus definition for type-1 bridges.
- Improve the formatting for devices identified by the database.
- Fix the pcib_route_interrupt method definition, as an old version
snuck in here somehow 8(
- Remove a couple of the vendor/device IDs for PCI:ISA bridges which
correctly identify themselves.
Submitted by: peter
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
command register is too aggressive. Revert to the previous behaviour, but
leave the new behaviour available as an undocumented option. It's not
clear what the Right, Right Thing is to do here, but the more conservative
approach is safer.
#ifdef away the offending code until somebody with more newbus fu than
me can figure out where to put a default function that returns 255
without touching each alpha chipset driver..
bus/slot/function numbers. The old PCI code used other markers or
something, but without it here under the new pci code it is very hard to
tell which device is which (this only affects bootverbose mode).
enable bit hasn't been set in the command register, set the bit and
honour the register. It seems that quite a few lazy BIOS writers
aren't bothering to do this, which upsets the existing code and causes
us to miss out on properly-configured devices.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
"options COMPAT_OLDPCI". This option already existed, but now also tidies
up the declarations in #include <pci/pci*.h>. It is amazing how much stuff
was using the old pre-FreeBSD 3.x names and going silently undetected.
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
platform we're running on so we know how many bits to reserve at the top
end for the 'hose' value. It turns out that there's *just* enough room
to support all possible hoses on TurboLaser.
Reviewed by: gallatin@freebsd.org, dfr@free3bsd.org
from useful drivers such as the 3D DRI drivers I will be porting for
hardware accelerated OpenGL. The hardware will still be reported during
boot using the nomatch system.
Approved by: jkh
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
attaching to the device via chip*, use the newbus nomatch method to report
the device. This leaves them unattached so that a driver can be easily
loaded to grab them later.
background ]
Rename sys/pci/pci_ioctl.h to sys/sys/pciio.h to make it easier for
userland programs to use this interface. Reformat the file, and add a
BSD-style copyright to it.
Add a new man page for pci(4). The PCIOCGETCONF, PCIOCREAD, and PCIOCWRITE
ioctls are documented, but the PCIOCATTACHED ioctl is not documented
because it is not implemented.
Change includes of <pci/pci_ioctl.h> to <sys/pciio.h> or remove them
altogether. In many cases, pci_ioctl.h was unused.
Reviewed by: steve
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
rather than an "it's mine!" so that other newbus-aware drivers can
bid for the device too. This should allow the sym driver to out-bid
the ncr driver for devices it supports without having to modify ncr.c
at all. ncr would then function as a catch-all.
pci_probe_nomatch, so it won't be in the way when loading USB as a module.
The reason for them being there in the first place is that every
motherboard comes with USB kit and this way it looks more pretty (peter).
The real solution will be to define some method of detaching a driver
after it has attached.
