There were no serious problem reports on this in spite of my concern.
To get debug output from acpi_pci_link, just enable bootverbose flag
in usual manner (boot -v).
Approved by: re
aicasm_gram.y:
Use a direct move from allzeros to emulate a
mvi of 0.
aicasm_insformat.h:
sync $Id$
aicasm_symbol.c:
Minor header change.
Approved by: re (blanket)
pci_get_ether accesor, which gets it from the CIS for cardbus cards
(and from other pci-like buses via whatever mechanism is used there).
Submitted by: sam
Approved by: re (blanket)
sometimes, so return it when requested and it does. Also a little
more infrastructure for a few other things.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
buses support querying the MAC address in a standard-for-that-bus way.
The base pci bus returns NULL for this IVAR always.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
- If a PCI device is not present, then a 32-bit read_config() is going to
return 0xffffffff not 0xffff.
- For the 82454NX chipset, the MIOC that we read the bus numbers of the
various host-PCI bridges from is at function (slot) 0x10 not 0x0.
Approved by: re (rwatson)
1. Detect the revision of the Rhine chip we're using.
2. Use the force reset command on revisions which support
it whenever the normal reset command fails.
This should solve a wide range of "my vr0 locks up with reset
failed messages" problems. (Although the root causes should
be eventually tracked down.)
Tested by: grenville armitage <garmitage@swin.edu.au>
Obtained from: Via's if_fet driver
MFC after: 3 days
Approved by: re
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
to PCI bridge can be read be evaluating the _BBN method of the host to PCI
device. Unfortunately, there appear to be some lazy/ignorant/moronic/
whatever BIOS writers that return 0 for _BBN for all host to PCI bridges in
the system. On a system with a single host to PCI bridge this is not a
problem as the child bus of that single bridge will be bus 0 anyway.
However, on systems with multiple host to PCI bridges and l/i/m/w BIOS
writers this is a major problem resulting in all but the first host to
PCI bridge failing to attach. So, this adds a workaround.
If the _BBN of a host to PCI bridge is zero and pcib0 already exists
and is not us, the we use _ADR to look up our PCI function and slot
(we currently assume we are on bus 0) and use that to call
host_pcib_get_busno() to try and extract our bus number from config
registers on the host to PCI bridge device. If that fails, then we make
an evil assumption that ACPI's _SB_ namespace lays out the host to PCI
bridges in ascending order and use our pcib unit number as our bus
number.
Approved by: re
after configure() has run. Only create the device if ofwcons is the
highest priority console. Make a dev alias with the same name as the
firmware output-device property.
trigger a breakpoint with this chip.
- Fiddle the right bits in the cn input and output routines to disable port
interrupts and enable visibility of the masked interrupt status bits.
- Register a shutdown final event handler to put the chip back in the mode
that the prom expects.
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
o Use 32-bit unsigned types for things that really are 32-bit quantities,
not bus_addr_t. These are not the same as a bus_addr_t, so don't use
that here. Harmless on i386, introduced problems on sparc64.
Submitted by: jhb
bit in the PCI command register for the device. Otherwise, device drivers
that look at this register to see which types of BARs are usable will think
that none of them are.
This allows my Adaptec 1480A cardbus card to finally work.
Reviewed by: imp
