obsoleted in 1996 by ATA-2, and crashes some modern hardware like some
revisions of the Serverworks K2 SATA controller. Even very ancient
hardware seems not to require it. In the unlikely event this causes
problems, the previous behavior can be re-enabled by defining
ATA_LEGACY_SUPPORT at the top of this file.
Reviewed by: Alexander Motin <mav@freebsd.org>
* iwnfw has now been split into individual modules so autoloading of
firmware module(s) does work again.
* Changes have been made to RUN -> AUTH transition, this should fix the
issue reported by Glen and others.
* Brandon reported issues in iwn_cmd() with large commands, those have
been fixed to.
* DEAUTH is now handled correctly.
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Have the early USB takeover enabled for i386 and amd64
by default.
This also avoids a panic on PowerPC where the resource
isn't released properly and we find a busy resource
when the USB host controller wants to allocate it...
function may not work properly if we don't. Turn off hardware cursor as
vesa_set_mode() does.
- Add VBE 3.0 specific fields in VESA mode structure and pack it. Note
the padding is 190 bytes although VBE 3.0 says 189 bytes. It must be wrong
because the size of structure becomes 255 bytes and the specification says
it must be 256 bytes in total. In fact, an example code in the spec. does
it right, though. While we are at it, fix some i386-isms.
- Remove state buffer size limitation. It is no longer necessary since
sys/compat/x86bios/x86bios.c r198251.
- Move int 0x10 vector test into vesa_bios_post() as we always do it anyway.
splitting in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
propagated into if_bce.c anyway. It is disabled by default.
Approved by: davidch
MFC after: 3 days
On error, freeze device queue, to allow periph driver to do proper recovery.
Freeze SIM queue only in some cases, when it is needed to protect SIM.
Implement better command timeout detection logic for non-queued commands.
This fixes false positives when command with short timeout waiting for the
long one. For example, when hald tastes CD during burning process.
Read and clear SERR register on interrupt.
instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Synchronize RX return ring memory in rx_eof. This is needed
as the deviced updates this memory when receives packets.
- Decouple the synchronization of BGE status block in the interrupt
service routine: perfrom PREREAD synchronization only all accesses
to this block are finished. This seems to be more natural.
Reviewed by: yongari, marius
MFC after: 2 weeks
has been yanked, this works around a cam recounting bug when
CAM_DEV_UNCONFIGURED is set late in the detach. In certain conditions the
reference to the XPT device would not be released which would cause the usb
explore thread to sleep forever on "simfree", preventing any new usb devices to
be found/ejected on the bus.
This is intended to be a quick workaround to the problem without touching CAM
so it can be merged to 8.0.
Suggested by: mav
MFC after: 3 days
by checking PCI config space when the NIC is not
transmitting. Previously, a h/w fault would not have been
detected if the NIC was down, or handling an RX only
workload.
the race where interrupt thread can complete the request for which
timeout has fired and while mpt_timeout has blocked on mpt_lock.
Do a best effort to keep 4.x ang Giant-locked configurartions
compiling still.
Reported by: ups
Reviewed by: scottl
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
