This both avoids some dependencies on xinstall.host and allows
bootstrapping on older releases to work due to lack of at least 'install -l'
support.
Sponsored by: EMC / Isilon Storage Division
Since METAMODE has been added, sys.mk loads bsd.mkopt.mk which ends load loading
bsd.own.mk which then defines SHLIBDIR before all the Makefile.inc everywhere.
This makes /lib being populated again.
Reported by: many
Off by default, build behaves normally.
WITH_META_MODE we get auto objdir creation, the ability to
start build from anywhere in the tree.
Still need to add real targets under targets/ to build packages.
Differential Revision: D2796
Reviewed by: brooks imp
MAM is Medium Auxiliary Memory and is most commonly found as flash
chips on tapes.
This includes support for reading attributes and decoding most
known attributes, but does not yet include support for writing
attributes or reporting attributes in XML format.
libsbuf/Makefile:
Add subr_prf.c for the new sbuf_hexdump() function. This
function is essentially the same function.
libsbuf/Symbol.map:
Add a new shared library minor version, and include the
sbuf_hexdump() function.
libsbuf/Version.def:
Add version 1.4 of the libsbuf library.
libutil/hexdump.3:
Document sbuf_hexdump() alongside hexdump(3), since it is
essentially the same function.
camcontrol/Makefile:
Add attrib.c.
camcontrol/attrib.c:
Implementation of READ ATTRIBUTE support for camcontrol(8).
camcontrol/camcontrol.8:
Document the new 'camcontrol attrib' subcommand.
camcontrol/camcontrol.c:
Add the new 'camcontrol attrib' subcommand.
camcontrol/camcontrol.h:
Add a function prototype for scsiattrib().
share/man/man9/sbuf.9:
Document the existence of sbuf_hexdump() and point users to
the hexdump(3) man page for more details.
sys/cam/scsi/scsi_all.c:
Add a table of known attributes, text descriptions and
handler functions.
Add a new scsi_attrib_sbuf() function along with a number
of other related functions that help decode attributes.
scsi_attrib_ascii_sbuf() decodes ASCII format attributes.
scsi_attrib_int_sbuf() decodes binary format attributes, and
will pass them off to scsi_attrib_hexdump_sbuf() if they're
bigger than 8 bytes.
scsi_attrib_vendser_sbuf() decodes the vendor and drive
serial number attribute.
scsi_attrib_volcoh_sbuf() decodes the Volume Coherency
Information attribute that LTFS writes out.
sys/cam/scsi/scsi_all.h:
Add a number of attribute-related structure definitions and
other defines.
Add function prototypes for all of the functions added in
scsi_all.c.
sys/kern/subr_prf.c:
Add a new function, sbuf_hexdump(). This is the same as
the existing hexdump(9) function, except that it puts the
result in an sbuf.
This also changes subr_prf.c so that it can be compiled in
userland for includsion in libsbuf.
We should work to change this so that the kernel hexdump
implementation is a wrapper around sbuf_hexdump() with a
statically allocated sbuf with a drain. That will require
a drain function that goes to the kernel printf() buffer
that can take a non-NUL terminated string as input.
That is because an sbuf isn't NUL-terminated until it is
finished, and we don't want to finish it while we're still
using it.
We should also work to consolidate the userland hexdump and
kernel hexdump implemenatations, which are currently
separate. This would also mean making applications that
currently link in libutil link in libsbuf.
sys/sys/sbuf.h:
Add the prototype for sbuf_hexdump(), and add another copy
of the hexdump flag values if they aren't already defined.
Ideally the flags should be defined in one place but the
implemenation makes it difficult to do properly. (See
above.)
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
Similar to libexec/, do the same with lib/. Make WARNS=6 the norm and
lower it when needed.
I'm setting WARNS?=0 for secure/. It seems secure/ includes the
Makefile.inc provided by lib/. I'm not going to touch that directory.
Most of the code there is contributed anyway.
binaries in /bin and /sbin installed in /lib. Only the versioned files
reside in /lib, the .so symlink continues to live /usr/lib so the
toolchain doesn't need to be modified.
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
