a59a131093
40 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Scott Long
|
7628acd8ee |
Up until now, the free SCB pool received only a small initial allocation,
and new SCBs were allocated on demand later if needed. This has two problems. First, allocating SCBs involves allocating contiguous memory, and if memory is exhausted then the VM will try to page out to satisfy the request, leading to recursion and deadlock. The second problem is that it can cause lock order reversals due to parts of the VM still being under Giant. Fix the problem be allocating the full pool at driver attach, when it is safe to do so. |
||
|
Scott Long
|
032b0a17dc | Basic MPSAFE locking for the AHC and AHD drivers. | ||
Ruslan Ermilov
|
f4e9888107 | Fix -Wundef. | ||
Justin T. Gibbs
|
23a6493baf |
Enhance diagnostic printfs for the chains of free lists used to
avoid SCB ID collissions to non-packetized targets. |
||
|
Justin T. Gibbs
|
cb29ab3392 |
aic79xx.c:
aic7xxx.c: Allow print_reg() to be called with a NULL column. aic79xx.c: Correct new usage of SCB_GET_TAG(). aic7xxx.c: Fix stray ahd that snuck in here. |
||
|
Justin T. Gibbs
|
3db6c642f5 |
MF5S: Explicitly initialize timedout_scb lists, use SCB_TAG for all access
to the hardware_scb->tag field, limit max lun reported to CAM to 63,
return after a panic to silence a warning.
|
||
Warner Losh
|
098ca2bda9 | Start each of the license/copyright comments with /*-, minor shuffle of lines | ||
|
Justin T. Gibbs
|
ad32f91b6b |
Revert to basing all timeout/timer values in ms rather than us. The switch
to us was to help out the Linux port, but really just invited overflow. In fact, the request sense timer was overflowing prior to this change making it much shorter than intended. aic_osm_lib.h: Be more careful about overflow in all timer/timeout primitives. |
||
|
Justin T. Gibbs
|
0d0c8be691 |
Invert the polarity of two tests in the recovery code that could cause
the driver to issue a bus reset more quickly than intended. We want to *wait* if we find another SCB that could be the cause of this timeout, not proceed to a bus reset. Noticed by: kan |
||
|
Justin T. Gibbs
|
7afc02188a |
Add an ISA attachement to the aic7xxx driver to handle 284X controllers.
The ISA probe uses an identify routine to probe all slot locations from 1 to 14 that do not conflict with other allocated resources. This required making aic7770.c part of the driver core when compiled as a module. aic7xxx.c: aic79xx.c: aic_osm_lib.c: Use aic_scb_timer_start() consistently to start the watchdog timer. This removes a few places that verbatum copied the code in aic_scb_timer_start(). During recovery processing, allow commands to still be queued to the controller. The only requirement we have is that our recovery command be queued first - something the code already guaranteed. The only other change required to make this work is to prevent timers from being started for these newly queued commands. Approved by: re |
||
|
Justin T. Gibbs
|
789902c3ae |
Correct a very rare case where command ordering could be compromised
by a transaction performing a driver handled message sequence (an scb with the MK_MESSAGE flag set). SCBs that perform host managed messaging must always be at the head of their per-target selection queue so that the firmware knows to manually assert ATN if the current negotiation agreement is packetized. In the past we guaranteed this by queuing these SCBs separarately in the execution queue. This exposes the system to potential command reordering in two cases: 1) Another SCB for the same ITL nexus is queued that does not have the MK_MESSAGE flag set. This SCB will be queued to the per-target list which can be serviced before the MK_MESSAGE scb that preceeded it. 2) If the target cannot accept all of the commands in the per-target selection queue in one selection, the remainder is queued to the tail of the selection queues so as to effect round-robin scheduling. This could allow the MK_MESSAGE scb to be sent to the target before the requeued commands. This commit changes the firmware policy to defer queuing MK_MESSAGE SCBs into the selection queues until this can be done without affecting order. This means that the target's selection queue is either empty, or the last SCB on the execution queue is also a MK_MESSAGE SCB. During any wait, the firmware halts the download of new SCBs so only a single "holding location" is required. Luckily, MK_MESSAGE SCBs are rare and typically occur only during CAM's bus probe where only one command is outstanding at a time. However, during some recovery scenarios, the reordering *could* occur. aic79xx.c: Update ahd_search_qinfifo() and helper routines to search for pending MK_MESSAGE scbs and properly restitch the execution queue if either the MK_MESSAGE SCB is being aborted, or the MK_MESSAGE SCB can be queued due to the execution queue draining due to aborts. Enable LQOBUSFREE status to assert an interrupt. This should be redundant since a BUSFREE interrupt should always occur along with an LQOBUSFREE event, but on the Rev A, this doesn't seem to be guaranteed. When a PPR request is rejected when a previously existing packetized agreement is in place, assume that the target has been reset without our knowledge and revert to async/narrow transfers. This corrects two issues: the stale ENATNO setting that was used to send the PPR is cleared so the firmware is not confused by a future packetized selection with ATN asserted but no MK_MESSAGE flag in the SCB and it speeds up recovery by aborting any pending packetized transactions that by definition are now dead. When re-queueing SCBs after a failed negotiation attempt, ensure command ordering by freezing the device queue first. Traverse the list of pending SCBs rather than the whole SCB array on the controller when pushing MK_MESSAGE flag changes out to the controller. The original code was optimized for the aic7xxx controllers where there are fewer controller slots then pending SCBs and the firmware picks SCB slots. For the U320 controller, the hope is that we have fewer pending SCBs then the 512 slots on the controller. Enhance some diagnostics. Factor out some common code. aic79xx.h: Add prototype for new ahd_done_with_status() that is used to factor out some commone code. aic79xx.reg: Add definisions for the pending MK_MESSAGE SCB. aic79xx.seq: Defer MK_MESSAGE SCB queing to the execution queue so as to preserve command ordering. Re-arrange some of the selection processing code so the above change had no performance impact on the common code path. Close a few critical section holes. When entering a non-packetized phase, manually enable busfree interrupts, since the controller hardware does not do this automatically. aic79xx_inline.h: Enhance logging for queued SCBs. aic79xx_osm.c: Add new a new DDB ahd command, ahd_dump, which invokes the ahd_dump_card_state() routine on the unit specified with the ahd_sunit DDB command. aic79xx_pci.c: Turn on the BUSFREEREV bug for the Rev B. controller. This is required to close the busfree during non-packetized phase hole. |
||
|
Justin T. Gibbs
|
22dbd4c64c |
aic79xx.c:
Allow 500us between pauses in ahd_pause_and_flushwork(). The maximum we will wait is now 500ms. In the same routine, remove any attempt to clear ENSELO. Let the firmware do it once the current selection has completed. This avoids some race conditions having to do with non-packetized completions and the auto-clearing of ENSELO on packetized completions. Also avoid attempts to clear critical sections when interrups are pending. We are going to loop again anyway, so clearing critical sections is a waste of time. It also may not be possible to clear a critical section if the source of the interrupt was a SEQINT. aic79xx_pci.c: Use the Generic 9005 mask when looking for generic 7901B parts. This allows the driver to attach to 7901B parts on motherboards using a non-Adaptec subvendor ID. aic79xx_inline.h: Test for the SCBRAM_RD_BUG against the bugs field, not the flags field in the softc. aic79xx.c: Cancel pending transactions on devices that respond with a selection timeout. This decreases the duration of timeout recovery when a device disappears. aic79xx.c: Don't bother forcing renegotiation on a selection timeout now that we use the device reset handler to abort any pending commands on the target. The device reset handler already takes us down to async narrow and forces a renegotiation. In the device reset handlers, only send a BDR sent async event if the status is not CAM_SEL_TIMEOUT. This avoids sending this event in the selection timeout case aic79xx.c: Modify the Core timeout handler to verify that another command has the potential to timeout before passing off a command timeout as due to some other command. This safety measure is added in response to a timeout recovery failure on H2B where it appears that incoming reselection status was lost during a drive pull test. In that case, the recovery handler continued to wait for the command that was active on the bus indefinetly. While the root cause of the above issue is still being determined seems a prudent safeguard. aic79xx_pci.c: Add a specific probe entry for the Dell OEM 39320(B). aic79xx.c: aic79xx.h: aic79xx.reg: aic79xx.seq: Modify the aic79xx firmware to never cross a cacheline or ADB boundary when DMA'ing completion entries to the host. In PCI mode, at least in 32/33 configurations, the SCB DMA engine may lose its place in the data-stream should the target force a retry on something other than an 8byte aligned boundary. In PCI-X mode, we do this to avoid split transactions since many chipsets seem to be unable to format proper split completions to continue the data transfer. The above change allows us to drop our completion entries from 8 bytes to 4. We were using 8 byte entries to ensure that PCI retries could only occur on an 8byte aligned boundary. Now that the sequencer guarantees this by splitting up completions, we can safely drop the size to 4 bytes (2 byte tag, one byte SG_RESID, one byte pad). Both the split-completion and PCI retry problems only show up under high tag load when interrupt coalescing is being especially effective. The switch from a 2byte completion entry to an 8 byte entry to solve the PCI problem increased the chance of incurring a split in PCI-X mode when multiple transactions were completed at once. Dropping the completion size to 4 bytes also means that we can complete more commands in a single DMA (128byte FIFO -> 32 commands instead of 16). aic79xx.c: Modify the SCSIINT handler to defer clearing sequencer critical sections to the individual interrupt handlers. This allows us to immediately disable any outgoing selections in the case of an unexpected busfree so we don't inadvertantly clear ENSELO *after* a new selection has started. Doing so may cause the sequencer to miss a successful selection. In ahd_update_pending_scbs(), only clear ENSELO if the bus is currently busy and a selection is not already in progress or the sequencer has yet to handle a pending selection. While we want to ensure that the selection for the SCB at the head of the selection queue is restarted so that any change in negotiation request can take effect, we can't clobber pending selection state without confusing the sequencer into missing a selection. |
||
|
Justin T. Gibbs
|
4164174aff |
aic79xx.c:
aic79xx.seq: Convert the COMPLETE_DMA_SCB list to an "stailq". This allows us to safely keep the SCB that is currently being DMA'ed back the host on the head of the list while processing completions off of the bus. The newly completed SCBs are appended to the tail of the queue. In the past, we just dequeued the SCB that was in flight from the list, but this could result in a lost completion should the host perform certain types of error recovery that must cancel all in-flight SCB DMA operations. Switch from using a 16bit completion entry, holding just the tag and the completion valid bit, to a 64bit completion entry that also contains a "status packet valid" indicator. This solves two problems: o The SCB DMA engine on at least Rev B. silicon does not properly deal with a PCI disconnect that occurs at a non-64bit aligned offset in the chips "source buffer". When the transfer is resumed, the DMA engine continues at the correct offset, but may wrap to the head of the buffer causing duplicate completions to be reported to the host. By using a completion buffer in host memory that is 64bit aligned and using 64bit completion entries, such disconnects should only occur at aligned addresses. This assumes that the host bridge will only disconnect on cache-line boundaries and that cache-lines are multpiles of 64bits. o By embedding the status information in the completion entry we can avoid an extra memory reference to the HSCB for commands that complete without error. Use the comparison of a "host freeze count" and a "sequencer freeze count" to allow the host to process most SCBs that complete with non-zero status without having to clear critical sections. Instead the host can just pause the sequencer, performs any necessary cleanup in the waiting for selection list, increments its freeze count on the controller, and unpauses. This is only possible because the sequencer defers completions of SCBs with bad status until after all pending selections have completed. The sequencer then avoids referencing any data structures the host may touch during completion of the SCB until the freeze counts match. aic79xx.c: Change the strategy for allocating our sentinal HSCB for the QINFIFO. In the past, this allocation was tacked onto the QOUTFIFO allocation. Now that the qoutfifo has grown to accomodate larger completion entries, the old approach will result in a 64byte allocation that costs an extra page of coherent memory. We now do this extra allocation via ahd_alloc_scbs() where the "unused space" can be used to allocate "normal" HSCBs. In our packetized busfree handler, use the ENSELO bit to differentiate between packetized and non-packetized unexpected busfree events that occur just after selection, but before the sequencer has had the oportunity to service the selection. When cleaning out the waiting for selection list, use the SCSI mode instead of the command channel mode. The SCB pointer in the command channel mode may be referenced by the SCB dma engine even while the sequencer is paused, whereas the SCSI mode SCB pointer is only accessed by the sequencer. Print the "complete on qfreeze" sequencer SCB completion list in ahd_dump_card_state(). This list holds all SCB completions that are deferred until a pending select-out qfreeze event has taken effect. aic79xx.h: Add definitions and structures to handle the new SCB completion scheme. Add a controller flag that indicates if the controller is in HostRAID mode. aic79xx.reg: Remove macros used for toggling from one data fifo mode to the other. They have not been in use for some time. Add scratch ram fields for our new qfreeze count scheme, converting the complete dma list into an "stailq", and providing for the "complete on qfreeze" SCB completion list. Some other fields were moved to retain proper field alignment (alignment >= field size in bytes). aic79xx.seq: Add code to our idle loop to: o Process deferred completions once a qfreeze event has taken full effect. o Thaw the queue once the sequencer and host qfreeze counts match. Generate 64bit completion entries passing the SCB_SGPTR field as the "good status" indicator. The first bit in this field is only set if we have a valid status packet to send to the host. Convert the COMPLETE_DMA_SCB list to an "stailq". When using "setjmp" to register an idle loop handler, do not combine the "ret" with the block move to pop the stack address in the same instruction. At least on the A, this results in a return to the setjmp caller, not to the new address at the top of the stack. Since we want the latter (we want the newly registered handler to only be invoked from the idle loop), we must use a separate ret instruction. Add a few missing critical sections. Close a race condition that can occur on Rev A. silicon. If both FIFOs happen to be allocated before the sequencer has a chance to service the FIFO that was allocated first, we must take special care to service the FIFO that is not active on the SCSI bus first. This guarantees that a FIFO will be freed to handle any snapshot requests for the FIFO that is still on the bus. Chosing the incorrect FIFO will result in deadlock. Update comments. aic79xx_inline.h Correct the offset calculation for the syncing of our qoutfifo. Update ahd_check_cmdcmpltqueues() for the larger completion entries. aic79xx_pci.c: Attach to HostRAID controllers by default. In the future I may add a sysctl to modify the behavior, but since FreeBSD does not have any HostRAID drivers, failing to attach just results in more email and bug reports for the author. MFC After: 1week |
||
|
Justin T. Gibbs
|
8d4d7b6e19 |
In ahd_run_qoutfifos, correct a !=/== logic bug
that would cause an infinite loop any time we manually flush the good status FIFO. Also make our loop delay unconditional to ensure we don't miss any FIFO allocations by the hardware. |
||
|
Justin T. Gibbs
|
b3b25f2cbf |
ahc_eisa.c:
ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset. |
||
David E. O'Brien
|
aad970f1fe |
Use __FBSDID().
Also some minor style cleanups. |
||
|
Justin T. Gibbs
|
dcc9985adf |
Fix a race condition in the flushing of commands that
have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances. |
||
|
Justin T. Gibbs
|
4294c2dc56 |
aic79xx.h:
Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state. |
||
|
Justin T. Gibbs
|
b598de8f92 |
Correct a typo in a comment.
Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller. |
||
|
Justin T. Gibbs
|
f5db59f9d6 |
Add parenthesis so that we get all of the bits all
of the contents of the CCSCBCTL register into our local varaible. The other bits are used in later tests. This avoids a potential deadlock in ahd_run_qoutfifo() if we happen to catch the DMA engine in just the right state. |
||
|
Justin T. Gibbs
|
71b2757314 |
When single stepping, only leave ENBUSFREE enabled
if it was already enabled. We don't want to set it when it shouldn't be set, we just don't want to inadvertantly turn it off. This should fix a recent report of the aic7xxx driver repeatedly complaining of "unexpected busfree while idle" in one configuration. |
||
|
Justin T. Gibbs
|
79234f55e6 |
Work around SCSI spec violation by the Quantum Atlas 10K.
This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used. |
||
|
Justin T. Gibbs
|
1d528d6792 |
aic7770.c:
aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer. |
||
|
Scott Long
|
95c9929a3b |
aic79xx.c:
Use the special LUNLEN_SINGLE_LEVEL constant for post Rev A4 hardware for single byte luns. Without this change, Rev B hardware would place the single byte of lun data in byte 0 of the lun structure when it should be in byte 1. Since there are few if any devices on the market that support multiple luns in target mode, the corrupted lun field (which was only corrupted for non-zero luns) wasn't hurting us. Approved by: re (rwatson) |
||
|
Justin T. Gibbs
|
662152ce16 |
aic79xx.c:
aic79xx_osm.h: aic7xxx_osm.h: Explicitly define functions that take no arguments with "(void)" Approved by: RE |
||
|
Justin T. Gibbs
|
333f04d935 |
Correct/Simplify ignore wide residue message handling
aic79xx.c: In ahd_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Use multibyte in/out macros instead of shifting/masking by hand. aic79xx_inline.h: In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field. aic79xx.reg: Use the SCB_TASK_ATTRIBUTE field as a bit field in the non-packetized case. We currently only define one bit, SCB_XFERLEN_ODD. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic79xx.seq: Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case. |
||
|
Justin T. Gibbs
|
a3f571b832 |
Change hadling of the Rev. A packetized lun output bug
to be more efficient by having the sequencer copy the single byte of valid lun data into the long lun field. aic79xx.c: Memset our hardware SCB to 0 so that untouched fields don't confuse diagnostic output. With the old method for handling the Rev A bug, if the long lun field was not 0, this could result in bogus lun information being sent to drives. Use the same SCB transfer size for all chip types now that the long lun is not DMA'ed to the chip. aic79xx.seq: Add code to copy lun information for Rev.A hardware. aic79xx_inline.h: Remove host update of the long_lun field on every packetized command. |
||
|
Justin T. Gibbs
|
8089f0f033 |
Fixup spelling of "coalesce" and derivatives.
Approved by: RE |
||
|
Justin T. Gibbs
|
d7cff4ab97 |
Correct spelling errors.
Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending. |
||
|
Justin T. Gibbs
|
2cd3cc377a |
aic79xx.c:
Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped. |
||
|
Justin T. Gibbs
|
acae33b029 |
aic79xx.c:
Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors. |
||
|
Justin T. Gibbs
|
256081f980 |
Fix a missed goal.period -> goal.offset change. In
this case, the bug resulted in comparing a period against an offset. |
||
|
Justin T. Gibbs
|
0794987d01 |
aic79xx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
Save and restore the NEGOADDR address when setting
new transfer settings. The sequencer performs lookups
in the negotiation table too and it expects NEGOADDR
to remain consistent across pause/unpause sessions.
Consistently use "offset" instead of "period" to determine
if we are running sync or not.
Add a SHOW_MESSAGES diagnostic for when we assert ATN
during message processing.
Print out IU, QAS, and RTI features when showing transfer options.
Limit the syncrate after all option conformance
changes have taken place in ahd_devlimited_syncrate.
Changes in options may change the final syncrate we
accept.
Keep a copy of the hs_mailbox in our softc so that
we can perform read/modify/write operations on the
hs_mailbox without having to pause the sequencer to
read the last written value. Use the ENINT_COALESS
flag in the hs_mailbox to toggle interrupt coalessing.
Add entrypoints for enabling interrupt coalessing and
setting both a timeout (how long to wait for commands
to be coalessed) and a maximum commands to coaless value.
Add a statistics timer that decides when to enable or
disable interrupt coalessing based on load.
Add a routine, ahd_reset_cmds_pending() which is used
to update the CMDS_PENDING sequencer variable whenever
error recovery compeltes SCBs without notifying the
sequencer. Since ahd_reset_cmds_pending is called
during ahd_unpause() only if we've aborted SCBs, its
call to ahd_flush_qoutfifo should not cause recursion
through ahd_run_qoutfifo(). A panic has been added to
ensure that this recursion does not occur.
In ahd_search_qinfifo, update the CMDS_PENDING sequencer
variable directly. ahd_search_qinififo can be called
in situations where using ahd_reset_cmds_pending() might
cause recursion. Since we can safely determine the
exact number to reduce CMDS_PENDING by in this scenario
without running the qoutfifo, the manual update is sufficient.
Clean up diagnostics.
Add ahd_flush_qoutfifo() which will run the qoutfifo
as well as complete any commands sitting on the
sequencer's COMPLETE_SCB lists or the good status FIFO.
Use this routine in several places that did similar
things in an add-hoc, but incomplete, fashion. A call
to this routine was also added to ahd_abort_scbs() to
close a race.
In ahd_pause_and_flushwork() only return once selections
are safely disabled. Flush all completed commands via
ahd_flush_qoutfifo().
Remove "Now packetized" diagnostic now that this
information is incorperated into the actual negotiation
messages that are displayed.
When forcing renegotiation, don't clober the current
ppr_options. Much of the driver uses this information
to determine if we are currently packetized or not.
Remove some stray spaces at column 1 in ahd_set_tags.
When complaining about getting a host message loop
request with no pending messages, print out the
SCB_CONTROL register down on the card.
Modify the ahd_sent_msg() routine to handle a search
for an outgoing identify message. Use this to detect
a msg reject on an identify message which typically
indicates that the target thought we were packetized.
Force a renegotiation in this case.
In ahd_search_qinfifo(), wait more effectively for SCB
DMA activities to cease. We also disable SCB fetch
operations since we are about to change the qinfifo
and any fetch in progress will likely be invalidated.
In ahd_qinfifo_count(), fix the qinfifo empty case.
In ahd_dump_card_state(), print out CCSCBCTL in the
correct mode.
If we are a narrow controller, don't set the current
width to unknown when forcing a future negotiation.
This just confuses the code into attempting a wide
negotiation on a narrow bus.
Add support for task management function completions.
Modify ahd_handle_devreset so that it can handle
lun resets in addition to target resets. Use
ahd_handle_devreset for lun and target reset task
management functions.
Handle the abort task TMF race case better. We now
wait until any current selections are over and then
set the TMF back to zero. This should cause the sequencer
to ignore the abort TMF completion should it occur.
Correct a bug in the illegal phase handler that
caused us to drop down to narrow when handling the
unexpected command phase case after 3rd party
reset of a packetized device.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
aic79xx.h:
Add coalessing and HS_MAILBOX fields.
Add per-softc variables for the stats "daemon".
Add a debug option for interrupt coalessing activities.
Add two new softc flags:
o AHD_UPDATE_PEND_CMDS
Run ahd_reset_cmds_pending() on the next unpause.
o AHD_RUNNING_QOUTFIFO
Used to catch recursion through ahd_run_qoutfifo().
aic79xx.reg:
Correct register addresses related to the software timer
and the DFDBCTL register.
Add constants paramaterizing the software timer.
Add scratch ram locations for storing interrupt coalessing
tunables.
Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2.
In at least the REV A, these are writable bits. We make
use of that for a swtimer workaround in the sequencer.
Since HS_MAILBOX autoclears, provide a sequencer variable
to store its contents.
Add SEQINT codes for handling task management completions.
aic79xx.seq:
Correct ignore wide residue processing check for
a wide negotiation being in effect. We must be
in the SCSI register window in order to access the
negotiation table.
Use the software timer and a commands completed count to
implement interrupt coalessing. The command complete is
deferred until either the maximum command threshold or a
the expiration of a command deferral timer. If we have
more SCBs to complete to the host (sitting in COMPLETE_SCB
lists), always try to coaless them up to our coalessing limit.
If coalessing is enabled, but we have fewer commands oustanting
than the host's min coalessing limit, complete the command
immediately.
Add code to track the number of commands outstanding.
Commands are outstanding from the time they are placed
into the execution queue until the DMA to post completion
is setup.
Add a workaround for intvec_2 interrupts on the H2A4.
In H2A4, the mode pointer is not saved for intvec2, but
is restored on iret. This can lead to the restoration
of a bogus mode ptr. Manually clear the intmask bits and
do a normal return to compensate. We use intvec_2 to
track interrupt coalessing timeouts.
Since we cannot disable the swtimer's countdown, simply
mask its interrupt once we no longer care about it firing.
In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime
we are notified of an HS_MAILBOX update via the
HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a
local copy of persistant portions of the HS_MAILBOX as
the mailbox auto-clears on any read.
Move the test for the cfg4istat interrupt up an instruction
to hopefully close a race between the next outgoing selection
and our disabling of selections.
Add a missing ret to the last instruction in load_overrun_buf.
Add notifications to the host of task management
completions as well as the completions for commands
that completed successfully before their corresponding
TMF could be sent.
Hold a critical section during select-out processing
until we have a fully identified connection. This
removes a race condition with the legacy abort handler.
Correct a few spelling errors in some comments.
aic79xx_inline.h:
Call ahd_reset_cmds_pending() in ahd_unpause if required.
Update cmdcmplt interrupt statistics in our interrupt
handler.
Allow callers to ahd_send_scb() to set the task management
function.
aic79xx_pci.c:
Disable SERR and pause the controller prior to performing
our mmapped I/O test. The U320 controllers do not support
"auto-access-pause".
aic79xx_osm.c:
Set the task management function now that
ahd_send_scb() doesn't do it for us. We
also perform a lun reset in response to BDR
requests to packetized devices.
|
||
|
Scott Long
|
1c75404899 |
Convert the use of MAXBSIZE in the dma tag to more appropriate values.
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and (NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is more strict about checking these values that other arches. |
||
|
Scott Long
|
0c5aa4c57b |
Major update to the ahd driver to fix many bugs found in the previous
version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket) |
||
|
Scott Long
|
2de8725950 |
Use better return types and a couple of casts to eliminate warnings on
alpha. This will take the file out of sync with the private version that we maintain, but alpha tinderbox has been broken for too long. Tested on: i386, sparc64, alpha |
||
|
Justin T. Gibbs
|
c59c8a72cf |
Upgrade to version 1.1 of the aic79xx U320 driver.
aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips. |
||
|
Justin T. Gibbs
|
3f293aaf2c |
Identify the AIC7901A as such instead of an AIC7902.
Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the" |
||
|
Justin T. Gibbs
|
cdd49e97b4 | Hook up the ahd driver. | ||
|
Justin T. Gibbs
|
17d2475554 |
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X
SCSI Controller chip. |