in keeping the scripts under rc.d in sync with us. So, remove
NetBSD specific stuff (which made our scripts more complicated
than necessary).
The NetBSD ident string will be left intact, both for history and
also incase we wish to pull in future versions.
in keeping the scripts under rc.d in sync with us. So, remove
NetBSD specific stuff (which made our scripts more complicated
than necessary).
The NetBSD ident string will be left intact, both for history and
also incase we wish to pull in future versions.
in keeping the scripts under rc.d in sync with us. So, begin removal
of NetBSD specific stuff (which made our scripts more complicated
than necessary), starting with the NetBSD KEYWORD.
the throttling state in response to line transitions. Future plans
include adding support for CPU frequency changes.
Add a devd.conf entry for calling this script.
The default values for this are:
performance_cx_lowest="HIGH" # Use HLT (C0) online
performance_throttle_state="HIGH" # 100% (no throttling)
economy_cx_lowest="LOW" # Use the lowest Cx state possible
economy_throttle_state="HIGH" # 100% (no throttling)
systems are mounted. An example set of entries for /etc/rc.conf:
ataraid_enable="YES"
ataraid_devices="ar0"
ataraid_ar0_set="ad2 ad3"
ataraid_ar0_type="RAID1"
Because there is no "correct" way of doing ATA raid (ie, geom vs.
atacontrol vs. vinum) that is bikeshed proof, this rcng script stays within
the bounds of atacontrol and assumes that other RAID solutions for GEOM or
vinum will end up in a different rcNG script.
Reviewed by: green
then immediately terminate the shell (during boot this
also terminates the parent rc(8) shell). This was the pre-rcNG behaviour.
Also, remove an extraneous mount /.
PR: conf/57659
Submitted by: yar (with modifications)
time during the boot process. This is needed in the case where NFS mounts
from servers reachable only via IPSEC are in /etc/fstab.
PR: conf/42497
Submitted by: Volker Stolz
Approved by: re (rwatson)
porting this stuff back.
* Test /etc/motd for writability before trying to update it. This is
especially useful when /etc/ is mounted ro, like on a diskless boot.
(Thanks to phk for the idea on this one.)
* Make the "updating" message reflect what actually happens.
thin blue air if the kenv doesn't have any info.
This improves the truth value of the comment above significantly and
reduces the bogous output on the console considerably.
- Use a more robust check to determine if we need to load ipl.ko.
- Don't try to run ipf -E if ipfilter is already enabled. Look at
the net.inet.ipf.fr_running sysctl to figure this out. This fixes
a warning message about ipfilter being already initialized.
- Only one ipf -E command is needed. We don't need an extra one for
the -6 case which would only print a warning message about ipfilter
being already initialized.
- Fix one occurence where we were running /sbin/ipf directly without
using the ${ipfilter_program} variable if set.
- In ipfilter_stop(), don't try to save the firewall state tables if
ipfilter is disabled. Similarly, don't try to disable it if it's
already disabled. This fixes some more error messages.
dhclient couldn't get killed.
If we execute 'dhclient -r', dhclient gets already
killed, so there is no need to do it twice. Only do
this if we really have to release some leases.
Reviewed by: silence on freebsd-rc@yahoogroups.com
o The following additional configuration attributes of a jail can be
controlled from rc.conf:
- mounting devfs(5)
- mounting fdescfs(5)
- mounting procfs(5)
- custom devfs(8) ruleset
If no ruleset is specified, the default jail ruleset is used.
o The output of executing /etc/rc in the jail is now redirected
to /dev/null. Instead, the hostname of the jail is echoed if
the jail(8) command exited successfully. If the output is wanted
it can probably be redirected to a file (/var/run/$jail maybe)
instead of /dev/null.
Submitted by: Scot W. Hetzel <hetzels@westbend.net>
with modifications by Jens Rehsack <rehsack@liwing.de>
and me.
devfs(8) rules in rc(8). It is most useful for applying
rules to devfs(5) mount points in /dev or inside jails.
The following line of script is sufficient to
mount a relatively useful+secure devfs(5) in a jail:
devfs_mount_jail /some/jail/dev
Some new shell routines available to scripts that source
rc.subr(5):
o devfs_link - Makes it a little easier to create symlinks
o devfs_init_rulesets - Create devfs(8) rulesets from devfs.rules
o devfs_set_ruleset - Set a ruleset to a devfs(5) mount
o devfs_apply_ruleset - Apply a ruleset to a devfs(5) mount
o devfs_domount - Mount devfs(5) and apply some ruleset
o devfs_mount_jail - Mount devfs(5) and apply a ruleset
appropriate to jails.
Additional rulesets can be specified in /etc/devfs.rules.
If the devfs_system_ruleset variable is defined in rc.conf
and it contains the name of a ruleset defined in /etc/defaults/devfs.rules
or user supplied rulesets in /etc/devfs.rules then that ruleset will
be applied to /dev at startup by the /etc/rc.d/devfs script. It can
also be applied post-startup:
/etc/rc.d/devfs start
This is a more flexible mechanism than the previous method of using
/etc/devfs.conf. However, that method is still available.
Note: since devfs(8) doesn't provide any way for creating symlinks
as part of a ruleset, anyone wishing to create symlinks in a devfs(5)
as part of the bootup sequence will still have to rely on /etc/devfs.conf.
use the atmconfig(8) utility instead of route(8) to install those routes.
For this we need a new rc.conf variable natm_static_routes that works
just like static_routes except that the referenced routes use the syntax
of atmconfig(8).
Okay'ed by: mtm
The original name was really a mistake since
/usr/local/etc/rc.d scripts can (and usually do) start
more than just daemons. Even the output in the script
uses 'local packages.' Also, the term 'local daemons' is
used by rc.d/local, which was etc/rc.local of rcOG fame.
No repo-copy because there isn't much history to save.
I will remove localdaemons shortly with all the other
files that don't belong in rc.d anymore.
Discussed with: dougb, freebsd-rc@yahoogroups.com
for the harp(4) pseudo driver and for loadable native HARP drivers
(like hfa_pci).
To use harp(4) the rc variable natm_interfaces must be set to the
list of NATM interfaces to be used for HARP. These interfaces
will be brought up with ifconfig and the harp(4) will be loaded.
To use loadable native HARP drivers atm_load must be set to
the list of drivers to load.
Reviewed by: mtm, gordon (partly)
the address, also kill the dhclient process. Instead of doing the
release in the stop command, move it to the precmd stage and allow
rc.subr(8) to automatically kill the dhclient process by leaving the
stop command undefined.
Noticed by: mbr
variable in rc.conf to have sshd from ports (or somewhere else) installed.
So, don't make the sshd_config for the base system a required file
to start the service.
PR: conf/45766
network interfaces could only be turned on and off as a group (all
static interfaces or all dhcp interfaces).
When used to start the interface a 'long form' ifconfig output is
used to show the status of the interface, but when stopping an interface
the script will simply output the name of the interface. This is simply my
personal preference. Hopefully as this functionality matures we can
stabilize on a prefered form of output for these scripts.
A stop command to the dhclient script now explicitly releases the dhcp lease.
Behaviour at system shutdown; however, is unchanged since dhclient is not,
by default, run at that time. The client will not release its lease
at shutdown.
o Ensure rc.d/network2 and rc.d/network3 are not automatically run
during boot
o Modify script headers so rcorder(8) can put the two scripts in the
correct sequence.
o Change the provider names.
o Separate routing into two parts: static routing and routing options. The
start command will run both parts, but they can be run separately using
the static and options command, respectively:
(/etc/rc.d/routing static; /etc/rc.d/routing options)
This commit has two pieces. One half is the watchdog kernel code which lives
primarily in hardclock() in sys/kern/kern_clock.c. The other half is a userland
daemon which, when run, will keep the watchdog from firing while the userland
is intact and functioning.
Approved by: jeff (mentor)
take advantage of the rc.subr(8) glue. They are renamed dhclient_program
and dhclient_flags.
o Rename them in rc.conf(5)
o Rename them in /etc/defaults/rc.conf
o Add the deprecated variables to /etc/rc.subr
o Isolate the use of the 'command' variable to the
NetBSD specific parts in /etc/rc.d/dhclient.
o Now that dhcp_flags has also been renamed it will
be applied properly by rc.subr(8) glue code.
Reported by: John Nielsen <john@jnielsen.net>
really make much difference since this script is not used during startup
and is due to be removed before RELENG_5.
Submitted by: "Simon L. Nielsen" <simon@nitro.dk>
with the rest of the options following it. This caused problems for
people using ldconfig_insecure=yes because the '-i' switch was being
positioned before the format argument.
Approved by: markm/mentor (implicit), re/rwatson
PR: 47430
script to read /etc/devfs.conf, and take appropriate actions based on
what it finds there.
The (commented out) examples in the new devfs.conf file are taken in
part from the old rc.devfs script.
sessions if the mailer is dynamically linked. This happens because
on some systems the ldconfig script is run after the vi recovery
script.
I thought I had already fixed this with revision 1.5 of rc.d/ldconfig,
but apparently not. So, in addition I'm making ldconfig a requirement
of this script.
Approved by: markm (mentor)(implicit)
PR: bin/51767
We can't remove the sourcing of /etc/rc.devfs yet in case the user
might have custom entries in it. We will have to come up with an
/etc/devfs.rules or something to make this kind of thing easier.
Approved by: markm (mentor)(implicit)
script at which a filesystem will be mounted in FreeBSD. Without this
the script was being inserted later in the boot than necessary.
Approved by: markm (mentor) (implicit)
Reviewed by: dougb
Noticed by: Andrzej ToboÅa <san@wilk.2a.pl>
it doesn't work because the start_cmd doesn't enable ipfilter if
it is currently disabled.
Approved by: markm (mentor) (implicit)
Submitted by: Michael Lyngbøl <lyngbol@bifrost.lyngbol.dk>
PR: conf/46103
o group them together so they run one right after another
o use the NetBSD supplied ipfs script instead of tacking
it on to the end of ipnat
o Load the ipl module in ipnat and ipfilter, if it's not already
loaded
o In ipmon and ipnat show a warning if neither ipfilter nor
ipnat is enabled or the ipl module is not loaded, and exit
Approved by: markm (mentor) (implicit)
Tested by: leafy <leafy@leafy.idv.tw>
This is how it has always been done (before and after rc.d) but
I somehow failed to include it when I broke up network1.
Submitted by: bmah
Approved by: markm (mentor)(implicit)
o /etc/network.subr contains common subroutines used for seting
up network interfaces
o rc.d/hostname sets the hostname if not already set
o rc.d/nisdomain sets the nis domain *after* rpcbind but
before the yp* daemons. This fixes issues with temporary
hangs when looking up informaion in nis before it's ready.
o rc.d/netif brings network interfaces (minus dhcp) up.
o rc.d/network1 has been disabled and will be retired before
RELENG_5. It will be replaced by rc.d/netif
Approved by: markm (mentor)
stop ipfw, but not enable it again.
Aesthetic changes
o Use positve logic (instead of negative)
o create a 'stop' function, rather than putting the
commands in the stop_cmd variable.
Submitted by: des
Approved by: markm (mentor) (implicit)
devd later in the boot process. This should fix all the problems
people have had with those commits. Diskless should be working again,
and those that mount /usr with nfs should be able to do that again too.
critical remote systems. This lets us run commands from devd that
aren't on the / partition. This also means we can remove some kludges
from the networking startup that I added a while ago that caused other
problems.
There's still a race in starting devd that needs to be fixed in devd
so that things present at boot will be configured by the time devd
does daemon(). That race will be fixed later.
device node exists directly to see if OLDCARD is compiled into the
kernel. This eliminates the scary warning that people using NEWCARD
are seeing when they have pccard_enable=YES in their /etc/rc.conf
files.
withough the $natd_interface having to be explicitly specified on the
command line.
Approved by: markm (mentor)
Submitted by: Aaron D. Gifford <agifford@infowest.com>
PR: conf/47024
MFC: upon re approval
named(8) daemon by providing a new rc.conf knob: named_pidfile
that defaults to the path specified in the system-installed named.conf(5).
Approved by: markm (mentor)
Reviewed by: dougb
Noticed by : Galen Sampson <galen_sampson@yahoo.com>
Dan Pelleg <daniel+bsd@pelleg.org>
PR: conf/46402
MFC: 2 weeks (with re@ approval)
Instead, load them as part of the rc.d system. This allows us to prioritize
the initidiskless script so it runs before the configuration files are loaded
and allows us to get rid of the exit 2 hack in /etc/rc. The exit 2 never
worked anyway since it did not unset the prior configuration, causing the
diskless code to not operate properly.
Do a major cleanup and revamping of the diskless code for RCNG. This will
be backported to the non-RCNG scripts as well as -stable.
With suggestions from: Mike Makonnen <mtm@identd.net>
MFC after: 7 days
background fsck. The delay defaults to sixty seconds to allow
large applications such as the X server to start before disk I/O
bandwidth is monopolized by fsck.
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
Sponsored by: DARPA & NAI Labs.
that's being replaced here. This is what /etc/rc does now.
There is no NetBSD devfs, so there is no compatibility issue.
Not objected to by: FreeBSD-rc@yahoogroups.com
Approved by: re (murray)
to specify rules definition file for ipfilter. The default is
/etc/ipf6.rules. If there is a file which is specified by
'ipv6_ipfilter_rules', IPv6 rule is installed.
Reviewed by: Ronald van der Pol <Ronald.vanderPol@rvdp.org>
MFC after: 1 week
an entry in /etc/sysctl.conf didn't exist. Fixing this exposed a minor
typo "exits" vs. "exist".
However, there doesn't appear to be any provision to run this with
the "lastload" argument, meaning that the error will never appear.
* Space -> tabs conversion.
* Removed blanks before semicolon in "if ... ; then".
* Proper indentation of misindented lines.
* Put a full stop after some comments.
* Removed whitespace at end of line.
Approved by: silence from gordon
script did. Stuff in rc.local frequently has lines like
"echo -n ' service_name'" which look ugly without a prefix and a
trailing period. Likewise for rc.shutdown.local for consistency.
a per-machine or per-cluster (with different ways of expressing what's
part of a cluster) basis. In order for this to be effective, rc.conf
has to be reread after initdiskless is finished. Implement this by
adding a hook to etc/rc which rereads rc.conf by request. This can
also be implemented by renaming initdiskless to initdiskless.sh and
sourcing rc.conf there manually, but it was decided that, that would
be uglier than a hook in etc/rc.
Developed in concert with: gordon
rcNG. The $amd_flags variable was already taken over into $rc_flags
by run_rc_command() when amd_precmd() is executed, so changing
$amd_flags there no longer effects the actual execution of amd.
Hence in amd_precmd() the $rc_flags have to be adjusted instead.
under way to move the remnants of the a.out toolchain to ports. As the
comment in src/Makefile said, this stuff is deprecated and one should not
expect this to remain beyond 4.0-REL. It has already lasted WAY beyond
that.
Notable exceptions:
gcc - I have not touched the a.out generation stuff there.
ldd/ldconfig - still have some code to interface with a.out rtld.
old as/ld/etc - I have not removed these yet, pending their move to ports.
some includes - necessary for ldd/ldconfig for now.
Tested on: i386 (extensively), alpha
xntpd_* -> ntpd_*
portmap_* -> rpcbind_*
Also change single_mountd_enable -> mountd_enable
Changing the mountd flags brings us closer to NetBSD.
All of the old variable names are shimmed so you can continue to use the
old variable name.
Finally make /etc/rc.d/mountd no longer dependent on nfs as there are
(apparently) other consumers of mountd.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
/etc filesystem isn't enough; consequently, add "-i 4096" to the newfs
command for /etc. This results in 1022 inodes, which should be enough
for the forseeable future (although I don't know why we would ever
have more than 1000 files in a default /etc).
Silence by: -current
while. This is only the script pieces, the glue for the build comes next.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
Reviewed by: silence on -current and -hackers
Prodded by: rwatson
while. This is only the script pieces, the glue for the build comes next.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
Reviewed by: silence on -current and -hackers
Prodded by: rwatson
prevent the interfaces from being initialized by /etc/rc.network6
wrongly. So, you can explicitly initialize the interfaces by
/etc/pccard_ether.
With previous rc.network6, if you specify pccardd_flags="-z",
net.inet6.ip6.accept_rtadv was wronly set to 0, then RA was not
accepted.
was apparently smoking something when I committed the last fix, because as
ume was kindly enough to set me straight on, amd *will* start with no
arguments at all, as long as there is an /etc/amd.conf file for it to
read. What it won't do is start with *just* -p.
In any case, now it's fixed.
only doing ipnat(8). Go back to using $ipfilter_active, but turn off
$ipfilter_active when loading ipl.ko has failed.
Submitted by: devet@devet.org (Arjan de Vet)
MFC after: 3 days
conf file, or command line options. I brought this up in PR 12432,
which (ironically) obrien assigned to me after I became a committer. :)
PR: conf/12432
Submitted by: Me
$ipfilter_active. $ipfilter_enable is set to "NO" if modules fail to
load, and $ipfilter_active can be "YES" when we are not using ipf(8).
MFC after: 3 days
and looks like no other Unix diskless configuration I've ever seen.
Thus allow a more traditional /etc.
Note, the use of an MFS /var should also be settable.
Otherwise installing ports(packages) is just a total PITA.
when running natd(8) out of the rc-files. It is perfectly valid for
the interface or alias address to be set in a natd(8) configuration
file, not on the command line. Also, loosen up the restrictions on
identifying an IP address argument in 'natd_interface.'
Fix the documentation, rc.conf(5), to reflect this change.
Take the bogus default for 'natd_interface' out of /etc/defaults/rc.conf.
MFC after: 3 days
values at all if they are not purposefully set. What if the
administrator messed with them in /etc/sysctl.conf? We don't want to
overwrite them.
If 'log_in_vain' is zero, do not force the issue. If it is non-zero,
set it.
This change was submitted to the freebsd-audit mailing list for review
but received no feedback. Hindsight-enabled reviews are welcome.
PR: conf/31358
Submitted: Thomas Quinot <thomas@cuivre.fr.eu.org>
Try this out in -CURRENT, MFC, and then consider dropping the
'log_in_vain' knob all together. It really is something for
sysctl.conf(5).
PR: bin/32953
Reviewed by: -bugs discussion
MFC after: 1 week
md device and file system creation occurs *after* mtree is run, and
as such an /var/tmp/* or /tmp/* entries will be under the mountpoint
(or fail) rather than appearing in the md filesystems. This prevents
the creation of vi.recover, and might affect other localizations that
rely on the mtree calls affecting these directories.
so swap the order.
Also allow rpc.lockd and rpc.statd to be turned on if nfsclient is
enabled. They are needed to provide client side locking support.
PR: conf/27811
kernel TCP timer code: rather than checking for tcp_keepalive being
set to "YES", check for "NO" and turn off keepalives if the variable
is set in that manner.
o Note: eventually, it would make sense to remove this variable from
rc.conf management, and instead rely on sysctl.conf. In fact, this
is probably true of a number of rc.conf variables whose sole aim
is to drive the setting of sysctls at boot time.
to get it all right, allowing ipnat to be enabled independantly of ipfilter
in rc.conf (among other things).
PR: multiple
Submitted by: Arjan de Vet <devet@devet.org>
Reviewed by: Giorgos Keramidas <keramida@FreeBSD.org>
continuation lines, extra whitespace, and to use the last matching
line in the file. This syncs the host.conf generation with how
the nsswitch.conf is parsed.
Only print " host.conf" instead of a multi-line message, since this
happens on every boot.
- if nsswitch.conf exists, host.conf is auto-generated for compatibility
with legacy applications and libraries.
- if host.conf exists but nsswitch.conf does not, nsswitch.conf is auto-
generated as usual.
is required into rc.network.
Person failed to use a real name so both email addresses from PR included
(Sent was different to From).
PR: 22998
Submitted by: dl@leo.org/spock@empire.trek.org
