this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
and the Z8530 drivers used the I/O address as a quick and dirty way to
determine which channel they operated on, but formalizing this by
introducing iobase is not a solution. How for example would a driver
know which channel it controls for a multi-channel UART that only has a
single I/O range?
Instead, add an explicit field, called chan, to struct uart_bas that
holds the channel within a device, or 0 otherwise. The chan field is
initialized both by the system device probing (i.e. a system console)
or it is passed down to uart_bus_probe() by any of the bus front-ends.
As such, it impacts all platforms and bus drivers and makes it a rather
large commit.
Remove the use of iobase in uart_cpu_eqres() for pc98. It is expected
that platforms have the capability to compare tag and handle pairs for
equality; as to determine whether two pairs access the same device or
not. The use of iobase for pc98 makes it impossible to formalize this
and turn it into a real newbus function later. This commit reverts
uart_cpu_eqres() for pc98 to an unimplemented function. It has to be
reimplemented using only the tag and handle fields in struct uart_bas.
Rewrite the SAB82532 and Z8530 drivers to use the chan field in struct
uart_bas. Remove the IS_CHANNEL_A and IS_CHANNEL_B macros. We don't
need to abstract anything anymore.
Discussed with: nyan
Tested on: i386, ia64, sparc64
an UART interface could get stuck when a new interrupt condition
arose while servicing a previous interrupt. Since an interrupt was
already pending, no new interrupt would be triggered.
Avoid infinite recursion by flushing the Rx FIFO and marking an
overrun condition when we could not move the data from the Rx
FIFO to the receive buffer in toto. Failure to flush the Rx FIFO
would leave the Rx ready condition pending.
Note that the SAB 82532 already did this due to the nature of the
chip.
precisely where locking would be needed before adding it, but it
seems uart(4) draws slightly too much attention to have it without
locking for too long.
The lock added is a spinlock that protects access to the underlying
hardware. As a first and obvious stab at this, each method of the
hardware interface grabs the lock. Roughly speaking this serializes
the methods. Exceptions are the probe, attach and detach methods.
We simply use the detected FIFO size to determine whether we have
a post 16550 UART or not. The support lacks proper serialization of
hardware access for now.
the "compatible" property too in the ns8250 case. This gets the serial
console to work on Blade 100s, where the device name is just "serial".
Reviewed by: marcel
Second (PPS) timing interface. The support is non-optional and by
default uses the DCD line signal as the pulse input. A compile-time
option (UART_PPS_ON_CTS) can be used to have uart(4) use the CTS line
signal.
Include <sys/timepps.h> in uart_bus.h to avoid having to add the
inclusion of that header in all source files.
Reviewed by: phk
is not a size of 1. Since we already know there is a FIFO, we can
safely assume that it is at least 16 bytes. Note that all this is
mostly academic anyway. We don't use the size of the Rx FIFO
currently. If we add support for hardware flow control, we only
care about Rx FIFO sizes larger than 16.
from the SAB82532 and the Z8530 hardware drivers by introducing
uart_cpu_busaddr(). The assumption is not true on pc98 where
bus_space_handle_t is a pointer to a structure.
The uart_cpu_busaddr() function will return the bus address
corresponding the tag and handle given to it by the BAS.
WARNING: the intend of the function is STRICTLY to allow hardware
drivers to determine which logical channel they control and is NOT
to be used for actual I/O. It is therefore EXPLICITLY allowed that
uart_cpu_busaddr() returns only the lower 8 bits of the address
and garbage in all other bits. No mistakes...
(ns8250 copied and s/ns8250/i8251/g), but there for linkage purposes.
Real code to follow, once I get past some boot issues on my pc98 boxes
with recent current.
It improves on sio(4) in the following areas:
o Fully newbusified to allow for memory mapped I/O. This is a must
for ia64 and sparc64,
o Machine dependent code to take full advantage of machine and firm-
ware specific ways to define serial consoles and/or debug ports.
o Hardware abstraction layer to allow the driver to be used with
various UARTs, such as the well-known ns8250 family of UARTs, the
Siemens sab82532 or the Zilog Z8530. This is especially important
for pc98 and sparc64 where it's common to have different UARTs,
o The notion of system devices to unkludge low-level consoles and
remote gdb ports and provides the mechanics necessary to support
the keyboard on sparc64 (which is UART based).
o The notion of a kernel interface so that a UART can be tied to
something other than the well-known TTY interface. This is needed
on sparc64 to present the user with a device and ioctl handling
suitable for a keyboard, but also allows us to cleanly hide an
UART when used as a debug port.
Following is a list of features and bugs/flaws specific to the ns8250
family of UARTs as compared to their support in sio(4):
o The uart(4) driver determines the FIFO size and automaticly takes
advantages of larger FIFOs and/or additional features. Note that
since I don't have sufficient access to 16[679]5x UARTs, hardware
flow control has not been enabled. This is almost trivial to do,
provided one can test. The downside of this is that broken UARTs
are more likely to not work correctly with uart(4). The need for
tunables or knobs may be large enough to warrant their creation.
o The uart(4) driver does not share the same bumpy history as sio(4)
and will therefore not provide the necessary hooks, tweaks, quirks
or work-arounds to deal with once common hardware. To that extend,
uart(4) supports a subset of the UARTs that sio(4) supports. The
question before us is whether the subset is sufficient for current
hardware.
o There is no support for multiport UARTs in uart(4). The decision
behind this is that uart(4) deals with one EIA RS232-C interface.
Packaging of multiple interfaces in a single chip or on a single
expansion board is beyond the scope of uart(4) and is now mostly
left for puc(4) to deal with. Lack of hardware made it impossible
to actually implement such a dependency other than is present for
the dual channel SAB82532 and Z8350 SCCs.
The current list of missing features is:
o No configuration capabilities. A set of tunables and sysctls is
being worked out. There are likely not going to be any or much
compile-time knobs. Such configuration does not fit well with
current hardware.
o No support for the PPS API. This is partly dependent on the
ability to configure uart(4) and partly dependent on having
sufficient information to implement it properly.
As usual, the manpage is present but lacks the attention the
software has gotten.
