caller to vm_page_grab(). Although this gives VM_ALLOC_ZERO a
different meaning for vm_page_grab() than for vm_page_alloc(), I feel
such change is necessary to accomplish other goals. Specifically, I
want to make the PG_ZERO flag immutable between the time it is
allocated by vm_page_alloc() and freed by vm_page_free() or
vm_page_free_zero() to avoid locking overheads. Once we gave up on
the ability to automatically recognize a zeroed page upon entry to
vm_page_free(), the ability to mutate the PG_ZERO flag became useless.
Instead, I would like to say that "Once a page becomes valid, its
PG_ZERO flag must be ignored."
same problems as their Hurricane 575* bretheren in that one could set
the memory mapped port, but that has no effect. Add a quirk for this.
# I'll have to see if I can dig up documentation on these parts to see
# if there's someway software can know this other than a table...
status registers for error conditions and updating statistics
when there are cycles left (inspired by the nge(4) driver).
- Removed the TX list counter and the producer/consumer gap; it's
enough to just ensure we don't reuse the last (free) descriptor,
as the chip may not have read its next pointer yet. If we reuse
it, the TX may stall under a heavy TX load with polling enabled.
- Dropped code to recharge the watchdog timer, it's pointless; the
watchdog routine will re-init the chip and both RX and TX lists.
without the (defunct) isa compatibility shims. The new-bus-specific
parts are very similar to the ones for the pci probe and attach.
This was held up too long waiting for a repo copy to src/sys/dev/cy,
so I decided to fix the files in their old place. This gives easier
to read and merge diffs anyway.
The "count" line in src/sys/conf/files won't be changed until after
the repo copy, so old kernel configs that specify a count need not be
(and must not be) changed until then. The count is just ignored in
the driver. One unfinished detail is dynamic allocation of arrays
with <count> and (<count> * 32) entries, and iteration over the arrays.
This is now kludged with a fixed count of 10 (up to 10 cards with up
to 32 ports each).
Prodded by: imp
Submitted by: mostly by imp
Approved by: imp
Add in missing case for i845G in the attach routine. I'll MFC this
with the rest of the change after the 4.10 codefreeze lifts.
Reviewed By: Doug Rabson
Under polling(4), we counted non-existent output packets and wasted
CPU cycles, corrected. (PR kern/64975.)
The fix in revision 1.71 to correct resetting of the watchdog timer
was wrong.
In rl(4), the TX list does not have a gap between the consumer and
producer, so the "empty TX list" test was wrong, corrected.
Also, resetting the timer to five each time we know there is still
some TX work to do was a bad idea -- under polling(4), if the chip
goes out to lunch, this results in the watchdog routine to _never_
be called. Instead, let the timer downgrade to zero and fire the
watchdog, then reset it to five when it is zero AND there is some
TX work left. (Most other network drivers need this fix too.)
MFC after: 3 days
Moved the RX ring resyncing code to ste_rxeoc(), and only run it
if we were asked to POLL_AND_CHECK_STATUS, under DEVICE_POLLING.
(This significantly reduces the CPU load.)
Improved the RX ring resyncing code by re-checking if the head
is still empty before doing resyncing. This mostly affects the
DEVICE_POLLING mode, where we run this code periodically. We
could start checking with an empty head (well, an empty ring
even), and after doing a few iterations, the chip might write
a few entries, including the head, and we would bogusly consider
this case as requiring resyncing. On a test box, this reduced
the number of resyncs done by a factor of 10.
In ste_txeof(sc), only reset the watchdog timer to zero when
the TX list is completely empty.
Converted ste_tx_prev_idx to a pointer -- faster.
Removed some bitrot.
the driver's RX ring head may fall behind the chip, causing the
stuck traffic, disordered packets, etc. Work around this by
adopting the technique of resyncing RX head used in dc(4) and
xl(4) drivers, but do it in a slightly different place to reduce
the number of resyncs needed.
Also, set the NIC's RX polling period to a more meaningful value,
to stop overloading the PCI bus (this also reduces the number of
resyncs by a factor of 3 or more in a long run; the actual number
is very dependent on a nature of the traffic).
Maintain the statistics counter as the hw.ste_rxsyncs sysctl.
In cooperation with: Vsevolod Lobko
OK'ed by: ambrisko
MFC after: 5 days
they all do and handle that without alarming the user. Also pull in a bit
of defensive code from OpenBSD that triggers when a card is recognised but
not properly classified as either Genesis or Yukon. Not that I could ever
have needed this. :-)
Obtained from: OpenBSD/NetBSD (partially)
MFC after: 2 weeks
No functional change, the previous ste_encap() was correct WRT
long mbuf chains; this just reduces code duplication.
MFC after: 3 days
Prodded by: ambrisko
attach/detach time.
Assigning the default behaviour to this particular device is
incorrect, corrupting the video BIOS aperture, and breaking
VESA support in the kernel and XFree86.
Reviewed By: dfr
MFC after: 1 week
PR: kern/62906
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
MAC address in the EEPROM, and we need to get it from OpenFirmware.
This isn't very pretty but time is lacking to do this in a better
way this near 5.2-RELEASE. This is a RELENG_5_2 candidate.
Original version by: Marius Strobl <marius@alchemy.franken.de>
Tested by: Pete Bentley <pete@sorted.org>
Reviewed by: jake
frame, not the first. It is probably also not safe to free the mbuf chain
as soon as the OWN bit is cleared on the first descriptor since the chip
may not be done copying the frame into the transmit FIFO. Revert the part of
of busdma conversion (if_dc.c rev 1.115) which changed dc_txeof() to look for
the status in the first descriptor and free the mbuf chain when processing
the first descriptor for the frame, and revert the matching changes elsewhere
in the driver. This part of the busdma change caused the driver to report
spurious collisions and output errors, even when running in full-duplex mode.
Reverting the mbuf chain handling slightly complicates dc_dma_map_txbuf(),
since it is responsible for setting the OWN bits on the descriptors, but does
not normally have direct access to the mbuf chain.
Tested by:
Dejan Lesjak <dejan.lesjak at ijs.si> alpha/<Intel 21143 10/100BaseTX>
"Xin LI" <delphij at frontfree.net> i386/<Macronix 98713 10/100BaseTX>
Wiktor Niesiobedzki <bsd at w.evip.pl> i386/<3Com OfficeConnect 10/100B>
Reviewed by: mux
report a hardware rev of 0x00000000. Sadly, the 8169 gigE MAC
also reports 0x00000000, so testing against this for exclusion
results in both cards being skipped by rl_probe(). Make the 8169
test more specific by matching against both the hwrev and the PCI
ID for this chip.
PR: kern/60824
this driver by introducing a flag saying we already stopped the device.
On my Soekris net4801, this took a ping -i 0.001 from spending 80% of
time in interrupt handling to 10% (approx numbers).
This was a particular problem for the net4801 because the tree
interfaces share the same interrupt, but it would be a problem for
any configuration where an unused if_sis interface shares an interrupt
with a busy device.
Other drivers may have similar problems.
Thanks to: Luigi
Only do short-cable on revisions that need it.
Move generic initialization before short-cable fix, in order to not
clobber short cable fix register setting.
code. Both the driver and the new code were wrong. Driver interrupt
handlers are supposed to take "void *vsc" arg, but some including all
COMPAT_ISA drivers and the pci part of the cy driver want an "int unit"
arg. They got this using bogus casts of function pointers which should
have kept working despite their bogusness. However, the new interrupt
code doesn't honor requests to pass an arg of ((void *)0), so things
are very broken if the arg is actually a representation of unit 0.
The fix is to use a normal "void *vsc" arg for the pci case and a
wrapper for the COMPAT_ISA case (of the cy driver). This cleans up
new-busification of the pci case but takes the COMPAT_ISA case a little
further from new-bus. The corresponding bug for the COMPAT_ISA case
has already been fixed similarly using a wrapper in compat_isa.c and
we need another wrapper just to undo that.
Fixed some directly related style bugs (mainly by removing compatibility
cruft).
cy.c:
Fixed an indirectly related old bug in cyattach_common(). A wrong status
was returned in the unlikely event that malloc() failed.
Approved by: re (scottl)
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
