L2 information. For an indirect route the cached L2 entry contains the
MAC address of the gateway. Typically the default route is used to
transmit multicast packets when explicit multicast routes are not
available. The ether_output() function bypasses L2 resolution function
if it verifies the L2 cache is valid, because the cached L2 address
(a unicast MAC address) is copied into the packets as the destination
MAC address. This validation, however, does not apply to broadcast and
multicast packets because the destination MAC address is mapped
according to a standard method instead.
Submitted by: Xin Li
Reviewed by: bz
Approved by: re
- Allow loopback route to be installed for address assigned to
interface of IFF_POINTOPOINT type.
- Install loopback route for an IPv4 interface addreess when the
"useloopback" sysctl variable is enabled. Similarly, install
loopback route for an IPv6 interface address when the sysctl variable
"nd6_useloopback" is enabled. Deleting loopback routes for interface
addresses is unconditional in case these sysctl variables were
disabled after an interface address has been assigned.
Reviewed by: bz
Approved by: re
things a bit:
- use dpcpu data to track the ifps with packets queued up,
- per-cpu locking and driver flags
- along with .nh_drainedcpu and NETISR_POLICY_CPU.
- Put the mbufs in flight reference count, preventing interfaces
from going away, under INVARIANTS as this is a general problem
of the stack and should be solved in if.c/netisr but still good
to verify the internal queuing logic.
- Permit changing the MTU to virtually everythinkg like we do for loopback.
Hook epair(4) up to the build.
Approved by: re (kib)
(ifconfig ifN (-)vnet <jname|jid>) work correctly.
Move vi_if_move to if.c and split it up into two functions(*),
one for each ioctl.
In the reclaim case, correctly set the vnet before calling if_vmove.
Instead of silently allowing a move of an interface from the current
vnet to the current vnet, return an error. (*)
There is some duplicate interface name checking before actually moving
the interface between network stacks without locking and thus race
prone. Ideally if_vmove will correctly and automagically handle these
in the future.
Suggested by: rwatson (*)
Approved by: re (kib)
network stacks, VNET_SYSINIT:
- Add VNET_SYSINIT and VNET_SYSUNINIT macros to declare events that will
occur each time a network stack is instantiated and destroyed. In the
!VIMAGE case, these are simply mapped into regular SYSINIT/SYSUNINIT.
For the VIMAGE case, we instead use SYSINIT's to track their order and
properties on registration, using them for each vnet when created/
destroyed, or immediately on module load for already-started vnets.
- Remove vnet_modinfo mechanism that existed to serve this purpose
previously, as well as its dependency scheme: we now just use the
SYSINIT ordering scheme.
- Implement VNET_DOMAIN_SET() to allow protocol domains to declare that
they want init functions to be called for each virtual network stack
rather than just once at boot, compiling down to DOMAIN_SET() in the
non-VIMAGE case.
- Walk all virtualized kernel subsystems and make use of these instead
of modinfo or DOMAIN_SET() for init/uninit events. In some cases,
convert modular components from using modevent to using sysinit (where
appropriate). In some cases, do minor rejuggling of SYSINIT ordering
to make room for or better manage events.
Portions submitted by: jhb (VNET_SYSINIT), bz (cleanup)
Discussed with: jhb, bz, julian, zec
Reviewed by: bz
Approved by: re (VIMAGE blanket)
non-vrtiualized sysctls so we cannot used one common function.
Add a macro to convert the arg1 in the virtualized case to
vnet.h to not expose the maths to all over the code.
Add a wrapper for the single virtualized call, properly handling
arg1 and call the default implementation from there.
Convert the two over places to use the new macro.
Reviewed by: rwatson
Approved by: re (kib)
nor destructors, as there's no actual work to do.
In most cases, the constructors weren't needed because of the existing
protocol initialization functions run by net_init_domain() as part of
VNET_MOD_NET, or they were eliminated when support for static
initialization of virtualized globals was added.
Garbage collect dependency references to modules without constructors or
destructors, notably VNET_MOD_INET and VNET_MOD_INET6.
Reviewed by: bz
Approved by: re (vimage blanket)
unused custom mutex/condvar-based sleep locks with two locks: an
rwlock (for non-sleeping use) and sxlock (for sleeping use). Either
acquired for read is sufficient to stabilize the vnet list, but both
must be acquired for write to modify the list.
Replace previous no-op read locking macros, used in various places
in the stack, with actual locking to prevent race conditions. Callers
must declare when they may perform unbounded sleeps or not when
selecting how to lock.
Refactor vnet sysinits so that the vnet list and locks are initialized
before kernel modules are linked, as the kernel linker will use them
for modules loaded by the boot loader.
Update various consumers of these KPIs based on whether they may sleep
or not.
Reviewed by: bz
Approved by: re (kib)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
little purpose and are unused in the base system.
The IOCTL functionality is entirely duplicated and routing sockets
provide a richer interface than the kqueue functionality.
Further, it is not practical for these devices to be made sensible in
the face of VIMAGE.
Bump __FreeBSD_version on the off chance that there is any code out
there that actually uses this stuff.
Reviewed by: rwatson
Discussed with: bz, zec
Approved by: re@ (kensmith)
MAXCPU to mp_maxid, and handling and reporting of requests to use more
threads than we have CPUs to run them on.
Reviewed by: bz
Approved by: re (kib)
MFC after: 6 weeks
if_addr_rlock() and if_addr_runlock() for regular address lists, and
if_maddr_rlock() and if_maddr_runlock() for multicast address lists.
We will use these in various kernel modules to avoid encoding specific
type and locking strategy information into modules that currently use
IF_ADDR_LOCK() and IF_ADDR_UNLOCK() directly.
MFC after: 6 weeks
arrays to [MAXCPU], offering moderate memory savings. In some places,
this requires using CPU_ABSENT() to handle less common platforms with
sparse CPU IDs. In several places, assert that the selected CPUID for
work placement or statistics is not CPU_ABSENT() to be on the safe side.
Discussed with: bz, jeff
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
in_ifaddrhead and INADDR_HASH address lists.
Previously, these lists were used unsynchronized as they were effectively
never changed in steady state, but we've seen increasing reports of
writer-writer races on very busy VPN servers as core count has gone up
(and similar configurations where address lists change frequently and
concurrently).
For the time being, use rwlocks rather than rmlocks in order to take
advantage of their better lock debugging support. As a result, we don't
enable ip_input()'s read-locking of INADDR_HASH until an rmlock conversion
is complete and a performance analysis has been done. This means that one
class of reader-writer races still exists.
MFC after: 6 weeks
Reviewed by: bz
Import if_epair(4), a virtual cross-over Ethernet-like interface pair.
Note these files are 1:1 from p4 and not yet connected to the build
not knowing about the new netisr interface.
Sponsored by: The FreeBSD Foundation
- at_ifawithnet(), which acquires an locks it needs and returns an
at_ifaddr reference.
- at_ifawithnet_locked(), which relies on the caller locking
at_ifaddr_list, and returns a pointer rather than a reference.
Update various consumers to prefer one or the other, including ether
and fddi output, to properly release at_ifaddr references.
Rework at_control() to manage locking and references in a manner
identical to in_control().
MFC after: 6 weeks
rather than pointers, requiring callers to properly dispose of those
references. The following routines now return references:
ifaddr_byindex
ifa_ifwithaddr
ifa_ifwithbroadaddr
ifa_ifwithdstaddr
ifa_ifwithnet
ifaof_ifpforaddr
ifa_ifwithroute
ifa_ifwithroute_fib
rt_getifa
rt_getifa_fib
IFP_TO_IA
ip_rtaddr
in6_ifawithifp
in6ifa_ifpforlinklocal
in6ifa_ifpwithaddr
in6_ifadd
carp_iamatch6
ip6_getdstifaddr
Remove unused macro which didn't have required referencing:
IFP_TO_IA6
This closes many small races in which changes to interface
or address lists while an ifaddr was in use could lead to use of freed
memory (etc). In a few cases, add missing if_addr_list locking
required to safely acquire references.
Because of a lack of deep copying support, we accept a race in which
an in6_ifaddr pointed to by mbuf tags and extracted with
ip6_getdstifaddr() doesn't hold a reference while in transmit. Once
we have mbuf tag deep copy support, this can be fixed.
Reviewed by: bz
Obtained from: Apple, Inc. (portions)
MFC after: 6 weeks (portions)
This change should make options VIMAGE kernel builds usable again,
to some extent at least.
Note that the size of struct vnet_inet has changed, though in
accordance with one-bump-per-day policy we didn't update the
__FreeBSD_version number, given that it has already been touched
by r194640 a few hours ago.
Reviewed by: bz
Approved by: julian (mentor)
- shrink size guards for vnet_net.
vnet_rtable does not need size guards as it is self-contained.
- remove a bunch of defines from vnet.h no longer valid.
Vimage module, which had been there already but now is stateful.
All variables are now file local; so this further limits the global
spreading of routing related things throughout the kernel.
Add a missing function local variable in case of MPATHing.
Reviewed by: zec
No longer export rt_tables as all lookups go through
rt_tables_get_rnh().
We cannot make rt_tables (and rtstat, rttrash[1]) static as
netstat -r (-rs[1]) would stop working on a stripped
VIMAGE_GLOBALS kernel.
Reviewed by: zec
Presumably broken by: phk 13.5y ago in r12820 [1]
a pointer to an ifaddr matching the passed socket address, returns a
boolean indicating whether one was present. In the (near) future,
ifa_ifwithaddr() will return a referenced ifaddr rather than a raw
ifaddr pointer, and the new wrapper will allow callers that care only
about the boolean condition to avoid having to free that reference.
MFC after: 3 weeks
- Unify reference count and lock initialization in a single function,
ifa_init().
- Move tear-down from a macro (IFAFREE) to a function ifa_free().
- Move reference count bump from a macro (IFAREF) to a function ifa_ref().
- Instead of using a u_int protected by a mutex to refcount(9) for
reference count management.
The ifa_mtx is now used for exactly one ioctl, and possibly should be
removed.
MFC after: 3 weeks
Add necessary changes to the kernel for this (basically introduce a
bpf_zero_counters() function). As well, update the man page.
MFC after: 1 month
Discussed with: rwatson
missing it.
Remove the "hidden" kernel only include of vimage.h from ip_var.h added
with the very first Vimage commit r181803 to avoid further kernel poisoning.
