"stray irq 9" messages on my Thinkpad. It may also help with general
reboot consistency although the recent hang on reboot was solved by
acpi_cpu.c rev 1.39.
after. Unify the paths for all Cx states. Remove cpu_idle_busy and
instead do the little profiling we need before re-enabling interrupts.
Use 1 quantum as estimate for C1 sleep duration since the timer interrupt
is the main reason we wake.
While here, change the cx_history sysctl to cx_usage and report statistics
for which idle states were used in terms of percent. This seems more
intuitive than counters. Remove the cx_stats structure since it's no
longer used. Update the man page.
Change various types which do not need explicit size.
correct. Instead, check it against the possible settings (_PRS) when
the link is probed. This is important when using APIC mode but link
devices still have PIC mode settings. This is also what Linux does.
Additional prodding by: Len Brown len dot brown at intel dot com
based on the destination sleep state. Add a method to restore the old
state on resume. This is needed for the case of suspending to a very low
state disabling a GPE (i.e. S4), resuming, and then suspending to a higher
state (i.e. S3). This case should now keep the proper GPEs enabled.
device can wake the system. For example:
dev.root0.nexus0.acpi0.acpi_lid0.wake: 1
dev.root0.nexus0.acpi0.acpi_button0.wake: 1
dev.root0.nexus0.acpi0.pcib0.wake: 0
dev.root0.nexus0.acpi0.sio0.wake: 0
acpi_wake_init:
Evaluate _PRW and set the GPE type
acpi_wake_set_enable:
Enable or disable a device's GPE.
acpi_wake_sleep_prep:
Perform any last-minute changes to the device to prepare it for
entering the given sleep state.
Also, walk the entire namespace when transitioning to a sleep state,
disabling any GPEs which aren't appropriate for the given state. Transition
acpi_lid and acpi_button to the new API.
This clears the way for non-ACPI-aware devices to wake the system (i.e.
modems) and fixes a problem where systems power up after shutdown when a
GPE is triggered.
* Add calls to AcpiSetGpeType. We use wake/run as the type for lid and
button switches since wake-only causes Thinkpads to immediately wake on
the second suspend. Note that with wake/run, some systems return both
wake and device-specific notifies so we don't register for system notifies
for lid and button switches.
* Remove the hw.acpi.osi_method tunable since it is not needed.
* Always print unknown notifies for all types.
* Add more cleanup for the EC if it fails to attach.
* Use the GPE handle now that we parse it. This allows GPEs to be defined
in AML GPE blocks.
* Always use ACPI_NOT_ISR since it's ok to acquire a mutex in our thread
which processes queued requests.
return value for BUS_READ_IVAR and thus don't generate the proper NULL
in cases where a device (i.e. on PCI) does not have a handle.
Found by: peadar, tjr
the swizzle method for routing PCI interrupts across the bridge. This
fixes problems with motherboards (typically laptops) whose BIOS doesn't
provide a PRT for the AGP bridge even though there is a device entry for
the bridge in the ACPI namespace.
Tested by: Kenneth Culver culverk at sweetdreamsracing dot biz
devices it cannot attach to. This gets rid of extraneous but harmless
device_probe_and_attach() errors. While I'm here, make the device
description more useful. The !acpi case for cpu is handled by legacy0.
individual asm versions. The global lock is shared between the BIOS and
OS and thus cannot use our mutexes. It is defined in section 5.2.9.1 of
the ACPI specification.
Reviewed by: marcel, bde, jhb
1) In pci.c, we need to check the child device's state, not the parent
device's state.
2) In acpi_pci.c, we have to run the power state change after the acpi
method when the old_state is > new state, not the other way around.
Submitted by: Dmitry Remesov
PR: 65694
added an arbitrary delay to our readings, causing us to use the ACPI-safe
read method when not necessary. Submitted by: bde
Old:
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
New:
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
Also, reduce unnecesary overhead in ACPI-fast by remove the barrier for
reads. The timer in the ACPI-fast case is known to increase monotonically
so there is no need to serialize access to it.
gadgets (hotkeys, lcd, ...) on Asus laptops. I aim to closely track the
acpi4asus project which implements these features in the Linux kernel.
If this breaks your laptop, please let me know how it does it :-)
Approved by: njl (mentor)
workaround was for hardware where the clock was not latched, not for
hardware that was too slow. Also, make variable names more specific for ddb
printing.
what the ACPI-safe workaround is intended to fix. Requested by phk.
Set the bushandle and tag when attaching the timer, don't do it each time
in read_counter(). Pointed out by bde.
Move test_counter() to the end. Staticize acpi_timer_reg.
supported. Symptoms of this bug included unnecessary use of ACPI-safe
and a dmesg that has deltas of about 2^24:
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 16777210, width = 16777208
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
To fix this:
* Use a 32 bit timecounter mask when the timer is 32 bits.
* In test_counter(), use the acpi_TimerDelta function which handles 24/32
bit timers and wraparound.
Miscellaneous fixes:
* Use C99 initializers for timecounter struct.
* Use u_int and uint32_t where appropriate instead of unsigned.
* Remove whitespace-only lines
* Remove the old PIIX4 PCI workaround. The timecounter testing code has
been in use for long enough to prove it's functional.
globally available. acpi_TimerDelta() subtracts two readings from the
ACPI PM timer and returns the difference. It properly distinguishes between
24-bit and 32-bit timers and handles wraparound.
a NULL crsbuf pointer. This shouldn't happen if it returns AE_OK. We'll
figure out why this is happening later.
Submitted by: Bruno Ducrot <ducrot@poupinou.org>
