come up as 't6nex' nexus devices with 'cc' ports hanging off them.
The T6 firmware and configuration files will be added as soon as they
are released. For now the driver will try to work with whatever
firmware and configuration is on the card's flash.
Sponsored by: Chelsio Communications
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
If a packet contains the Ethernet header (14 bytes) in the first mbuf
and the payload (IP + UDP + data) in the second mbuf, then the attempt
to fetch the l3hdr will return a NULL pointer. The first loop iteration
will drop len to zero and exit the loop without setting 'p'. However,
the desired data is at the start of the second mbuf, so the correct
behavior is to loop around and let the conditional set 'p' to m_data of
the next mbuf (and leave offset as 0).
Reviewed by: np
Sponsored by: Chelsio Communications
transfers.
The Initiator and Target both perform zero copy receive for transfers
greater than or equal to this threshold.
Sponsored by: Chelsio Communications
routines available in t4_tom to manage the iSCSI DDP page pod region.
This adds the ability to use multiple DDP page sizes to the iSCSI
driver, among other improvements.
Sponsored by: Chelsio Communications
The device quiet flag is not automatically reset on detach, so it is
inherited by other device drivers (e.g. when switching a device driver
over to ppt for PCI pass through). Cope with this behavior by explicitly
marking the device verbose during detach so that the next driver can make
its own decision.
Sponsored by: Chelsio Communications
- Return appropriate error code instead of ENOMEM when sosend() fails in
send_mpa_req.
- Fix for problematic race during destroy_qp.
- Abortive close in the failure of send_mpa_reject() instead of normal close.
- Remove the unnecessary doorbell flowcontrol logic.
Submitted by: Krishnamraju Eraparaju at Chelsio
MFC after: 1 month
Sponsored by: Chelsio communications
hardware send and receive PDU limits. Report these limits to ICL and
take them into account when setting the socket's send and receive buffer
sizes. The driver used a single hardcoded limit everywhere prior to
this change.
Sponsored by: Chelsio Communications
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
This permits a single early return for VF devices in the routines that
add sysctl nodes.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7512
