o catch one place where we were not using ath_chan_change to
switch channels; this fixes a problem where the channel
settings were not being correctly reported in captured packets
o return unique channel identification in the channel flags;
ethereal gets confused if you return merged flags (e.g. ofdm,
cck, and 2Ghz) (this is workaround and should be removed if
we can ever cleanup radiotap consumers)
o correct short/long preamble flag state for rx and treat tx
the same--use a new hwflags array that gives us the data
based on the h/w rate index/cookie
o add gross hack to handle radiotap capture of frames that
come in with hardware padding; should be replaced by a
flag in the radiotap header and more smarts in the apps
that decode radiotap data
o lintval is in ms; must convert to TU's for passing to the hal
o roundup to calculate nexttbtt (should look at current tsf and pull the
calculated nextbtt forward but this'll do for now)
o don't or- in HAL_BEACON_RESET_TSF when doing station timer setup; this
is not needed and messes up the sleep timer calcs, though it's unclear
if it mattered as the hal masks these values before use
Submitted by: Thorsten von Eicken
special-purpose code to display status for an interface for
state that was not address-oriented. This status reporting
was merged in to the address-oriented status reporting but
did not work for link address reporting (as discovered with
fwip interfaces). Correct this mis-merge and eliminate the
bogus kludge that was used for link-level address reporting.
o add an af_other_status method for an address family for
reporting status of things like media, vlan, etc.
o call the af_other_status methods after reporting address
status for an interface
o special-case link address status; when reporting all
status for an interface invoke it specially prior to
reporting af_other_status methods (since it requires the
sockaddr_dl that is passed in to status separately from
the rtmsg address state)
o correct the calling convention for link address status;
don't cast types, construct the proper parameter
This fixes ifconfig on fwip interfaces.
netstat(1):
- Make previously unnecessarily global variables local.
- Use LIST_FOREACH() in preference to manual iteration.
- Restore a sanity check through slightly incestuous use of queue macro
knowledge.
Submitted by: rik
the netperf branch but for some reason didn't trigger a build failure
locally when I merged to CVS and omitted it. Presumably driver error.
Pointed out by: cperciva, tinderbox
for calculating the job number for a job based on the control-file name.
We might receive cf-files named by other implementations of lpr, where
the job number shown by lpq would not match the job number that other
commands expected for the same name.
This also uses a newer algorithm for determining a job number, to avoid
problems caused when a control-file is named using an IP address, instead
of the hostname.
This also moved the declaration if isowner() from lp.h to rmjob.c. When I
went to change the parameters, I noticed that rmjob.c was the only source
file which uses it.
MFC after: 2 weeks
home-brew linked lists. Read in the ipxpcb_list structure first in
order to find the first pcb pointer. Then follow the chain as
before, only the termination condition is a NULL next pointer
rather than a next pointer equal to the original offset.
control-file for each print job. This is partially because the previous
checks still let through some characters which would cause trouble for
other applications which try to process the resulting userid -- such as
accounting programs.
But the main reason is to handle the case where some remote host sends a
print job where the given userid is an uppercase-version of the real userid.
For that case, lpd will now check for uppercase letters in the userid. If
there are any, it will check to see if the given userid (with the uppercase
letters) is a valid one. If it is *not* valid, then lpd will change the
userid to all-lowercase right when the job is received.
MFC after: 2 weeks
schedulers a bit to ensure more correct handling of priorities and fewer
priority inversions:
- Add two functions to the sched(9) API to handle priority lending:
sched_lend_prio() and sched_unlend_prio(). The turnstile code uses these
functions to ask the scheduler to lend a thread a set priority and to
tell the scheduler when it thinks it is ok for a thread to stop borrowing
priority. The unlend case is slightly complex in that the turnstile code
tells the scheduler what the minimum priority of the thread needs to be
to satisfy the requirements of any other threads blocked on locks owned
by the thread in question. The scheduler then decides where the thread
can go back to normal mode (if it's normal priority is high enough to
satisfy the pending lock requests) or it it should continue to use the
priority specified to the sched_unlend_prio() call. This involves adding
a new per-thread flag TDF_BORROWING that replaces the ULE-only kse flag
for priority elevation.
- Schedulers now refuse to lower the priority of a thread that is currently
borrowing another therad's priority.
- If a scheduler changes the priority of a thread that is currently sitting
on a turnstile, it will call a new function turnstile_adjust() to inform
the turnstile code of the change. This function resorts the thread on
the priority list of the turnstile if needed, and if the thread ends up
at the head of the list (due to having the highest priority) and its
priority was raised, then it will propagate that new priority to the
owner of the lock it is blocked on.
Some additional fixes specific to the 4BSD scheduler include:
- Common code for updating the priority of a thread when the user priority
of its associated kse group has been consolidated in a new static
function resetpriority_thread(). One change to this function is that
it will now only adjust the priority of a thread if it already has a
time sharing priority, thus preserving any boosts from a tsleep() until
the thread returns to userland. Also, resetpriority() no longer calls
maybe_resched() on each thread in the group. Instead, the code calling
resetpriority() is responsible for calling resetpriority_thread() on
any threads that need to be updated.
- schedcpu() now uses resetpriority_thread() instead of just calling
sched_prio() directly after it updates a kse group's user priority.
- sched_clock() now uses resetpriority_thread() rather than writing
directly to td_priority.
- sched_nice() now updates all the priorities of the threads after the
group priority has been adjusted.
Discussed with: bde
Reviewed by: ups, jeffr
Tested on: 4bsd, ule
Tested on: i386, alpha, sparc64
- ipx_pcbnotify(), which is never called.
- ipx_rtchange(), which is never called, is incomplete inplemented, and
also #ifdef notdef.
- spx_fixmtu(), which is never called, is incompletely implemented, and
also #ifdef notdef.
other comments. Clarify that the next two things needed for SMP are
two lines.
- Expand mii abbreviation to miibus for clarity in the USB ethernet
comment.
is the case for most other sysctls in the System V IPC message queue
implementation.
PR: 75541
Submitted by: Sergiy Vyshnevetskiy <serg at vostok dot net>
MFC after: 2 weeks
