ahc_eisa.c:
ahc_pci.c:
Conform to new aic7xxx IRQ API.
Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.
aic7770.c:
Disable card generated interrupt early in our probe for
"extra safety"
Commonize some seeprom code with the PCI side of the driver.
aic7xxx.c:
Correctly initialize a few scratch ram locations during
a sequencer restart. This avoids spurious sequencer ram
parity errors in some configurations.
Include the softc in ahc_update_residual calls. We need it
for some diagnostics in this code path.
Flag a data overrun on an auto-request sense failure as a
CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.
Force a renegotiation after noticing a parity error. This
covers targets that lose our negotiation settings but don't
bother to give us a unit attention condition. This can happen
if a target fails during a reselection of us during a cable
pull.
Convert some code to using constants.
Fix some typos.
Correct target mode message loop handling. ahc_clear_msg_state
was not clearing the "need to go to message out phase" bit once
our loop was over.
Simplify some abort handling code.
Include tag information in target mode immediate notify events.
When shutting down EISA controllers, don't EISA BIOS settings in
the high portions of scratch ram. This fixes warm boot issues on
some systems.
Save a bit of space by only allocating the SCBs that we can use.
Avoid some code paths in ahc_abort_scbs() if we are currently
acting as a target.
Correctly cleanup stranded SCBs in the card's SCB array. These
are SCBs who's mapping has already been torn down by code that
aborted the SCB by seeing it in another list first.
Add a comment about some potential bus reset issues for target
mode on Twin (EISA only) controllers.
aic7xxx.h:
Cleanup the hardware scb definitions a bit.
Allocate a ful 256 byte scb mapping index. This simplifies
the lookup code since the table covers all possible (and potentially
bogus) values.
Make AHC_DEBUG work again.
aic7xxx.reg:
Updates to hardware SCB definition.
New definitions for target mode fixes.
aic7xxx.seq:
In target mode, initialize SAVED_LUN just after we receive
the identify message. It may be required in the error recovery
path when a normal cdb packet (includes lun) is not sent up to
the host for processing.
Respond to irregular messages during a selection in target mode.
Defer looking for space for a cdb packet until we are about to
enter command phase. We want to be able to handle irregular messages
even if we would otherwise return QUEUE_FULL or BUSY.
Add support for sending Ignore Wide Residue messages as a target.
In the disable disconnect case in target mode, set our transfer
rate correctly once data are availble.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Add the ability to write and erase the seeprom.
aic7xxx_inline.h:
Correct Big Endian handling of large cdb sizes (> 12 bytes).
Adaptec to changes in the calc_residual API.
Correct a target mode bug where we always attempted to service
the input queue even if no progress could be made due to lack
of ATIOs.
aic7xxx_osm.c:
Adaptec to new IRQ mapping API. The new API allows the core
to only enable our IRQ mapping once it is safe (sufficient
initialization) to do so.
Slap bootverbose protection around some diagnostics.
Only attempt DT phases if we are wide.
aic7xxx_osm.h:
Enable big endian support.
Adjust for IRQ API change.
aic7xxx_pci.c:
Be more careful about relying on subvendor 9005 information.
We now only trust it for HBAs. This should allow the driver
to attach to some MBs where the subvendor/device information
does not follow the Adaptec spec.
Only enable interrupts on the card once we are fully setup.
Disable external SCB ram usage on the aic7895. I have not
been able to make it 100% reliable.
Adjust to seeprom routines being properly prefixed with "ahc".
Fix a few bugs in the external SCB ram probing routine. We
need to clear any parity errors we've triggered during the
probe to avoid future, fatal, interrupts.
If we detect an invalid cable combination, pretent there are
no cable at all. This will enable all of the terminators
which is probably the safest configuration we can "guess".
MFC after: 4 days
-stable machine via the old-school methods):
Use __FreeBSD_version in preference to __FreeBSD__ >= N where possible.
Define a single variable mythread which is set to curproc or curthread
depending on the OS version (with a comment saying it is a white lie on
4.x since it really is a proc).
NB: __FreeBSD__ is the OS level of the host machine, not the target,
and should never be used, if possible, as __FreeBSD__ >= N.
Rev 1.56 of if_dc.c removed calls to mii_pollstat() from the dc_tick()
routine. dc_tick() is called regularly to detect link up and link down
status, especially when autonegotiating.
The expectation was that mii_tick() (which is still called from dc_tick())
would update status information automatically in all cases where it would
be sensible to do so.
Unfortunately, with authentic 21143 chips this is not the case, and
the driver never successfully autonegotiates. This is because (despite
what it says in the 21143 manual) the chip always claims that link is not
present while the autonegotiation enable bit is set. Autonegotation takes
place and succeeds, but the driver tests the link bits before it switches
off the autonegotiation enable bit, and success is not recognised.
The simplest solution is to call dcphy_status() more often for MII_TICK
calls by dropping out of the switch statement instead of exiting when
we are autonegotiating and link appears to not be present. When
autonegotiation succeeds, dcphy_status() will note the speed and fdx/hdx
state and turn off the autonegotiation enable bit. The next call to
dcphy_status() will notice that link is present, and the dc driver code
will be notified.
Macronix chips also use this code, but implement link detection as
described in the manual, and hence don't need this patch. However, tests
on a Macronix 98715AEC-C show that it does not adversely affect them.
This could be done better but is the minimal effective change, and most
closely mimics what was happening prior to rev 1.56 of if_dc.c. (Actually
I also deleted a small amount of unnecessary code while I was in the area.)
Reviewed by: wpaul
loop is inversly proportional to hz.
This makes things more sane for configurations with hz != 100.
Cosmetic: Make the loops look similar to the loops in digi.c
loop is inversly proportional to hz.
This makes things more sane for configurations with hz > 100.
Submitted by: Peter Jeremy <peter.jeremy@alcatel.com.au>
environment needed at boot time to a dynamic subsystem when VM is
up. The dynamic kernel environment is protected by an sx lock.
This adds some new functions to manipulate the kernel environment :
freeenv(), setenv(), unsetenv() and testenv(). freeenv() has to be
called after every getenv() when you have finished using the string.
testenv() only tests if an environment variable is present, and
doesn't require a freeenv() call. setenv() and unsetenv() are self
explanatory.
The kenv(2) syscall exports these new functionalities to userland,
mainly for kenv(1).
Reviewed by: peter
- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
lun address modifier of sorts. Only an HP XP-512 seems to have cared.
Fix a few misplaced pointers for the new fabric goop, which has been
demonstrated to work on newer Brocades and McData switches now.
Put in commented out code which would run GFF_ID if the QLogic f/w
allowed it.
Don't whine about not being able to find a handle for a command if it
was a command aborted (by us).
o move timeout from wihap_info to wihap_sta_info
o sprinkle spls into the code (need to use proper -current locking)
o better use of le16toh and htole16
o fix a few leaks m_freem(m)
o minor knf
o minor de-knf to match OpenBSD
o de__P
- Add a device_method_t array, fore_methods.
- Add a fore_ident_table that contains the various FORE Systems PCA-200
series devices.
- Rewrite of the fore_probe routine (formerly known as fore_pci_probe).
- Minor changes... mostly WIP stuff to get this updated... still much to
be done.
the per-channel bus_addr_t offset. Also, cast the offset to (long long)
and use %#llx instead of %#x to fix printf warnings on architectures where
sizeof(bus_addr_t) != sizeof(int).
es137x.c: In function `es1371_rdcd':
es137x.c:598: warning: `x' might be used uninitialized in this function
PR: kern/35408
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
that declares itself to be a disk, which may be the wrong thing to do in
the long term but it works well enough to attach to emulated disks in the
PowerPC simulator in gdb now that they have the proper device_type
property.
The extra microphone channel capability is part of the "normal" ac97
capabilities and not an extended ac97 capability. Now recording on
codecs without a seperate mic channel works.
MFC after: 1 week
FIFO or the in-RAM descriptors it will switch to RX_IDLE from where it
is not restarted.
We used to deal with RX_IDLE by doing a total reinit but this lost
our link and caused a potential 30sec autonegotiation against
switches. This was changed to a less heavyhanded approach, but this
failed to restart the receiver it it were in the RX_IDLE state.
This change adds the RX_IDLE and the RX_FIFO_OFLOW conditions as
triggers for interrupts and receive side processing, and restarts
the receiver when it is RX_IDLE.
Remove the #ifdef notyet'ed nge_rxeoc() function.
Sponsored by: Cybercity Internet, Denmark.
MFC after: 7 days
