When using lagg failover mode neither Gratuitous ARP (IPv4) or Unsolicited
Neighbour Advertisements (IPv6) are sent to notify other nodes that the
address may have moved.
This results is slow failover, dropped packets and network outages for the
lagg interface when the primary link goes down.
We now use the new if_link_state_change_cond with the force param set to
allow lagg to force through link state changes and hence fire a
ifnet_link_event which are now monitored by rip and nd6.
Upon receiving these events each protocol trigger the relevant
notifications:
* inet4 => Gratuitous ARP
* inet6 => Unsolicited Neighbour Announce
This also fixes the carp IPv6 NA's that stopped working after r251584 which
added the ipv6_route__llma route.
The new behavour can be controlled using the sysctls:
* net.link.ether.inet.arp_on_link
* net.inet6.icmp6.nd6_on_link
Also removed unused param from lagg_port_state and added descriptions for the
sysctls while here.
PR: 156226
MFC after: 1 month
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D4111
Before r291643, adding new interface prefix had the following logic:
try_add:
EEXIST && (PINNED) {
try_del(w/o PINNED flag)
if (OK)
try_add(PINNED)
}
In r291643, deletion was performed w/ PINNED flag held which leaded
to new interface prefixes (like ::1) overriding older ones.
Fix this by requesting deletion w/o RTF_PINNED.
PR: kern/205285
Submitted by: Fabian Keil <fk at fabiankeil.de>
LLE structure is mostly unchanged during its lifecycle: there are only 2
things relevant for fast path lookup code:
1) link-level address change. Since r286722, these updates are performed
under AFDATA WLOCK.
2) Some sort of feedback indicating that this particular entry is used so
we send NS to perform reachability verification instead of expiring entry.
The only signal that is needed from fast path is something like binary
yes/no.
The latter is solved by the following changes:
Special r_skip_req (introduced in D3688) value is used for fast path feedback.
It is read lockless by fast path, but updated under req_mutex mutex. If this
field is non-zero, then fast path will acquire lock and set it back to 0.
After transitioning to STALE state, callout timer is armed to run each
V_nd6_delay seconds to make sure that if packet was transmitted at the start
of given interval, we would be able to switch to PROBE state in V_nd6_delay
seconds as user expects.
(in STALE state) timer is rescheduled until original V_nd6_gctimer expires
keeping lle in STALE state (remaining timer value stored in lle_remtime).
(in STALE state) timer is rescheduled if packet was transmitted less that
V_nd6_delay seconds ago to make sure we transition to PROBE state exactly
after V_n6_delay seconds.
As a result, all packets towards lle in REACHABLE/STALE/PROBE states are handled
by fast path without acquiring lle read lock.
Differential Revision: https://reviews.freebsd.org/D3780
Vast majority of rtalloc(9) users require only basic info from
route table (e.g. "does the rtentry interface match with the interface
I have?". "what is the MTU?", "Give me the IPv4 source address to use",
etc..).
Instead of hand-rolling lookups, checking if rtentry is up, valid,
dealing with IPv6 mtu, finding "address" ifp (almost never done right),
provide easy-to-use API hiding all the complexity and returning the
needed info into small on-stack structure.
This change also helps hiding route subsystem internals (locking, direct
rtentry accesses).
Additionaly, using this API improves lookup performance since rtentry is not
locked.
(This is safe, since all the rtentry changes happens under both radix WLOCK
and rtentry WLOCK).
Sponsored by: Yandex LLC
LLE structure is mostly unchanged during its lifecycle.
To be more specific, there are 2 things relevant for fast path
lookup code:
1) link-level address change. Since r286722, these updates are performed
under AFDATA WLOCK.
2) Some sort of feedback indicating that this particular entry is used so
we re-send arp request to perform reachability verification instead of
expiring entry. The only signal that is needed from fast path is something
like binary yes/no.
The latter is solved by the following changes:
1) introduce special r_skip_req field which is read lockless by fast path,
but updated under (new) req_mutex mutex. If this field is non-zero, then
fast path will acquire lock and set it back to 0.
2) introduce simple state machine: incomplete->reachable<->verify->deleted.
Before that we implicitely had incomplete->reachable->deleted state machine,
with V_arpt_keep between "reachable" and "deleted". Verification was performed
in runtime 5 seconds before V_arpt_keep expire.
This is changed to "change state to verify 5 seconds before V_arpt_keep,
set r_skip_req to non-zero value and check it every second". If the value
is zero - then send arp verification probe.
These changes do not introduce any signifficant control plane overhead:
typically lle callout timer would fire 1 time more each V_arpt_keep (1200s)
for used lles and up to arp_maxtries (5) for dead lles.
As a result, all packets towards "reachable" lle are handled by fast path without
acquiring lle read lock.
Additional "req_mutex" is needed because callout / arpresolve_slow() or eventhandler
might keep LLE lock for signifficant amount of time, which might not be feasible
for fast path locking (e.g. having rmlock as ether AFDATA or lltable own lock).
Differential Revision: https://reviews.freebsd.org/D3688
by filter function instead of picking into routing table details in
each consumer.
Remove now-unused rt_expunge() (eliminating last external RTF_RNH_LOCKED
user).
This simplifies future nexthops/mulitipath changes and rtrequest1_fib()
locking refactoring.
Actual changes:
Add "rt_chain" field to permit rte grouping while doing batched delete
from routing table (thus growing rte 200->208 on amd64).
Add "rti_filter" / "rti_filterdata" / "rti_spare" fields to rt_addrinfo
to pass filter function to various routing subsystems in standard way.
Convert all rt_expunge() customers to new rt_addinfo-based api and eliminate
rt_expunge().
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
new return codes of -1 were mistakenly being considered "true". Callout_stop
now returns -1 to indicate the callout had either already completed or
was not running and 0 to indicate it could not be stopped. Also update
the manual page to make it more consistent no non-zero in the callout_stop
or callout_reset descriptions.
MFC after: 1 Month with associated callout change.
Add net.link.lagg.lacp.default_strict_mode which defines
the default value for LACP strict compliance for created
lagg devices.
Also:
* Add lacp_strict option to ifconfig(8).
* Fix lagg(4) creation examples.
* Minor style(9) fix.
MFC after: 1 week
sysctl and will always be on. The former split between default and
fast forwarding is removed by this commit while preserving the ability
to use all network stack features.
Differential Revision: https://reviews.freebsd.org/D4042
Reviewed by: ae, melifaro, olivier, rwatson
MFC after: 1 month
Sponsored by: Rubicon Communications (Netgate)
IPv4 packets (when it should return FALSE). It happens because PF_ANEQ() doesn't
stop if first 32 bits of IPv4 packets are equal and starts to check next 3*32
bits (like for IPv6 packet). Those bits containt some garbage and in result
PF_ANEQ() wrongly returns TRUE.
Fix: Check if packet is of AF_INET type and if it is then compare only first 32
bits of data.
PR: 204005
Submitted by: Miłosz Kaniewski
In certain configurations (mostly but not exclusively as a VM on Xen) pf
produced packets with an invalid TCP checksum.
The problem was that pf could only handle packets with a full checksum. The
FreeBSD IP stack produces TCP packets with a pseudo-header checksum (only
addresses, length and protocol).
Certain network interfaces expect to see the pseudo-header checksum, so they
end up producing packets with invalid checksums.
To fix this stop calculating the full checksum and teach pf to only update TCP
checksums if TSO is disabled or the change affects the pseudo-header checksum.
PR: 154428, 193579, 198868
Reviewed by: sbruno
MFC after: 1 week
Relnotes: yes
Sponsored by: RootBSD
Differential Revision: https://reviews.freebsd.org/D3779
The remove began with revision r271733.
NOTE: This patch must never be merge to 10-Stable
Reviewed by: glebius
Approved by: bapt (mentor)
Relnotes: Yes
Sponsored by: EuroBSDCon Sweden.
Differential Revision: D3786
Initially function was introduced in r53541 (KAME initial commit) to
"provide hints from upper layer protocols that indicate a connection
is making "forward progress"" (quote from RFC 2461 7.3.1 Reachability
Confirmation).
However, it was converted to do nothing (e.g. just return) in r122922
(tcp_hostcache implementation) back in 2003. Some defines were moved
to tcp_var.h in r169541. Then, it was broken (for non-corner cases)
by r186119 (L2<>L3 split) in 2008 (NULL ifp in nd6_lookup). So,
right now this code is broken and has no "real" base users.
Differential Revision: https://reviews.freebsd.org/D3699
Problem description:
How do we currently perform layer 2 resolution and header imposition:
For IPv4 we have the following chain:
ip_output() -> (ether|atm|whatever)_output() -> arpresolve()
Lookup is done in proper place (link-layer output routine) and it is possible
to provide cached lle data.
For IPv6 situation is more complex:
ip6_output() -> nd6_output() -> nd6_output_ifp() -> (whatever)_output() ->
nd6_storelladdr()
We have ip6_ouput() which calls nd6_output() instead of link output routine.
nd6_output() does the following:
* checks if lle exists, creates it if needed (similar to arpresolve())
* performes lle state transitions (similar to arpresolve())
* calls nd6_output_ifp() which pushes packets to link output routine along
with running SeND/MAC hooks regardless of lle state
(e.g. works as run-hooks placeholder).
After that, iface output routine like ether_output() calls nd6_storelladdr()
which performs lle lookup once again.
As a result, we perform lookup twice for each outgoing packet for most types
of interfaces. We also need to maintain runtime-checked table of 'nd6-free'
interfaces (see nd6_need_cache()).
Fix this behavior by eliminating first ND lookup. To be more specific:
* make all nd6_output() consumers use nd6_output_ifp() instead
* rename nd6_output[_slow]() to nd6_resolve_[slow]()
* convert nd6_resolve() and nd6_resolve_slow() to arpresolve() semantics,
e.g. copy L2 address to buffer instead of pushing packet towards lower
layers
* Make all nd6_storelladdr() users use nd6_resolve()
* eliminate nd6_storelladdr()
The resulting callchain is the following:
ip6_output() -> nd6_output_ifp() -> (whatever)_output() -> nd6_resolve()
Error handling:
Currently sending packet to non-existing la results in ip6_<output|forward>
-> nd6_output() -> nd6_output _lle() which returns 0.
In new scenario packet is propagated to <ether|whatever>_output() ->
nd6_resolve() which will return EWOULDBLOCK, and that result
will be converted to 0.
(And EWOULDBLOCK is actually used by IB/TOE code).
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D1469
* prepare gateway before insertion
* use RTM_CHANGE instead of explicit find/change route
* Remove fib argument from ifa_switch_loopback_route added in r264887:
if old ifp fib differes from new one, that the caller
is doing something wrong
* Make ifa_*_loopback_route call single ifa_maintain_loopback_route().
On receipt of a redirect message, install an interface route for the
redirected destination. On removal of the corresponding Neighbor Cache
entry, remove the interface route.
This requires changes in rtredirect_fib() to cope with an AF_LINK
address for the gateway and with the absence of RTF_GATEWAY.
This fixes the "Redirected On-Link" test cases in the Tahi IPv6 Ready Logo
Phase 2 test suite.
Unrelated to the above, fix a recursion on the radix node head lock
triggered by the Tahi Redirected to Alternate Router test cases.
When I first wrote this patch in October 2012, all Section 2
(Neighbor Discovery) test cases passed on 10-CURRENT, 9-STABLE,
and 8-STABLE. cem@ recently rebased the 10.x patch onto head and reported
that it passes Tahi. (Thanks!)
These other test cases also passed in 2012:
* the RTF_MODIFIED case, with IPv4 and IPv6 (using a
RTF_HOST|RTF_GATEWAY route for the destination)
* the redirected-to-self case, with IPv4 and IPv6
* a valid IPv4 redirect
All testing in 2012 was done with WITNESS and INVARIANTS.
Tested by: EMC / Isilon Storage Division via Conrad Meyer (cem) in 2015,
Mark Kelley <mark_kelley@dell.com> in 2012,
TC Telkamp <terence_telkamp@dell.com> in 2012
PR: 152791
Reviewed by: melifaro (current rev), bz (earlier rev)
Approved by: kib (mentor)
MFC after: 1 month
Relnotes: yes
Sponsored by: Dell Inc.
Differential Revision: https://reviews.freebsd.org/D3602
without holding afdata wlock
* convert per-af delete_address callback to global lltable_delete_entry() and
more low-level "delete this lle" per-af callback
* fix some bugs/inconsistencies in IPv4/IPv6 ifscrub procedures
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D3573
To make driver programming easier the TSO limits are changed to
reflect the values used in the BUSDMA tag a network adapter driver is
using. The TCP/IP network stack will subtract space for all linklevel
and protocol level headers and ensure that the full mbuf chain passed
to the network adapter fits within the given limits.
Implementation notes:
If a network adapter driver needs to fixup the first mbuf in order to
support VLAN tag insertion, the size of the VLAN tag should be
subtracted from the TSO limit. Else not.
Network adapters which typically inline the complete header mbuf could
technically transmit one more segment. This patch does not implement a
mechanism to recover the last segment for data transmission. It is
believed when sufficiently large mbuf clusters are used, the segment
limit will not be reached and recovering the last segment will not
have any effect.
The current TSO algorithm tries to send MTU-sized packets, where the
MTU typically is 1500 bytes, which gives 1448 bytes of TCP data
payload per packet for IPv4. That means if the TSO length limitiation
is set to 65536 bytes, there will be a data payload remainder of
(65536 - 1500) mod 1448 bytes which is equal to 324 bytes. Trying to
recover total TSO length due to inlining mbuf header data will not
have any effect, because adding or removing the ETH/IP/TCP headers
to or from 324 bytes will not cause more or less TCP payload to be
TSO'ed.
Existing network adapter limits will be updated separately.
Differential Revision: https://reviews.freebsd.org/D3458
Reviewed by: rmacklem
MFC after: 2 weeks
Some places in our network stack already have const
arguments (like if_output() routines and LLE functions).
Code using ifa_ifwith (and similar functins) along with
LLE/_output functions is currently bound to use tricks
like __DECONST(). Provide a cleaner way by making sockaddr
lookup key really constant.
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D3464
The crop/drop-ovl fragment scrub modes are not very useful and likely to confuse
users into making poor choices.
It's also a fairly large amount of complex code, so just remove the support
altogether.
Users who have 'scrub fragment crop|drop-ovl' in their pf configuration will be
implicitly converted to 'scrub fragment reassemble'.
Reviewed by: gnn, eri
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D3466
CoDel is a parameterless queue discipline that handles variable bandwidth
and RTT.
It can be used as the single queue discipline on an interface or as a sub
discipline of existing queue disciplines such as PRIQ, CBQ, HFSC, FAIRQ.
Differential Revision: https://reviews.freebsd.org/D3272
Reviewd by: rpaulo, gnn (previous version)
Obtained from: pfSense
Sponsored by: Rubicon Communications (Netgate)
Before that, the logic besides lle_create() was the following:
return existing if found, create if not. This behaviour was error-prone
since we had to deal with 'sudden' static<>dynamic lle changes.
This commit fixes bunch of different issues like:
- refcount leak when lle is converted to static.
Simple check case:
console 1:
while true;
do for i in `arp -an|awk '$4~/incomp/{print$2}'|tr -d '()'`;
do arp -s $i 00:22:44:66:88:00 ; arp -d $i;
done;
done
console 2:
ping -f any-dead-host-in-L2
console 3:
# watch for memory consumption:
vmstat -m | awk '$1~/lltable/{print$2}'
- possible problems in arptimer() / nd6_timer() when dropping/reacquiring
lock.
New logic explicitly handles use-or-create cases in every lla_create
user. Basically, most of the changes are purely mechanical. However,
we explicitly avoid using existing lle's for interface/static LLE records.
* While here, call lle_event handlers on all real table lle change.
* Create lltable_free_entry() calling existing per-lltable
lle_free_t callback for entry deletion
This permits us having all (not fully true yet) all the info
needed in lookup process in first 64 bytes of 'struct llentry'.
struct llentry layout:
BEFORE:
[rwlock .. state .. state .. MAC ] (lle+1) [sockaddr_in[6]]
AFTER
[ in[6]_addr MAC .. state .. rwlock ]
Currently, address part of struct llentry has only 16 bytes for the key.
However, lltable does not restrict any custom lltable consumers with long
keys use the previous approach (store key at (lle+1)).
Sponsored by: Yandex LLC
* Split lltable_init() into lltable_allocate_htbl() (alloc
hash table with default callbacks) and lltable_link() (
links any lltable to the list).
* Switch from LLTBL_HASHTBL_SIZE to per-lltable hash size field.
* Move lltable setup to separate functions in in[6]_domifattach.
differences between projects/routing and HEAD.
This commit tries to keep code logic the same while changing underlying
code to use unified callbacks.
* Add llt_foreach_entry method to traverse all entries in given llt
* Add llt_dump_entry method to export particular lle entry in sysctl/rtsock
format (code is not indented properly to minimize diff). Will be fixed
in the next commits.
* Add llt_link_entry/llt_unlink_entry methods to link/unlink particular lle.
* Add llt_fill_sa_entry method to export address in the lle to sockaddr
format.
* Add llt_hash method to use in generic hash table support code.
* Add llt_free_entry method which is used in llt_prefix_free code.
* Prepare for fine-grained locking by separating lle unlink and deletion in
lltable_free() and lltable_prefix_free().
* Provide lltable_get<ifp|af>() functions to reduce direct 'struct lltable'
access by external callers.
* Remove @llt agrument from lle_free() lle callback since it was unused.
* Temporarily add L3_CADDR() macro for 'const' sockaddr typecasting.
* Switch to per-af hashing code.
* Rename LLE_FREE_LOCKED() callback from in[6]_lltable_free() to
in_[6]lltable_destroy() to avoid clashing with llt_free_entry() method.
Update description from these functions.
* Use unified lltable_free_entry() function instead of per-af one.
Reviewed by: ae
* Move interface route cleanup to route.c:rt_flushifroutes()
* Convert most of "for (fibnum = 0; fibnum < rt_numfibs; fibnum++)" users
to use new rt_foreach_fib() instead of hand-rolling cycles.
* Move lle creation/deletion from lla_lookup to separate functions:
lla_lookup(LLE_CREATE) -> lla_create
lla_lookup(LLE_DELETE) -> lla_delete
lla_create now returns with LLE_EXCLUSIVE lock for lle.
* Provide typedefs for new/existing lltable callbacks.
Reviewed by: ae
The filter is called from the network hot path and must not sleep.
The filter runs with the descriptor lock held and does not manipulates the
buffers, so it is not necessary sleep when the hold buffer is in use.
Just ignore the hold buffer contents when it is being copied to user space
(when hold buffer in use is set).
This fix the "Sleeping thread owns a non-sleepable lock" panic when the
userland thread is too busy reading the packets from bpf(4).
PR: 200323
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
The first one never triggers because bpf_canfreebuf() can only be true for
zero-copy buffers and zero-copy buffers are not read with read(2).
The second also never triggers, because we check the free buffer before
calling ROTATE_BUFFERS(). If the hold buffer is in use the free buffer
will be NULL and there is nothing else to do besides drop the packet. If
the free buffer isn't NULL the hold buffer _is_ free and it is safe to
rotate the buffers.
Update the comment in ROTATE_BUFFERS macro to match the logic described
here.
While here fix a few typos in comments.
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
The buffer must be allocated (or even changed) before the interface is set
and thus, there is no need to verify if the buffer is in use.
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
the buffer is allocated we are committed to a particular buffer method
(BPF_BUFMODE_BUFFER in this case).
If we are using zero-copy buffers, the userland program must register its
buffers before set the interface.
If we are using kernel memory buffers, we can allocate the buffer at the
time that the interface is being set.
This fix allows the usage of BIOCSETBUFMODE after r235746.
Update the comments to reflect the recent changes.
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
still on going, but it has passed world for mips and powerpc...
I know this has an extra semicolon, but this is the patch that is
tested...
Looks like better fix is to use _Static_assert...
use CTASSERTs now that we have them...
Replace a draft w/ RFC that's over 10 years old.
Note that _AALG and _EALG do not need to match what the IKE daemons
think they should be.. This is part of the KABI... I decided to
renumber AESCTR, but since we've never had working AESCTR mode, I'm
not really breaking anything.. and it shortens a loop by quite
a bit..
remove SKIPJACK IPsec support... SKIPJACK never made it out of draft
(in 1999), only has 80bit key, NIST recommended it stop being used
after 2010, and setkey nor any of the IKE daemons I checked supported
it...
jmgurney/ipsecgcm: a357a33, c75808b, e008669, b27b6d6
Reviewed by: gnn (earlier version)
R_Free(). This matches the other macros and reduces the chances to clash
with other headers.
This also fixes the build of radix.c outside of the kernel environment.
Reviewed by: glebius
ip_encap already has inspected mbuf's data, at least an IP header.
And it is safe to use mtod() and do direct access to needed fields.
Add M_ASSERTPKTHDR() to gif_encapcheck(), since the code expects that
mbuf has a packet header.
Move the code from gif_validate[46] into in[6]_gif_encapcheck(), also
remove "martian filters" checks. According to RFC 4213 it is enough to
verify that the source address is the address of the encapsulator, as
configured on the decapsulator.
Reviewed by: melifaro
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Both are used to protect access to IP addresses lists and they can be
acquired for reading several times per packet. To reduce lock contention
it is better to use rmlock here.
Reviewed by: gnn (previous version)
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D3149
- Tweek man page.
- Remove all mention of RANDOM_FORTUNA. If the system owner wants YARROW or DUMMY, they ask for it, otherwise they get FORTUNA.
- Tidy up headers a bit.
- Tidy up declarations a bit.
- Make static in a couple of places where needed.
- Move Yarrow/Fortuna SYSINIT/SYSUNINIT to randomdev.c, moving us towards a single file where the algorithm context is used.
- Get rid of random_*_process_buffer() functions. They were only used in one place each, and are better subsumed into those places.
- Remove *_post_read() functions as they are stubs everywhere.
- Assert against buffer size illegalities.
- Clean up some silly code in the randomdev_read() routine.
- Make the harvesting more consistent.
- Make some requested argument name changes.
- Tidy up and clarify a few comments.
- Make some requested comment changes.
- Make some requested macro changes.
* NOTE: the thing calling itself a 'unit test' is not yet a proper
unit test, but it helps me ensure things work. It may be a proper
unit test at some time in the future, but for now please don't make
any assumptions or hold any expectations.
Differential Revision: https://reviews.freebsd.org/D2025
Approved by: so (/dev/random blanket)
This commit contains large contributions from Giuseppe Lettieri and
Stefano Garzarella, is partly supported by grants from Verisign and Cisco,
and brings in the following:
- fix zerocopy monitor ports and introduce copying monitor ports
(the latter are lower performance but give access to all traffic
in parallel with the application)
- exclusive open mode, useful to implement solutions that recover
from crashes of the main netmap client (suggested by Patrick Kelsey)
- revised memory allocator in preparation for the 'passthrough mode'
(ptnetmap) recently presented at bsdcan. ptnetmap is described in
S. Garzarella, G. Lettieri, L. Rizzo;
Virtual device passthrough for high speed VM networking,
ACM/IEEE ANCS 2015, Oakland (CA) May 2015
http://info.iet.unipi.it/~luigi/research.html
- fix rx CRC handing on ixl
- add module dependencies for netmap when building drivers as modules
- minor simplifications to device-specific routines (*txsync, *rxsync)
- general code cleanup (remove unused variables, introduce macros
to access rings and remove duplicate code,
Applications do not need to be recompiled, unless of course
they want to use the new features (monitors and exclusive open).
Those willing to try this code on stable/10 can just update the
sys/dev/netmap/*, sys/net/netmap* with the version in HEAD
and apply the small patches to individual device drivers.
MFC after: 1 month
Sponsored by: (partly) Verisign, Cisco
bd_hdrcmplt. As if_loop does not use link-level headers, its behavior
when used by bpfwrite() should be the same regardless of the state of
bd_hdrcmplt. Without this change, libpcap (and other BPF users that
work like it) fail when writing to loopback interfaces.
Differential Revision: https://reviews.freebsd.org/D2989
Reviewed by: gnn, melifaro
Approved by: jmallett (mentor)
MFC after: 3 days
Update setkey and libipsec to understand aes-gcm-16 as an
encryption method.
A partial commit of the work in review D2936.
Submitted by: eri
Reviewed by: jmg
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
* GENERAL
- Update copyright.
- Make kernel options for RANDOM_YARROW and RANDOM_DUMMY. Set
neither to ON, which means we want Fortuna
- If there is no 'device random' in the kernel, there will be NO
random(4) device in the kernel, and the KERN_ARND sysctl will
return nothing. With RANDOM_DUMMY there will be a random(4) that
always blocks.
- Repair kern.arandom (KERN_ARND sysctl). The old version went
through arc4random(9) and was a bit weird.
- Adjust arc4random stirring a bit - the existing code looks a little
suspect.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Redo read_random(9) so as to duplicate random(4)'s read internals.
This makes it a first-class citizen rather than a hack.
- Move stuff out of locked regions when it does not need to be
there.
- Trim RANDOM_DEBUG printfs. Some are excess to requirement, some
behind boot verbose.
- Use SYSINIT to sequence the startup.
- Fix init/deinit sysctl stuff.
- Make relevant sysctls also tunables.
- Add different harvesting "styles" to allow for different requirements
(direct, queue, fast).
- Add harvesting of FFS atime events. This needs to be checked for
weighing down the FS code.
- Add harvesting of slab allocator events. This needs to be checked for
weighing down the allocator code.
- Fix the random(9) manpage.
- Loadable modules are not present for now. These will be re-engineered
when the dust settles.
- Use macros for locks.
- Fix comments.
* src/share/man/...
- Update the man pages.
* src/etc/...
- The startup/shutdown work is done in D2924.
* src/UPDATING
- Add UPDATING announcement.
* src/sys/dev/random/build.sh
- Add copyright.
- Add libz for unit tests.
* src/sys/dev/random/dummy.c
- Remove; no longer needed. Functionality incorporated into randomdev.*.
* live_entropy_sources.c live_entropy_sources.h
- Remove; content moved.
- move content to randomdev.[ch] and optimise.
* src/sys/dev/random/random_adaptors.c src/sys/dev/random/random_adaptors.h
- Remove; plugability is no longer used. Compile-time algorithm
selection is the way to go.
* src/sys/dev/random/random_harvestq.c src/sys/dev/random/random_harvestq.h
- Add early (re)boot-time randomness caching.
* src/sys/dev/random/randomdev_soft.c src/sys/dev/random/randomdev_soft.h
- Remove; no longer needed.
* src/sys/dev/random/uint128.h
- Provide a fake uint128_t; if a real one ever arrived, we can use
that instead. All that is needed here is N=0, N++, N==0, and some
localised trickery is used to manufacture a 128-bit 0ULLL.
* src/sys/dev/random/unit_test.c src/sys/dev/random/unit_test.h
- Improve unit tests; previously the testing human needed clairvoyance;
now the test will do a basic check of compressibility. Clairvoyant
talent is still a good idea.
- This is still a long way off a proper unit test.
* src/sys/dev/random/fortuna.c src/sys/dev/random/fortuna.h
- Improve messy union to just uint128_t.
- Remove unneeded 'static struct fortuna_start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
* src/sys/dev/random/yarrow.c src/sys/dev/random/yarrow.h
- Improve messy union to just uint128_t.
- Remove unneeded 'staic struct start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
- Fix some magic numbers elsewhere used as FAST and SLOW.
Differential Revision: https://reviews.freebsd.org/D2025
Reviewed by: vsevolod,delphij,rwatson,trasz,jmg
Approved by: so (delphij)
vtnet interfaces are always in promiscuous mode (at least if the
VIRTIO_NET_F_CTRL_RX feature is not negotiated with the host). if_promisc() on
a vtnet interface returned ENOTSUP although it has IFF_PROMISC set. This
confused the bridge code. Instead we now accept all enable/disable promiscuous
commands (and always keep IFF_PROMISC set).
There are also two issues with the if_bridge error handling.
If if_promisc() fails it uses bridge_delete_member() to clean up. This tries to
disable promiscuous mode on the interface. That runs into an assert, because
promiscuous mode was never set in the first place. (That's the panic reported in
PR 200210.)
We can only unset promiscuous mode if the interface actually is promiscuous.
This goes against the reference counting done by if_promisc(), but only the
first/last if_promic() calls can actually fail, so this is safe.
A second issue is a double free of bif. It's already freed by
bridge_delete_member().
PR: 200210
Differential Revision: https://reviews.freebsd.org/D2804
Reviewed by: philip (mentor)
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
gif(4) interface. Add new option "ignore_source" for gif(4) interface.
When it is enabled, gif's encapcheck function requires match only for
packet's destination address.
Differential Revision: https://reviews.freebsd.org/D2004
Obtained from: Yandex LLC
MFC after: 2 weeks
Sponsored by: Yandex LLC
packets on tunnel interfaces. Add support of these ioctls to gre(4),
gif(4) and me(4) interfaces. For incoming packets M_SETFIB() should use
if_fib value from ifnet structure, use proper value in gre(4) and me(4).
Differential Revision: https://reviews.freebsd.org/D2462
No objection from: #network
MFC after: 2 weeks
Sponsored by: Yandex LLC
since types became a enum C type. Some software uses such ifdefs to
determine whether an operating systems supports certain interface type.
Of course, such check is bogus. E.g. FreeBSD defines about 250 interface
types, but supports only around 20.
However, we need not upset such software so provide a set of defines. The
current set was taken to suffice the dhcpd.
Reported & tested by: Guy Yur <guyyur gmail.com>
to specify exact number of cpus in loader.conf which get annoying when you have
mix of machines which don't have equal number of total cpus. I propose "-1" as
that value. When loader.conf has net.isr.maxthreads = -1, netisr will use all
available cpus.
In collaboration with: davide
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2318
MFC after: 2 weeks
Sponsored by: Limelight Networks
quite unexpected result of toggling capabilities on the neighbour vlan(4)
interfaces.
Reviewed by: melifaro, np
Differential Revision: https://reviews.freebsd.org/D2310
Sponsored by: Nginx, Inc.
It is not network-specific code and would
be better as part of libkern instead.
Move zlib.h and zutil.h from net/ to sys/
Update includes to use sys/zlib.h and sys/zutil.h instead of net/
Submitted by: Steve Kiernan stevek@juniper.net
Obtained from: Juniper Networks, Inc.
GitHub Pull Request: https://github.com/freebsd/freebsd/pull/28
Relnotes: yes
A couple of fields are still exposed via struct bpf_if_ext so that
bpf_peers_present() can be inlined into its callers. However, this change
eliminates some type duplication in the resulting CTF container, since
otherwise ctfmerge(1) propagates the duplication through all types that
contain a struct bpf_if.
Differential Revision: https://reviews.freebsd.org/D2319
Reviewed by: melifaro, rpaulo
dhclient opens bpf as write-only to send packets. It never reads received
packets from that descriptor, but processing them in kernel takes time.
Especially much time takes packet timestamping on systems with expensive
timecounter, such as bhyve guest, where network speed dropped in half.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
discontinued by its initial authors. In FreeBSD the code was already
slightly edited during the pf(4) SMP project. It is about to be edited
more in the projects/ifnet. Moving out of contrib also allows to remove
several hacks to the make glue.
Reviewed by: net@
device polling rather than having it only be controlled by the compile
time option.
Summary: Rubicon Communications (Netgate)
Reviewers: #network, hiren
Reviewed By: #network, hiren
Subscribers: hiren
Differential Revision: https://reviews.freebsd.org/D2258
- Extend the number of available subtypes for Ethernet media by using some
of the ifmedia word's option bits to help denote subtypes. As a result, the
number of possible Ethernet subtype values increases from 31 to 511.
- Use some of those new values to define new media types.
- lacp_compose_key() recgonizes the new Ethernet media types added.
(Change made as required by a comment in if_media.h)
- New ioctl, SIOGIFXMEDIA, to handle getting the new extended media types.
SIOCGIFMEDIA is retained for backwards compatibility.
- Changes to ifconfig to allow it to handle the new extended media types.
Submitted by: mike@karels.net (original), hselasky
Reviewed by: jfvogel, gnn, hselasky
Approved by: jfvogel (mentor), gnn (mentor)
Differential Revision: http://reviews.freebsd.org/D1965
where counter was incremented on parent, instead of vlan(4) interface.
The second is more complicated. Historically, in our stack the incoming
packets are accounted in drivers, while incoming bytes for Ethernet
drivers are accounted in ether_input_internal(). Thus, it should be
removed from vlan(4) driver.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
- Use ifunit() instead of going through the interface list ourselves.
- Remove unused parameter.
- Move the most important comment above the function.
Sponsored by: Nginx, Inc.
initialization, when no input method specified before if_attach().
This prevents panics when if_input() method called directly e.g.
from bpf(4) code.
PR: 192426
Reviewed by: glebius
MFC after: 1 week
drivers can use it. This avoids some code duplication. Add missing
default case to all switch statements while at it. Also move the
hashing of the IPv6 flow field to layer 4 because the IPv6 flow field
is constant on a per L4 connection basis and not on a per L3 network.
Differential Revision: https://reviews.freebsd.org/D1987
Sponsored by: Mellanox Technologies
MFC after: 1 month
in kern_gzio.c. The old gzio interface was somewhat inflexible and has not
worked properly since r272535: currently, the gzio functions are called with
a range lock held on the output vnode, but kern_gzio.c does not pass the
IO_RANGELOCKED flag to vn_rdwr() calls, resulting in deadlock when vn_rdwr()
attempts to reacquire the range lock. Moreover, the new gzio interface can
be used to implement kernel core compression.
This change also modifies the kernel configuration options needed to enable
userland core dump compression support: gzio is now an option rather than a
device, and the COMPRESS_USER_CORES option is removed. Core dump compression
is enabled using the kern.compress_user_cores sysctl/tunable.
Differential Revision: https://reviews.freebsd.org/D1832
Reviewed by: rpaulo
Discussed with: kib
if_vmove().
In if_vmove(), if_detach_internal() and if_attach_internal() were
called in series to detach and reattach the interface. When
detaching, if_delgroup() was called and the interface leaves all of
the group membership. And then upon attachment, if_addgroup(ifp,
IFG_ALL) was called and it joined only "all" group again.
This had a problem. Normally, a cloned interface automatically joins
a group whose name is ifc_name of the cloner in addition to "all"
upon creation. However, if_vmove() removed the membership and did
not restore upon attachment.
Differential Revision: https://reviews.freebsd.org/D1859
allows adding an vlan interface into a bridge.
Thanks for William Katsak <wkatsak cs rutgers edu> for testing and fixing
an issue in my previous patch draft.
MFC after: 2 weeks
There was a race that bridge_ifdetach() could be called via
ifnet_departure event handler after vnet_bridge_uninit().
PR: 195859
Reported by: Danilo Egea Gondolfo
I edited the original change to retain the use of arc4random() as a seed for
the hashing as a very basic defense against intentional lagg port selection.
The author's original commit message (edited slightly):
sys/net/ieee8023ad_lacp.c
sys/net/if_lagg.c
In lagg_hashmbuf, use the FNV hash instead of the old
hash32_buf. The hash32 family of functions operate one octet
at a time, and when run on a string s of length n, their output
is equivalent to :
----- i=n-1
\
n \ (n-i-1) 32
( seed^ + / 33^ * s[i] ) % 2^
/
----- i=0
The problem is that the last five bytes of input don't get
multiplied by sufficiently many powers of 33 to rollover 2^32.
That means that changing the last few bytes (but obviously not
the very last) of input will always change the value of the
hash by a multiple of 33. In the case of lagg_hashmbuf() with
ipv4 input, the last four bytes are the TCP or UDP port
numbers. Since the output of lagg_hashmbuf is always taken
modulo the port count, and 3 is a common port count for a lagg,
that's bad. It means that the UDP or TCP source port will
never affect which lagg member is selected on a 3-port lagg.
At 10Gbps, I was not able to measure any difference in CPU
consumption between the old and new hash.
Submitted by: asomers (original commit)
Reviewed by: emaste, glebius
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1001723 on 2013/08/28 (original)
1114258 on 2015/01/22 (edit)
very questionable, since it makes vimages more dependent on each other. But
the reason for the backout is that it screwed up shutting down the pf purge
threads, and now kernel immedially panics on pf module unload. Although module
unloading isn't an advertised feature of pf, it is very important for
development process.
I'd like to not backout r276746, since in general it is good. But since it
has introduced numerous build breakages, that later were addressed in
r276841, r276756, r276747, I need to back it out as well. Better replay it
in clean fashion from scratch.
bits.
The motivation here is to eventually teach netisr and potentially
other networking subsystems a bit more about how RSS work queues / buckets
are configured so things have a hope of auto-configuring in the future.
* net/rss_config.[ch] takes care of the generic bits for doing
configuration, hash function selection, etc;
* topelitz.[ch] is now in net/ rather than netinet/;
* (and would be in libkern if it didn't directly include RSS_KEYSIZE;
that's a later thing to fix up.)
* netinet/in_rss.[ch] now just contains the IPv4 specific methods;
* and netinet/in6_rss.[ch] now just contains the IPv6 specific methods.
This should have no functional impact on anyone currently using
the RSS support.
Differential Revision: D1383
Reviewed by: gnn, jfv (intel driver bits)
Quoting 19 years bpf.4 manual from bpf-1.2a1:
"
(SIOCGIFADDR is obsolete under BSD systems. SIOCGIFCONF should be
used to query link-level addresses.)
"
* SIOCGIFADDR was not imported in NetBSD (bpf.c 1.36) and OpenBSD.
* Last bits (e.g. manpage claiming SIOCGIFADDR exists) was cleaned
from NetBSD via kern/21513 5 years ago,
from OpenBSD via documentation/6352 5 years ago.
r273087. Move all checks from gif_output() into gif_transmit(). Previously
they were checked always, because if_start always called gif_output.
Now gif_transmit() can be called directly from if_bridge() code and we need
do checks here.
PR: 196646
MFC after: 1 week
handle it in arc_output() instead of nd6_storelladdr().
* Remove IFT_ARCNET check from arpresolve() since arc_output() does not
use arpresolve() to handle broadcast/multicast. This check was there
since r84931. It looks like it was not used since r89099 (initial
import of Arcnet support where multicast is handled separately).
* Remove IFT_IEEE1394 case from nd6_storelladdr() since firewire_output()
calles nd6_storelladdr() for unicast addresses only.
* Remove IFT_ARCNET case from nd6_storelladdr() since arc_output() now
handles multicast by itself.
As a result, we have the following pattern: all non-ethernet-style
media have their own multicast map handling inside their appropriate
routines. On the other hand, arpresolve() (and nd6_storelladdr()) which
meant to be 'generic' ones de-facto handles ethernet-only multicast maps.
MFC after: 3 weeks
Split functions that initialize various pf parts into their
vimage parts and global parts.
Since global parts appeared to be only mutex initializations, just
abandon them and use MTX_SYSINIT() instead.
Kill my incorrect VNET_FOREACH() iterator and instead use correct
approach with VNET_SYSINIT().
PR: 194515
Differential Revision: D1309
Submitted by: glebius, Nikos Vassiliadis <nvass@gmx.com>
Reviewed by: trociny, zec, gnn
* Make most of lltable_* methods 'normal' functions instead of inline
* Add lltable_get_<af|ifp>() functions to access given lltable fields
* Temporarily resurrect nd6_lookup() function
use llt_fill_sa_entry() llt method to store lle address in sa.
* Eliminate L3_ADDR macro and either reference IPv4/IPv6 address
directly from lle or use newly-created llt_fill_sa_entry().
* Do not store sockaddr inside arp/ndp lle anymore.
and explicit calls to RTENTRY_FREE_LOCKED()
* Use lltable_prefix_free() in arp_ifscrub to be consistent with nd6.
* Rename <lltable_|llt>_delete function to _delete_addr() to note that
this function is used to external callers. Make this function maintain
its own locking.
* Use lookup/unlink/clear call chain from internal callers instead of
delete_addr.
* Fix LLE_DELETED flag handling
cleanup including unlinking/freeing
* Relax locking in lltable_prefix_free_af/lltable_free
* Do not pass @llt to lle free callback: it is always NULL now.
* Unify arptimer/nd6_llinfo_timer: explicitly unlock lle avoiding
unlock/lock sequinces
* Do not pass unlocked lle to nd6_ns_output(): add nd6_llinfo_get_holdsrc()
to retrieve preferred source address from lle hold queue and pass it
instead of lle.
* Finally, make nd6_create() create and return unlocked lle
* Separate defrtr handling code from nd6_free():
use nd6_check_del_defrtr() to check if we need to keep entry instead of
performing GC,
use nd6_check_recalc_defrtr() to perform actual recalc on lle removal.
* Move isRouter handling from nd6_cache_lladdr() to separate
nd6_check_router()
* Add initial code to maintain lle runtime flags in sync.
from the FreeBSD network code. The flag is still kept around in the
"sys/mbuf.h" header file, but does no longer have any users. Instead
the "m_pkthdr.rsstype" field in the mbuf structure is now used to
decide the meaning of the "m_pkthdr.flowid" field. To modify the
"m_pkthdr.rsstype" field please use the existing "M_HASHTYPE_XXX"
macros as defined in the "sys/mbuf.h" header file.
This patch introduces new behaviour in the transmit direction.
Previously network drivers checked if "M_FLOWID" was set in "m_flags"
before using the "m_pkthdr.flowid" field. This check has now now been
replaced by checking if "M_HASHTYPE_GET(m)" is different from
"M_HASHTYPE_NONE". In the future more hashtypes will be added, for
example hashtypes for hardware dedicated flows.
"M_HASHTYPE_OPAQUE" indicates that the "m_pkthdr.flowid" value is
valid and has no particular type. This change removes the need for an
"if" statement in TCP transmit code checking for the presence of a
valid flowid value. The "if" statement mentioned above is now a direct
variable assignment which is then later checked by the respective
network drivers like before.
Additional notes:
- The SCTP code changes will be committed as a separate patch.
- Removal of the "M_FLOWID" flag will also be done separately.
- The FreeBSD version has been bumped.
MFC after: 1 month
Sponsored by: Mellanox Technologies
use rwlock accessible via external functions
(IF_AFDATA_CFG_* -> if_afdata_cfg_*()) for all control plane tasks
use rmlock (IF_AFDATA_RUN_*) for fast-path lookups.
Update route MTU in case of ifnet MTU change.
Add new RTF_FIXEDMTU to track explicitly specified MTU.
Old behavior:
ifconfig em0 mtu 1500->9000 -> all routes traversing em0 do not change MTU.
User has to manually update all routes.
ifconfig em0 mtu 9000->1500 -> all routes traversing em0 do not change MTU.
However, if ip[6]_output finds route with rt_mtu > interface mtu, rt_mtu
gets updated.
New behavior:
ifconfig em0 mtu 1500->9000 -> all interface routes in all fibs gets updated
with new MTU unless RTF_FIXEDMTU flag set on them.
ifconfig em0 mtu 9000->1500 -> all routes in all fibs gets updated with new
MTU unless RTF_FIXEDMTU flag set on them AND rt_mtu is less than ifp mtu.
route add ... -mtu XXX automatically sets RTF_FIXEDMTU flag.
route change .. -mtu 0 automatically removes RTF_FIXEDMTU flag.
PR: 194238
MFC after: 1 month
CR: D1125
* struct llentry is now basically split into 2 pieces:
all fields within 64 bytes (amd64) are now protected by both
ifdata lock AND lle lock, e.g. you require both locks to be held
exclusively for modification. All data necessary for fast path
operations is kept here. Some fields were added:
- r_l3addr - makes lookup key liev within first 64 bytes.
- r_flags - flags, containing pre-compiled decision whether given
lle contains usable data or not. Current the only flag is RLLE_VALID.
- r_len - prepend data len, currently unused
- r_kick - used to provide feedback to control plane (see below).
All other fields are protected by lle lock.
* Add simple state machine for ARP to handle "about to expire" case:
Current model (for the fast path) is the following:
- rlock afdata
- find / rlock rte
- runlock afdata
- see if "expire time" is approaching
(time_uptime + la->la_preempt > la->la_expire)
- if true, call arprequest() and decrease la_preempt
- store MAC and runlock rte
New model (data plane):
- rlock afdata
- find rte
- check if it can be used using r_* fields only
- if true, store MAC
- if r_kick field != 0 set it to 0.
- runlock afdata
New mode (control plane):
- schedule arptimer to be called in (V_arpt_keep - V_arp_maxtries)
seconds instead of V_arpt_keep.
- on first timer invocation change state from ARP_LLINFO_REACHABLE
to ARP_LLINFO_VERIFY, sets r_kick to 1 and shedules next call in
V_arpt_rexmit (default to 1 sec).
- on subsequent timer invocations in ARP_LLINFO_VERIFY state, checks
for r_kick value: reschedule if not changed, and send arprequest()
if set to zero (e.g. entry was used).
* Convert IPv4 path to use new single-lock approach. IPv6 bits to follow.
* Slow down in_arpinput(): now valid reply will (in most cases) require
acquiring afdata WLOCK twice. This is requirement for storing changed
lle data. This change will be slightly optimized in future.
* Provide explicit hash link/unlink functions for both ipv4/ipv6 code.
This will probably be moved to generic lle code once we have per-AF
hashing callback inside lltable.
* Perform lle unlink on deletion immediately instead of delaying it to
the timer routine.
* Make r244183 more explicit: use new LLE_CALLOUTREF flag to indicate the
presence of lle reference used for safe callout calls.
lla_lookup(LLE_CREATE) -> lla_create
lla_lookup(LLE_DELETE) -> lla_delete
Assume lla_create to return LLE_EXCLUSIVE lock for lle.
* Rework lla_rt_output to perform all lle changes under afdata WLOCK.
* change arp_ifscrub() ackquire afdata WLOCK, the same as arp_ifinit().
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
gcc requires variables to be initialised in two places. One of them
is correctly used only under the same conditional though.
For module builds properly check if the kernel supports INET or INET6,
as otherwise various mips kernels without IPv6 support would fail to build.
Split it into two modules: if_gre(4) for GRE encapsulation and
if_me(4) for minimal encapsulation within IP.
gre(4) changes:
* convert to if_transmit;
* rework locking: protect access to softc with rmlock,
protect from concurrent ioctls with sx lock;
* correct interface accounting for outgoing datagramms (count only payload size);
* implement generic support for using IPv6 as delivery header;
* make implementation conform to the RFC 2784 and partially to RFC 2890;
* add support for GRE checksums - calculate for outgoing datagramms and check
for inconming datagramms;
* add support for sending sequence number in GRE header;
* remove support of cached routes. This fixes problem, when gre(4) doesn't
work at system startup. But this also removes support for having tunnels with
the same addresses for inner and outer header.
* deprecate support for various GREXXX ioctls, that doesn't used in FreeBSD.
Use our standard ioctls for tunnels.
me(4):
* implementation conform to RFC 2004;
* use if_transmit;
* use the same locking model as gre(4);
PR: 164475
Differential Revision: D1023
No objections from: net@
Relnotes: yes
Sponsored by: Yandex LLC
it, except Ethernet, where it carried ng_ether(4) pointer.
For now carry the pointer in if_l2com directly.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Some virtual if drivers has (ab)used ifa ifa_rtrequest hook to enforce
route MTU to be not bigger that interface MTU. While ifa_rtrequest hooking
might be an option in some situation, it is not feasible to do MTU checks
there: generic (or per-domain) routing code is perfectly capable of doing
this.
We currrently have 3 places where MTU is altered:
1) route addition.
In this case domain overrides radix _addroute callback (in[6]_addroute)
and all necessary checks/fixes are/can be done there.
2) route change (especially, GW change).
In this case, there are no explicit per-domain calls, but one can
override rte by setting ifa_rtrequest hook to domain handler
(inet6 does this).
3) ifconfig ifaceX mtu YYYY
In this case, we have no callbacks, but ip[6]_output performes runtime
checks and decreases rt_mtu if necessary.
Generally, the goals are to be able to handle all MTU changes in
control plane, not in runtime part, and properly deal with increased
interface MTU.
This commit changes the following:
* removes hooks setting MTU from drivers side
* adds proper per-doman MTU checks for case 1)
* adds generic MTU check for case 2)
* The latter is done by using new dom_ifmtu callback since
if_mtu denotes L3 interface MTU, e.g. maximum trasmitted _packet_ size.
However, IPv6 mtu might be different from if_mtu one (e.g. default 1280)
for some cases, so we need an abstract way to know maximum MTU size
for given interface and domain.
* moves rt_setmetrics() before MTU/ifa_rtrequest hooks since it copies
user-supplied data which must be checked.
* removes RT_LOCK_ASSERT() from other ifa_rtrequest hooks to be able to
use this functions on new non-inserted rte.
More changes will follow soon.
MFC after: 1 month
Sponsored by: Yandex LLC
* Remove &ifpp from ip6_output() in favor of ri->ri_nh_info
* Provide different wrappers to in6_selectsrc:
Currently it is used by 2 differenct type of customers:
- socket-based one, which all are unsure about provided
address scope and
- in-kernel ones (ND code mostly), which don't have
any sockets, options, crededentials, etc.
So, we provide two different wrappers to in6_selectsrc()
returning select source.
* Make different versions of selectroute():
Currenly selectroute() is used in two scenarios:
- SAS, via in6_selecsrc() -> in6_selectif() -> selectroute()
- output, via in6_output -> wrapper -> selectroute()
Provide different versions for each customer:
- fib6_lookup_nh_basic()-based in6_selectif() which is
capable of returning interface only, without MTU/NHOP/L2
calculations
- full-blown fib6_selectroute() with cached route/multipath/
MTU/L2
* Stop using routing table for link-local address lookups
* Add in6_ifawithifp_lla() to make for-us check faster for link-local
* Add in6_splitscope / in6_setllascope for faster embed/deembed scopes
This code has had an extensive rewrite and a good series of reviews, both by the author and other parties. This means a lot of code has been simplified. Pluggable structures for high-rate entropy generators are available, and it is most definitely not the case that /dev/random can be driven by only a hardware souce any more. This has been designed out of the device. Hardware sources are stirred into the CSPRNG (Yarrow, Fortuna) like any other entropy source. Pluggable modules may be written by third parties for additional sources.
The harvesting structures and consequently the locking have been simplified. Entropy harvesting is done in a more general way (the documentation for this will follow). There is some GREAT entropy to be had in the UMA allocator, but it is disabled for now as messing with that is likely to annoy many people.
The venerable (but effective) Yarrow algorithm, which is no longer supported by its authors now has an alternative, Fortuna. For now, Yarrow is retained as the default algorithm, but this may be changed using a kernel option. It is intended to make Fortuna the default algorithm for 11.0. Interested parties are encouraged to read ISBN 978-0-470-47424-2 "Cryptography Engineering" By Ferguson, Schneier and Kohno for Fortuna's gory details. Heck, read it anyway.
Many thanks to Arthur Mesh who did early grunt work, and who got caught in the crossfire rather more than he deserved to.
My thanks also to folks who helped me thresh this out on whiteboards and in the odd "Hallway track", or otherwise.
My Nomex pants are on. Let the feedback commence!
Reviewed by: trasz,des(partial),imp(partial?),rwatson(partial?)
Approved by: so(des)
directly accessed. Although this will work on some platforms, it can
throw an exception if the pointer is invalid and then panic the kernel.
Add a missing SYSCTL_IN() of "SCTP_BASE_STATS" structure.
MFC after: 3 days
Sponsored by: Mellanox Technologies
* Use NHF_ namespace for all nhop flags
* Rename nhop_data -> nhop_prepend
* Rename fib4_lookup_nh_extended -> fib4_lookup_nh_ext
* Add "flags" argument to fib4_lookup_nh_ext() to specify whether we want
returned nh_ext structure to be refcounted or not.
structure without doinf L2 resolve. It also requires freeing
references by calling fib4_free_nh_ext().
Convert in_pcbladdr() to use it.
Convert tcp_maxmtu() to use it.
vxlan creates a virtual LAN by encapsulating the inner Ethernet frame in
a UDP packet. This implementation is based on RFC7348.
Currently, the IPv6 support is not fully compliant with the specification:
we should be able to receive UPDv6 packets with a zero checksum, but we
need to support RFC6935 first. Patches for this should come soon.
Encapsulation protocols such as vxlan emphasize the need for the FreeBSD
network stack to support batching, GRO, and GSO. Each frame has to make
two trips through the network stack, and each frame will be at most MTU
sized. Performance suffers accordingly.
Some latest generation NICs have begun to support vxlan HW offloads that
we should also take advantage of. VIMAGE support should also be added soon.
Differential Revision: https://reviews.freebsd.org/D384
Reviewed by: gnn
Relnotes: yes
The goals of the new API is to provide consumers with minimal
needed information, but as fast as possible. So we provide
full nexthop info copied into alighed on-cache structure
instead of rte/ia pointers, their refcounts and locks.
This does not provide solution for protecting from egress
ifp destruction, but does not make it any worse.
Current changes:
nhops:
Add fib4_lookup_prepend() function which stores either full
L2+L3 prepend info (e.g. MAC header in case of plain IPv4) or
L3 info with NH_FLAGS_L2_INCOMPLETE flag indicating that no valid L2
info exists and we have to take "slow" path.
ip_output:
Currently ip[ 46]_output consumers use 'struct route' for
the following purposes:
1) double lookup avoidance(route caching)
2) plain route caching
3) get path MTU to be able to notify source.
The former pattern is mostly used by various tunnels
(gif, gre, stf). (Actually, gre is the only remaining,
others were already converted. Their locking model did
not scale good enogh to benefit from such caching, so
we have (temporarily) removed it without any performance
loss).
Plain route caching used by SCTP is simply wrong and should be removed.
Temporary break it for now just to be able to compile.
Optimize path mtu reporting by providing it in new 'route_info' stucture.
Minimize games with @ia locking/refcounting for route lookup:
add special nhop[46]_extended structure to store more route attributes.
Pointer to given structure can be passed to fib4_lookup_prepend() to indicate
we want this info (we actually needs it for UDP and raw IP).
ether_output:
Provide light-weight ether_output2() call to deal with
transmitting L2 frame (e.g. properly handle broadcast/simloop/bridge/
other L2 hooks before actually transmitting frame by if_transmit()).
Add a hack based on new RT_NHOP ro_flag to distinguish which version should
we call. Better way is probably to add a new "if_output_frame" driver
callbacks.
Next steps:
* Convert ip_fastfwd part
* Implement auto-growing array for per-radix nexthops
* Implement LLE tracking for nexthop calculations to be able to
immediately provide all necessary info in single route lookup
for gateway routes
* Switch radix locking scheme to runtime/cfg lock
* Implement multipath support for rtsock
* Implement "tracked nexthops" for tunnels (e.g. _proper_
nexthop caching)
* Add IPv6 support for remaining parts (postponed not to
interfere with user/ae/inet6 branch)
* Consider adding "if_output_frame" driver call to
ease logical frame pushing.
o convert to if_transmit;
o use rmlock to protect access to gif_softc;
o use sx lock to protect from concurrent ioctls;
o remove a lot of unneeded and duplicated code;
o remove cached route support (it won't work with concurrent io);
o style fixes.
Reviewed by: melifaro
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
is added to return EEXIST when only "b" interface exists---this can happen
when epair<N>b is moved to a vnet jail and then "ifconfig epair<N> create"
is invoked there.
outer header, consider it as new packet and clear the protocols flags.
This fixes problems when IPSEC traffic goes through various tunnels and router
doesn't send ICMP/ICMPv6 errors.
PR: 174602
Obtained from: Yandex LLC
MFC after: 2 weeks
Sponsored by: Yandex LLC
LOR of softc rmlock in iflladdr_event handlers.
- Call if_delmulti_ifma() after LACP_UNLOCK(). This fixes another LOR.
- Fix a panic in lacp_transit_expire().
- Fix a panic in lagg_input() upon shutting down a port.
if_lagg(4) interfaces which were cloned in a vnet jail.
Sysctl nodes which are dynamically generated for each cloned interface
(net.link.lagg.N.*) have been removed, and use_flowid and flowid_shift
ifconfig(8) parameters have been added instead. Flags and per-interface
statistics counters are displayed in "ifconfig -v".
CR: D842
This is temporary commit to be merged to 10.
Other approach (like hash table) should be used
to store different masks.
PR: 194078
Submitted by: Rumen Telbizov
MFC after: 3 days
This seems to allow us to pass a universe with either clang or gcc
after r272244 (and r272260) and probably makes it easier to untabgle
these chained #includes in the future.
if_var.h has the expected on and if_var.h include ifq.h and thus we get
duplicates. It seems only one cavium ethernet file actually includes ifq.h
directly which might be another cleanup to be done but need to test first.
then drop lock, run the attach routines, and then set it to specific
proto. This removes tons of WITNESS warnings.
- Make lagg protocol attach handlers not failing and allocate memory
with M_WAITOK.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
Reviewed by: adrian, rmacklem
Sponsored by: Mellanox Technologies
MFC after: 1 week
struct ifnet if_oqdrops.
Some netgraph modules used ifqueue w/o ifnet. Accounting of queue drops
is simply removed from them. There were no API to read this statistic.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
imporant moments that we discussed with Marcel and Anuranjan was that
a converted driver should return false for 'grep ifnet if_driver.c' :)
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The compat counters will go away, but the function will remain in its place,
and in all places where it is going to be called.
Discussed with: melifaro
and receives frames on any port of the lagg(4).
Phabric: D549
Reviewed by: glebius, thompsa
Approved by: glebius
Obtained from: OpenBSD
Sponsored by: QNAP Systems Inc.
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ifa_ifwithdstaddr. For the sake of backwards compatibility, the new
arguments were added to new functions named ifa_ifwithnet_fib and
ifa_ifwithdstaddr_fib, while the old functions became wrappers around the
new ones that passed RT_ALL_FIBS for the fib argument. However, the
backwards compatibility is not desired for FreeBSD 11, because there are
numerous other incompatible changes to the ifnet(9) API. We therefore
decided to remove it from head but leave it in place for stable/9 and
stable/10. In addition, this commit adds the fib argument to
ifa_ifwithbroadaddr for consistency's sake.
sys/sys/param.h
Increment __FreeBSD_version
sys/net/if.c
sys/net/if_var.h
sys/net/route.c
Add fibnum argument to ifa_ifwithbroadaddr, and remove the _fib
versions of ifa_ifwithdstaddr, ifa_ifwithnet, and ifa_ifwithroute.
sys/net/route.c
sys/net/rtsock.c
sys/netinet/in_pcb.c
sys/netinet/ip_options.c
sys/netinet/ip_output.c
sys/netinet6/nd6.c
Fixup calls of modified functions.
share/man/man9/ifnet.9
Document changed API.
CR: https://reviews.freebsd.org/D458
MFC after: Never
Sponsored by: Spectra Logic
with no RSS hash.
When doing RSS:
* Create a new IPv4 netisr which expects the frames to have been verified;
it just directly dispatches to the IPv4 input path.
* Once IPv4 reassembly is done, re-calculate the RSS hash with the new
IP and L3 header; then reinject it as appropriate.
* Update the IPv4 netisr to be a CPU affinity netisr with the RSS hash
function (rss_soft_m2cpuid) - this will do a software hash if the
hardware doesn't provide one.
NICs that don't implement hardware RSS hashing will now benefit from RSS
distribution - it'll inject into the correct destination netisr.
Note: the netisr distribution doesn't work out of the box - netisr doesn't
query RSS for how many CPUs and the affinity setup. Yes, netisr likely
shouldn't really be doing CPU stuff anymore and should be "some kind of
'thing' that is a workqueue that may or may not have any CPU affinity";
that's for a later commit.
Differential Revision: https://reviews.freebsd.org/D527
Reviewed by: grehan
and keep both converted to drvapi and non-converted drivers
compilable.
o Make if_t typedef to struct ifnet *.
o Remove shim functions.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
for route(4) socket and ifmib(4) sysctl.
o Move fields from if_data to ifnet, but keep all statistic counters
separate, since they should disappear later.
o Provide function if_data_copy() to fill if_data, utilize it in routing
socket and ifmib handler.
o Provide overridable ifnet(9) method to fetch counters. If no provided,
if_get_counters_compat() would be used, that returns old counters.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
via net.link.generic.IFMIB_IFDATA.*.IFDATA_GENERAL sysctl. Reasons
for removal are:
- No code in tree uses this possibility.
- The documentation ifmib(4) doesn't say that such possibility
exist. The example provided in manual page only reads data.
- On many interfaces the feature simply doesn't work, since they
do accounting in hardware, and overwrite if_data on tick.
Sponsored by: Nginx, Inc.
* Convert ixgbe to use this ioctl
* Convert ifconfig to use generic i2c handler for "ix" interfaces.
Approved by: Eric Joyner (ixgbe part)
MFC after: 2 weeks
Sponsored by: Yandex LLC
QSFP+ data via i2c inteface. These constants has been taken
from SFF-8436 "QSFP+ 10 Gbs 4X PLUGGABLE TRANSCEIVER" standard
rev 4.8.
* Add support for printing QSFP+ information from 40G NICs
such as Chelsio T5.
This commit does not contain ioctl changes necessary for this
functionality work, there will be another commit soon.
Example:
cxl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=ec07bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,.....>
ether 00:07:43:28:ad:08
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet 40Gbase-LR4 <full-duplex>
status: active
plugged: QSFP+ 40GBASE-LR4 (MPO Parallel Optic)
vendor: OEM PN: OP-QSFP-40G-LR4 SN: 20140318001 DATE: 2014-03-18
module temperature: 64.06 C voltage: 3.26 Volts
lane 1: RX: 0.47 mW (-3.21 dBm) TX: 2.78 mW (4.46 dBm)
lane 2: RX: 0.20 mW (-6.94 dBm) TX: 2.80 mW (4.47 dBm)
lane 3: RX: 0.18 mW (-7.38 dBm) TX: 2.79 mW (4.47 dBm)
lane 4: RX: 0.90 mW (-0.45 dBm) TX: 2.80 mW (4.48 dBm)
Tested on: Chelsio T5
Tested on: Mellanox/Huawei passive/active cables/transceivers.
MFC after: 2 weeks
Sponsored by: Yandex LLC
Mostly bugfixes or features developed in the past 6 months,
so this is a 10.1 candidate.
Basically no user API changes (some bugfixes in sys/net/netmap_user.h).
In detail:
1. netmap support for virtio-net, including in netmap mode.
Under bhyve and with a netmap backend [2] we reach over 1Mpps
with standard APIs (e.g. libpcap), and 5-8 Mpps in netmap mode.
2. (kernel) add support for multiple memory allocators, so we can
better partition physical and virtual interfaces giving access
to separate users. The most visible effect is one additional
argument to the various kernel functions to compute buffer
addresses. All netmap-supported drivers are affected, but changes
are mechanical and trivial
3. (kernel) simplify the prototype for *txsync() and *rxsync()
driver methods. All netmap drivers affected, changes mostly mechanical.
4. add support for netmap-monitor ports. Think of it as a mirroring
port on a physical switch: a netmap monitor port replicates traffic
present on the main port. Restrictions apply. Drive carefully.
5. if_lem.c: support for various paravirtualization features,
experimental and disabled by default.
Most of these are described in our ANCS'13 paper [1].
Paravirtualized support in netmap mode is new, and beats the
numbers in the paper by a large factor (under qemu-kvm,
we measured gues-host throughput up to 10-12 Mpps).
A lot of refactoring and additional documentation in the files
in sys/dev/netmap, but apart from #2 and #3 above, almost nothing
of this stuff is visible to other kernel parts.
Example programs in tools/tools/netmap have been updated with bugfixes
and to support more of the existing features.
This is meant to go into 10.1 so we plan an MFC before the Aug.22 deadline.
A lot of this code has been contributed by my colleagues at UNIPI,
including Giuseppe Lettieri, Vincenzo Maffione, Stefano Garzarella.
MFC after: 3 days.
This is needed to prevent having interfaces with ifp->if_addr == NULL
on bridge interfaces. Moving the notification event handlers up makes
sure the interfaces are removed before doing any more cleanup.
Sponsored by: Citrix Systems R&D
Reviewed by: melifaro
Differential Revision: https://reviews.freebsd.org/D598
net/if.c
- Move interface removal notification up in if_detach_internal.
- Do not count global number of states and of src_nodes,
use uma_zone_get_cur() to obtain values.
- Struct pf_status becomes merely an ioctl API structure,
and moves to netpfil/pf/pf.h with its constants.
- V_pf_status is now of type struct pf_kstatus.
Submitted by: Kajetan Staszkiewicz <vegeta tuxpowered.net>
Sponsored by: InnoGames GmbH
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
Direct bpf(4) consumers should now work fine with this tunable turned on.
In fact, the only case when optimized_writers can change program
behavior is direct bpf(4) consumer setting its read filter to
catch-all one.
MFC after: 2 weeks
Sponsored by: Yandex LLC
- stdio.h is needed for fprint()
- make memsize uint32_t to avoid errors due to overflow
- honor the *XPOLL flagg in NIOCREGIF requests
- mmap fails wit MAP_FAILED, not NULL.
MFC after: 3 days
interface allows the ifnet structure to be defined as an opaque
type in NIC drivers. This then allows the ifnet structure to be
changed without a need to change or recompile NIC drivers.
Put differently, NIC drivers can be written and compiled once and
be used with different network stack implementations, provided of
course that those network stack implementations have an API and
ABI compatible interface.
This commit introduces the 'if_t' type to replace 'struct ifnet *'
as the type of a network interface. The 'if_t' type is defined as
'void *' to enable the compiler to perform type conversion to
'struct ifnet *' and vice versa where needed and without warnings.
The functions that implement the API are the only functions that
need to have an explicit cast.
The MII code has been converted to use the driver API to avoid
unnecessary code churn. Code churn comes from having to work with
both converted and unconverted drivers in correlation with having
callback functions that take an interface. By converting the MII
code first, the callback functions can be defined so that the
compiler will perform the typecasts automatically.
As soon as all drivers have been converted, the if_t type can be
redefined as needed and the API functions can be fix to not need
an explicit cast.
The immediate benefactors of this change are:
1. Juniper Networks - The network stack implementation in Junos
is entirely different from FreeBSD's one and this change
allows Juniper to build "stock" NIC drivers that can be used
in combination with both the FreeBSD and Junos stacks.
2. FreeBSD - This change opens the door towards changing ifnet
and implementing new features and optimizations in the network
stack without it requiring a change in the many NIC drivers
FreeBSD has.
Submitted by: Anuranjan Shukla <anshukla@juniper.net>
Reviewed by: glebius@
Obtained from: Juniper Networks, Inc.
ifa_ifwithnet() and ifa_ifwithdstaddr() The legacy functions will call the
_fib() versions with RT_ALL_FIBS, preserving legacy behavior.
sys/net/if_var.h
sys/net/if.c
Add legacy-compatible functions as described above. Ensure legacy
behavior when RT_ALL_FIBS is passed as fibnum.
sys/netinet/in_pcb.c
sys/netinet/ip_output.c
sys/netinet/ip_options.c
sys/net/route.c
sys/net/rtsock.c
sys/netinet6/nd6.c
Call with _fib() functions if we must use a specific fib, or the
legacy functions otherwise.
tests/sys/netinet/fibs_test.sh
tests/sys/netinet/udp_dontroute.c
Improve the udp_dontroute test. The bug that this test exercises is
that ifa_ifwithnet() will return the wrong address, if multiple
interfaces have addresses on the same subnet but with different
fibs. The previous version of the test only considered one possible
failure mode: that ifa_ifwithnet_fib() might fail to find any
suitable address at all. The new version also checks whether
ifa_ifwithnet_fib() finds the correct address by checking where the
ARP request goes.
Reported by: bz, hrs
Reviewed by: hrs
MFC after: 1 week
X-MFC-with: 264905
Sponsored by: Spectra Logic
birthday-paradox style address collisions when
bhyve VMs are connected to the same broadcoast
domain and are using pseudo-random allocations.
Reviewed by: gnn
MFC after: 1 week
Since radix has been ignoring sa_family in passed sockaddrs,
no one ever has bothered filling valid sa_family in netmasks.
Additionally, radix adjusts sa_len field in every netmask not to
compare zero bytes at all.
This leads us to rt_mask with sa_family of AF_UNSPEC (-1) and
arbitrary sa_len field (0 for default route, for example).
However, rtsock have been passing that rt_mask intact for ages,
requiring all rtsock consumers to make ther own local hacks.
We even have unfixed on in base:
do `route -n monitor` in one window and issue `route -n get addr`
for some directly-connected address. You will probably see the following:
got message of size 304 on Thu May 8 15:06:06 2014
RTM_GET: Report Metrics: len 304, pid: 30493, seq 1, errno 0, flags:<UP,DONE,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK,IFP,IFA>
10.0.0.0 link#1 (255) ffff ffff ff em0:8.0.27.c5.29.d4 10.0.0.92
_________________^^^^^^^^^^^^^^^^^^
after the change:
got message of size 312 on Thu May 8 15:44:07 2014
RTM_GET: Report Metrics: len 312, pid: 2895, seq 1, errno 0, flags:<UP,DONE,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK,IFP,IFA>
10.0.0.0 link#1 255.255.255.0 em0:8.0.27.c5.29.d4 10.0.0.92
_________________^^^^^^^^^^^^^^^^^^
Sponsored by: Yandex LLC
MFC after: 1 month
It looks like current consumers are either unaware
of MRT (and uses RT_DEFAULT_FIB implicitly) or
know what thay are doing, In latter case they
will be either hit by KASSERT or ESCRH will be returned
due to NULL rnh.
The thread that is destroying the lagg has already set sc->sc_psc=NULL when
the "ifconfig -am" thread gets to lacp_req(). It tries to dereference
sc->sc_psc and panics. The solution is for lacp_req() to check the value of
sc->sc_psc. If NULL, harmlessly return an lacp_opreq structure full of
zeros. Full details in GNATS.
PR: kern/189003
Reviewed by: timeout on freebsd-net@
MFC after: 3 weeks
Sponsored by: Spectra Logic Corporation
All rtsock-initiated rte creation/modification are now
performed in route.c holding radix tree write lock.
This reduces the need for per-rte mutex.
Sponsored by: Yandex LLC
MFC after: 1 month
* memory is now allocated as early as possible, without holding locks.
* sysctl users are now guaranteed to get a response (M_WAITOK buffer prealloc).
* socket users are more likely to use on-stack buffer for replies.
* standard kernel malloc/free functions are now used instead of radix wrappers.
rt_msg2() has been renamed to rtsock_msg_buffer().
MFC after: 1 month
RTM_CHANGE is now handled inside route.c:rtrequest1_fib() as it should be.
Note change change handler is a separate function rtrequest1_fib_change().
MFC after: 1 month
These two bugs are closely related. The root cause is that ifa_ifwithnet
does not consider FIBs when searching for an interface address.
sys/net/if_var.h
sys/net/if.c
Add a fib argument to ifa_ifwithnet and ifa_ifwithdstadddr. Those
functions will only return an address whose interface fib equals the
argument.
sys/net/route.c
Update calls to ifa_ifwithnet and ifa_ifwithdstaddr with fib
arguments.
sys/netinet/in.c
Update in_addprefix to consider the interface fib when adding
prefixes. This will prevent it from not adding a subnet route when
one already exists on a different fib.
sys/net/rtsock.c
sys/netinet/in_pcb.c
sys/netinet/ip_output.c
sys/netinet/ip_options.c
sys/netinet6/nd6.c
Add RT_DEFAULT_FIB arguments to ifa_ifwithdstaddr and ifa_ifwithnet.
In some cases it there wasn't a clear specific fib number to use.
In others, I was unable to test those functions so I chose
RT_DEFAULT_FIB to minimize divergence from current behavior. I will
fix some of the latter changes along with PR kern/187553.
tests/sys/netinet/fibs_test.sh
tests/sys/netinet/udp_dontroute.c
tests/sys/netinet/Makefile
Revert r263738. The udp_dontroute test was right all along.
However, bugs kern/187550 and kern/187553 cancelled each other out
when it came to this test. Because of kern/187553, ifa_ifwithnet
searched the default fib instead of the requested one, but because
of kern/187550, there was an applicable subnet route on the default
fib. The new test added in r263738 doesn't work right, however. I
can verify with dtrace that ifa_ifwithnet returned the wrong address
before I applied this commit, but route(8) miraculously found the
correct interface to use anyway. I don't know how.
Clear expected failure messages for kern/187550 and kern/187552.
PR: kern/187550
PR: kern/187552
Reviewed by: melifaro
MFC after: 3 weeks
Sponsored by: Spectra Logic
sys/net/route.c
In rtinit1, use the interface fib instead of the process fib. The
latter wasn't very useful because ifconfig(8) is usually invoked
with the default process fib. Changing ifconfig(8) to use setfib(2)
would be redundant, because it already sets the interface fib.
tests/sys/netinet/fibs_test.sh
Clear the expected ATF failure
sys/net/if.c
Pass the interface fib in calls to rtrequest1_fib and rtalloc1_fib
sys/netinet/in.c
sys/net/if_var.h
Add a fibnum argument to ifa_switch_loopback_route, a subroutine of
in_scrubprefix. Pass it the interface fib.
PR: kern/187549
Reviewed by: melifaro
MFC after: 3 weeks
Sponsored by: Spectra Logic Corporation
De-virtualize UMA zone pf_mtag_z and move to global initialization part.
The m_tag struct does not know about vnet context and the pf_mtag_free()
callback is called unaware of current vnet. This causes a panic.
MFC after: 1 week
network interfaces limited to 32 transmit segments, there
are two known issues.
The more serious one is that for an I/O of slightly less than 64K,
the net device driver prepends an ethernet header, resulting in a
TSO segment slightly larger than 64K. Since m_defrag() copies this
into 33 mbuf clusters, the transmit fails with EFBIG.
A tester indicated observing a similar failure using iSCSI.
The second less critical problem is that the network
device driver must copy the mbuf chain via m_defrag()
(m_collapse() is not sufficient), resulting in measurable overhead.
This patch reduces the default size of if_hw_tsomax
slightly, so that the first issue is avoided.
Fixing the second issue will require a way for the
network device driver to inform tcp_output() that it
is limited to 32 transmit segments.
Reported and tested by: csforgeron@gmail.com, markus.gebert@hostpoint.ch
MFC after: 2 weeks
was stacked on top of a network interface that set if_hw_tsomax,
tcp_output() would see the default value instead of the value
set by the network interface. This patch modifies vlan so that
it sets if_hw_tsomax to the value of the parent interface.
Reviewed by: glebius
MFC after: 2 weeks
was stacked on top of network interfaces that set if_hw_tsomax,
tcp_output() would see the default value instead of the value
set by the network interface(s). This patch modifies lagg so that
it sets if_hw_tsomax to the minimum of the value(s) for the
underlying network interfaces.
Reviewed by: glebius
MFC after: 2 weeks
This KASSERT() existed as a sanity check that upper layers in the network
stack (e.g. inet, inet6) had released their reference to the underlying
driver's multicast memberships (ifmultiaddr{}). However it assumes the
lifecycle of the driver membership corresponds to the lifecycle of the
network layer membership.
In the submitter's case, ieee80211_ioctl_updatemulti() attempts to
reprogram the (parent, physical) ifnet{} memberships in response
to a change in membership on the (child, virtual) VAP ifnet, using
a batched update mechanism. These updates happen independently from
the network layer, causing a "false negative" assertion failure.
There are possibly other use cases where this KASSERT() may be triggered
by other networking stack activity (e.g. where a nesting relationship
exists between multiple ifnet{} instances). This suggests that further
review of FreeBSD's approach to nested ifnet relationships is needed.
MFC after: 6 weeks
Submitted by: adrian@
The m_tag struct does not know about vnet context and the pf_mtag_free()
callback is called unaware of current vnet. This causes a panic.
Reviewed by: Nikos Vassiliadis, trociny@
ifi_oqdrops. This is a temporary workaround until ifqueue(9) vanishes.
While here, remove the pointless ifi_vhid assignment. It has
sense only when we are exporting ifaddrs, not ifnets.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
linking NIC Receive Side Scaling (RSS) to the network stack's
connection-group implementation. This prototype (and derived patches)
are in use at Juniper and several other FreeBSD-using companies, so
despite some reservations about its maturity, merge the patch to the
base tree so that it can be iteratively refined in collaboration rather
than maintained as a set of gradually diverging patch sets.
(1) Merge a software implementation of the Toeplitz hash specified in
RSS implemented by David Malone. This is used to allow suitable
pcbgroup placement of connections before the first packet is
received from the NIC. Software hashing is generally avoided,
however, due to high cost of the hash on general-purpose CPUs.
(2) In in_rss.c, maintain authoritative versions of RSS state intended
to be pushed to each NIC, including keying material, hash
algorithm/ configuration, and buckets. Provide software-facing
interfaces to hash 2- and 4-tuples for IPv4 and IPv6 using both
the RSS standardised Toeplitz and a 'naive' variation with a hash
efficient in software but with poor distribution properties.
Implement rss_m2cpuid()to be used by netisr and other load
balancing code to look up the CPU on which an mbuf should be
processed.
(3) In the Ethernet link layer, allow netisr distribution using RSS as
a source of policy as an alternative to source ordering; continue
to default to direct dispatch (i.e., don't try and requeue packets
for processing on the 'right' CPU if they arrive in a directly
dispatchable context).
(4) Allow RSS to control tuning of connection groups in order to align
groups with RSS buckets. If a packet arrives on a protocol using
connection groups, and contains a suitable hardware-generated
hash, use that hash value to select the connection group for pcb
lookup for both IPv4 and IPv6. If no hardware-generated Toeplitz
hash is available, we fall back on regular PCB lookup risking
contention rather than pay the cost of Toeplitz in software --
this is a less scalable but, at my last measurement, faster
approach. As core counts go up, we may want to revise this
strategy despite CPU overhead.
Where device drivers suitably configure NICs, and connection groups /
RSS are enabled, this should avoid both lock and line contention during
connection lookup for TCP. This commit does not modify any device
drivers to tune device RSS configuration to the global RSS
configuration; patches are in circulation to do this for at least
Chelsio T3 and Intel 1G/10G drivers. Currently, the KPI for device
drivers is not particularly robust, nor aware of more advanced features
such as runtime reconfiguration/rebalancing. This will hopefully prove
a useful starting point for refinement.
No MFC is scheduled as we will first want to nail down a more mature
and maintainable KPI/KBI for device drivers.
Sponsored by: Juniper Networks (original work)
Sponsored by: EMC/Isilon (patch update and merge)
AppleTalk was a network transport protocol for Apple Macintosh devices
in 80s and then 90s. Starting with Mac OS X in 2000 the AppleTalk was
a legacy protocol and primary networking protocol is TCP/IP. The last
Mac OS X release to support AppleTalk happened in 2009. The same year
routing equipment vendors (namely Cisco) end their support.
Thus, AppleTalk won't be supported in FreeBSD 11.0-RELEASE.
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
interface, in the r241616 a crutch was provided. It didn't work well, and
finally we decided that it is time to break ABI and simply make if_baudrate
a 64-bit value. Meanwhile, the entire struct if_data was reviewed.
o Remove the if_baudrate_pf crutch.
o Make all fields of struct if_data fixed machine independent size. The
notion of data (packet counters, etc) are by no means MD. And it is a
bug that on amd64 we've got a 64-bit counters, while on i386 32-bit,
which at modern speeds overflow within a second.
This also removes quite a lot of COMPAT_FREEBSD32 code.
o Give 16 bit for the ifi_datalen field. This field was provided to
make future changes to if_data less ABI breaking. Unfortunately the
8 bit size of it had effectively limited sizeof if_data to 256 bytes.
o Give 32 bits to ifi_mtu and ifi_metric.
o Give 64 bits to the rest of fields, since they are counters.
__FreeBSD_version bumped.
Discussed with: emax
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
after r262763 it started to return locked mutexes to UMA. To fix that,
conditionally unlock the mutex in the destructor.
Tested by: "Sergey V. Dyatko" <sergey.dyatko@gmail.com>
- Use counter(9) for rt_pksent (former rt_rmx.rmx_pksent). This
removes another cache trashing ++ from packet forwarding path.
- Create zini/fini methods for the rtentry UMA zone. Via initialize
mutex and counter in them.
- Fix reporting of rmx_pksent to routing socket.
- Fix netstat(1) to report "Use" both in kvm(3) and sysctl(3) mode.
The change is mostly targeted for stable/10 merge. For head,
rt_pksent is expected to just disappear.
Discussed with: melifaro
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
RADIX_NODE_HEAD_LOCK as grabbing the write lock,
but RADIX_NODE_HEAD_LOCK_ASSERT as checking the read lock.
Submitted by: Vijay Singh <vijju.singh at gmail.com>
MFC after: 1 month
were primarily used to size the sysctl name list macros that were removed
in r254295. A few other constants either did not have an associated
sysctl node, or the associated node used OID_AUTO instead.
PR: ports/184525 (exp-run)
tested and is unfinished. However, I've tested my version,
it works okay. As before it is unfinished: timeout aren't
driven by TCP session state. To enable the HASH_ALL mode,
one needs in kernel config:
options FLOWTABLE_HASH_ALL
o Reduce the alignment on flentry to 64 bytes. Without
the FLOWTABLE_HASH_ALL option, twice less memory would
be consumed by flows.
o API to ip_output()/ip6_output() got even more thin: 1 liner.
o Remove unused unions. Simply use fle->f_key[].
o Merge all IPv4 code into flowtable_lookup_ipv4(), and do same
flowtable_lookup_ipv6(). Stop copying data to on stack
sockaddr structures, simply use key[] on stack.
o Move code from flowtable_lookup_common() that actually works
on insertion into flowtable_insert().
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
- netmap pipes, providing bidirectional blocking I/O while moving
100+ Mpps between processes using shared memory channels
(no mistake: over one hundred million. But mind you, i said
*moving* not *processing*);
- kqueue support (BHyVe needs it);
- improved user library. Just the interface name lets you select a NIC,
host port, VALE switch port, netmap pipe, and individual queues.
The upcoming netmap-enabled libpcap will use this feature.
- optional extra buffers associated to netmap ports, for applications
that need to buffer data yet don't want to make copies.
- segmentation offloading for the VALE switch, useful between VMs.
and a number of bug fixes and performance improvements.
My colleagues Giuseppe Lettieri and Vincenzo Maffione did a substantial
amount of work on these features so we owe them a big thanks.
There are some external repositories that can be of interest:
https://code.google.com/p/netmap
our public repository for netmap/VALE code, including
linux versions and other stuff that does not belong here,
such as python bindings.
https://code.google.com/p/netmap-libpcap
a clone of the libpcap repository with netmap support.
With this any libpcap client has access to most netmap
feature with no recompilation. E.g. tcpdump can filter
packets at 10-15 Mpps.
https://code.google.com/p/netmap-ipfw
a userspace version of ipfw+dummynet which uses netmap
to send/receive packets. Speed is up in the 7-10 Mpps
range per core for simple rulesets.
Both netmap-libpcap and netmap-ipfw will be merged upstream at some
point, but while this happens it is useful to have access to them.
And yes, this code will be merged soon. It is infinitely better
than the version currently in 10 and 9.
MFC after: 3 days
insert flow entry. During the route lookup the critical section is
exited. It may happen, that after route lookup we will be executed
on an other CPU that already has such flowentry. Before this change
we simply freed the flowentry and returned to ip_output() with
failure.
Actually there is nothing wrong with using previously allocated
flow entry, updating it properly. Thus, make flowentry_insert()
return the new either old fle, and make use of it.
Count reuses as "collisions" and real inserts as "inserts".
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
race prone. Some just gather statistics, but some are later used in
different calculations.
A real problem was the race provoked underflow of the states_cur counter
on a rule. Once it goes below zero, it wraps to UINT32_MAX. Later this
value is used in pf_state_expires() and any state created by this rule
is immediately expired.
Thus, make fields states_cur, states_tot and src_nodes of struct
pf_rule be counter(9)s.
Thanks to Dennis for providing me shell access to problematic box and
his help with reproducing, debugging and investigating the problem.
Thanks to: Dennis Yusupoff <dyr smartspb.net>
Also reported by: dumbbell, pgj, Rambler
Sponsored by: Nginx, Inc.
Some of the collisions that are occuring are due to flowtable lookups
that succeed but have an invalid lle - typically because the L2 adjacency
lookup hasn't completed. This would lead to a follow-up insert which
would then fail (ie, collision) and the code would fall through to doing
a slow-path L2/L3 lookup in the netinet/netinet6 code.
This patch simply aborts storing a new flowtable entry if the lle isn't
yet valid.
Whilst I'm here, add a new pcpu counter for the item so the number of
failures can be tracked separately from generic "collisions."
Reviewed by: glebius
MFC after: 10 days
Sponsored by: Netflix, Inc.
and probably is a leftover from first prototyping by Kip. The
non-pcpu implementation used mutexes, so it doubtfully worked
better than simple routing lookup.
o Use UMA_ZONE_PCPU zone for pointers instead of [MAXCPU] arrays,
use zpcpu_get() to access data in there.
o Substitute own single list implementation with SLIST(). This
has two functional side effects:
- new flows go into head of a list, before they went to tail.
- a bug when incorrect flow was deleted in flow cleaner is
fixed.
o Due to cache line alignment, there is no reason to keep
different zones for IPv4 and IPv6 flows. Both consume one
cache line, real size of allocation is equal.
o Rely on that f_hash, f_rt, f_lle are stable during fle
lifetime, remove useless volatile quilifiers.
o More INET/INET6 splitting.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
- ip_output() and ip_output6() simply call flowtable_lookup(),
passing mbuf and address family. That's the only code under
#ifdef FLOWTABLE in the protocols code now.
o Revamp statistics gathering and export.
- Remove hand made pcpu stats, and utilize counter(9).
- Snapshot of statistics is available via 'netstat -rs'.
- All sysctls are moved into net.flowtable namespace, since
spreading them over net.inet isn't correct.
o Properly separate at compile time INET and INET6 parts.
o General cleanup.
- Remove chain of multiple flowtables. We simply have one for
IPv4 and one for IPv6.
- Flowtables are allocated in flowtable.c, symbols are static.
- With proper argument to SYSINIT() we no longer need flowtable_ready.
- Hash salt doesn't need to be per-VNET.
- Removed rudimentary debugging, which use quite useless in dtrace era.
The runtime behavior of flowtable shouldn't be changed by this commit.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
in the sysctl_root().
Note: SYSCTL_VNET_* macros can be removed as well. All is
needed to virtualize a sysctl oid is set CTLFLAG_VNET on it.
But for now keep macros in place to avoid large code churn.
Sponsored by: Nginx, Inc.
callback providers. link_init_sdl() function can be used to
fill most of the parameters. Use caller stack instead of
allocation / freing memory for each request. Do not drop support
for extra-long (probably non-existing) link-layer protocols by
introducing link_alloc_sdl() (used by if_resolvemulti() callback)
and link_free_sdl() (used by caller).
Since this change breaks KBI, MFC requires slightly different approach
(link_init_sdl() auto-allocating buffer if necessary to handle cases
with unmodified if_resolvemulti() callers).
MFC after: 2 weeks
has the same prefix as some other alias on the same interface, use
newly-added rt_addrmsg() instead of hand-rolled in_addralias_rtmsg().
This eliminates the following rtsock messages:
Pinned RTM_ADD for prefix (for alias addition).
Pinned RTM_DELETE for prefix (for alias withdrawal).
Example (got 10.0.0.1/24 on vlan4, playing with 10.0.0.2/24):
before commit, addition:
got message of size 116 on Fri Jan 10 14:13:15 2014
RTM_NEWADDR: address being added to iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
got message of size 192 on Fri Jan 10 14:13:15 2014
RTM_ADD: Add Route: len 192, pid: 0, seq 0, errno 0, flags:<UP,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK>
10.0.0.0 10.0.0.2 (255) ffff ffff ff
after commit, addition:
got message of size 116 on Fri Jan 10 13:56:26 2014
RTM_NEWADDR: address being added to iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 14.0.0.2 14.0.0.255
before commit, wihdrawal:
got message of size 192 on Fri Jan 10 13:58:59 2014
RTM_DELETE: Delete Route: len 192, pid: 0, seq 0, errno 0, flags:<UP,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK>
10.0.0.0 10.0.0.2 (255) ffff ffff ff
got message of size 116 on Fri Jan 10 13:58:59 2014
RTM_DELADDR: address being removed from iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
adter commit, withdrawal:
got message of size 116 on Fri Jan 10 14:14:11 2014
RTM_DELADDR: address being removed from iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
Sending both RTM_ADD/RTM_DELETE messages to rtsock is completely wrong
(and requires some hacks to keep prefix in route table on RTM_DELETE).
I've tested this change with quagga (no change) and bird (*).
bird alias handling is already broken in *BSD sysdep code, so nothing
changes here, too.
I'm going to MFC this change if there will be no complains about behavior
change.
While here, fix some style(9) bugs introduced by r260488
(pointed by glebius and bde).
Sponsored by: Yandex LLC
MFC after: 4 weeks
Adding/deleting interface addresses involves access to 3 different subsystems,
int different parts of code. Each call can fail, so reporting successful
operation by rtsock in the middle of the process error-prone.
Further split routing notification API and actual rtsock calls via creating
public-available rt_addrmsg() / rt_routemsg() functions with "private"
rtsock_* backend.
MFC after: 2 weeks
