Also disable relaxed ordering as recommended by data sheet for
PCI-X devices. For PCI-X BCM5704, set maximum outstanding split
transactions to 0 as indicated by data sheet.
For BCM5703 in PCI-X mode, DMA read watermark should be less than
or equal to maximum read byte count configuration. Enforce this
limitation in DMA read watermark configuration.
chip revision often found in the blades and resulting in interfaces
not sensing carrier signal. Looking at all problem reports it
appears that it only affects some very specific silicon revision
(ASIC (0x57081021); Rev (B2)) and version of the PHY that
supports 1000baseSX-FDX media only. Therefore, narrow the scope of
workaround to combination of that revision and media type. Given
that the first report on this issue is dated back to 2007, there is
not much hope that this issue will ever be properly resolved.
Among affected systems are IBM HS21, Intel SBXD132 and HP BL460c.
PR: 118238, 122551, 140970
MFC after: 1 month
are referenced directly from ivar pointer. It's to do like what other
buses do. [1]
o changes exported prototypes. It doesn't use struct siba_* structures
anymore that instead of it it uses only device_t.
o removes duplicate code and debug messages.
o style(9)
Pointed out by: imp [1]
Setting the new sysctl MIB "debug.acpi.enable_debug_objects" to a non-zero
value enables us to print Debug object when something is written to it.
- Allow users to disable interpreter slack mode. Setting the new tunable
"debug.acpi.interpreter_slack" to zero disables some workarounds for common
BIOS mistakes and enables strict ACPI implementations by the specification.
pmc_flush_logfile is now non-blocking and just ask the kernel
to shutdown the file. From that point, no more data is
accepted by the log thread and when the last buffer is flushed
the file is closed.
This will remove a deadlock between pmcstat asking for
flush while it cannot flush the pipe itself.
MFC after: 3 days
interface didn't be attached automatically at boot time so changes a
approach to attach children based on leveraging some newbus niceties.
Submitted by: nwhitehorn
- change the way in which command queue overflow is handled;
- do not expose to CAM two command slots, used for driver's internal purposes;
- allow driver to use up to 1024 command slots, instead of 256 before.
88E1149 PHY. This will fix intermittent watchdog timeouts as well
as very slow network performance on 88E8072 Yukon Extreme.
PR: kern/144148
MFC after: 1 week
o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check
does not generate excessive interrupts any more so we don't need
to have two copies of interrupt handler.
While I'm here remove two STAT_PUT_IDX register accesses in LE
status event handler. After r204539 msk(4) always sync status LEs
so there is no need to resort to reading STAT_PUT_IDX register to
know the end of status LE processing. Just trust status LE's
ownership bit.
countdown timer register. The timer resolution may vary among
controllers but the value would be represented by core clock
cycles. msk(4) will automatically computes number of required clock
cycles from given micro-seconds unit.
The default interrupt holdoff timer value is 100us which will
ensure less than 10k interrupts under load. The timer value can be
changed with dev.mskc.0.int_holdoff sysctl node.
Note, the interrupt moderation is shared resource on dual-port
controllers so you can't use separate interrupt moderation value
for each port. This means we can't stop interrupt moderation in
driver stop routine. Also have msk_tick() reclaim transmitted Tx
buffers as safety belt. With this change there is no need to check
missing Tx completion interrupt in watchdog handler, so remove it.
full-duplex. Previously msk(4) used to allow flow-control on
1000baseT half-duplex media. Also GMAC pause is enabled if link
partner is capable of handling it.
While I'm here use IFM_OPTIONS instead of using IFM_GMASK to check
optional flags of link.
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.
Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.
Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.
While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.
PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week
the issue. I still have no idea why TSO does not work on this
controller. davidch@ also confirmed there is no known TSO related
issues for this controller.
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
Reviewed by: davidch
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
for controllers like 88E8053 which reports two MSI messages.
Because we don't get anything useful things with 2 MSI messages,
allocating 1 MSI message would be more sane approach.
While I'm here, enable MSI for dual-port controllers too. Because
status block is shared for dual-port controllers, I don't think
msk(4) will encounter problem for using MSI on dual-port
controllers.
The register offset is not valid on 88E8072 controller. Also don't
blindly increase max read request size to 4096, instead, use 2048
which seems to be more sane value and only change the value if the
hardware default size(512) was used on that register.
For PCIX controllers, use system defined constant rather than using
magic value.
While I'm here stop showing negotiated link width.
not require checksum LE configuration if checksum start and write
position is the same as before. So keep track last checksum start
and write position and insert new LE whenever the position is
changed. This reduces number of LEs used in TX path as well as
slightly enhance TX performance.
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.
This fixes a panic when running tcpdump on a cxgb interface.
- Add a separate palette data for 8-bit DAC mode when SC_PIXEL_MODE is set
and fill it up with default gray-scale palette data for text. Now we don't
have to set `hint.sc.0.vesa_mode' to get the default palette data.
- Add a new adapter flag, V_ADP_DAC8 to track whether the controller is
using 8-bit palette format and load correct palette when switching modes.
- Set 8-bit DAC mode only for non-VGA compatible graphics mode.
change and have isp_make_here scan the whole bus which will then scan all
luns.
I think xpt_rescan needs to be fixed, but that's a separable issue.
Suggested by: Alexander
not support TSO over VLAN if VLAN hardware tagging is disabled so
there is no need to check VLAN here.
While I'm here make sure to pullup IP/TCP headers in the first
buffer.
GEM_MIF_CONFIG_MDI0 cannot be trusted when the firmware has powered
down the chip so the internal transceiver has to be hardcoded. This
is also in line with the AppleGMACEthernet driver, which just doesn't
distinguish between internal/external transceiver and MDIO/MDI1
respectively in the first place. Tested by: Andreas Tobler
MFC after: 1 week
frame, make sure to update VLAN capabilities whenever jumbo frame
is configured.
While I'm here rearrange interface capabilities configuration. The
controller requires VLAN hardware tagging to make TSO work on VLANs
so explicitly check this requirement.
Tx DMA burst size 2048, I beleive PCIe maximum read request size
also should match to the value of Tx DMA burst size. With this
change I can get more than 800Mbps for TCP bulk transfers.
Previously I was not able to get more than 700Mbps. If I enable TSO
it now shows 927Mbps.
to make TSO work on VLAN. So if VLAN hardware tagging is disabled
explicitly clear TSO on VLAN. While I'm here remove duplicated
VLAN_CAPABILITIES call.
o uses v4 firmware instead of v3. A port will be committed to create
the bwn firmware module.
o supports B/G and LP(low power) PHYs.
o supports 32 / 64 bits DMA operations.
o tested on big / little endian machines so should work on all
architectures.
It'd not connected to the build until the firmware port is committed.
