validity of ro->ro_rt first. This prevents crashing on any non-normally
routed IP packet.
Coverity CID: 162 (incorrectly, it was re-introduced by previous commit)
support a network w/ split mtu's by assigning each host route the correct
mtu. an aspiring programmer could write a daemon to probe hosts and find
out if they support a larger mtu.
timeouts for TCP and T/TCP connections in the TIME_WAIT
state, and we had two separate timed wait queues for them.
Now that is has gone, the timeout is always 2*MSL again,
and there is no reason to keep two queues (the first was
unused anyway!).
Also, reimplement the remaining queue using a TAILQ (it
was technically impossible before, with two queues).
TSO is only used if we are in a pure bulk sending state. The presence of
TCP-MD5, SACK retransmits, SACK advertizements, IPSEC and IP options prevent
using TSO. With TSO the TCP header is the same (except for the sequence number)
for all generated packets. This makes it impossible to transmit any options
which vary per generated segment or packet.
The length of TSO bursts is limited to TCP_MAXWIN.
The sysctl net.inet.tcp.tso globally controls the use of TSO and is enabled.
TSO enabled sends originating from tcp_output() have the CSUM_TCP and CSUM_TSO
flags set, m_pkthdr.csum_data filled with the header pseudo-checksum and
m_pkthdr.tso_segsz set to the segment size (net payload size, not counting
IP+TCP headers or TCP options).
IPv6 currently lacks a pseudo-header checksum function and thus doesn't support
TSO yet.
Tested by: Jack Vogel <jfvogel-at-gmail.com>
Sponsored by: TCP/IP Optimization Fundraise 2005
o add IFCAP_TSO[46] for drivers to announce this capability for IPv4 and IPv6
o add CSUM_TSO flag to mbuf pkthdr csum_flags field
o add tso_segsz field to mbuf pkthdr
o enhance ip_output() packet length check to allow for large TSO packets
o extend tcp_maxmtu[46]() with a flag pointer to pass interface capabilities
o adjust all callers of tcp_maxmtu[46]() accordingly
Discussed on: -current, -net
Sponsored by: TCP/IP Optimization Fundraise 2005
and skip over the normal IP processing.
Add a supporting function ifa_ifwithbroadaddr() to verify and validate the
supplied subnet broadcast address.
PR: kern/99558
Tested by: Andrey V. Elsukov <bu7cher-at-yandex.ru>
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
bad under high load. For example with 40k sockets and 25k tcptw
entries, connect() syscall can run for seconds. Debugging showed
that it iterates the cycle millions times and purges thousands of
tcptw entries at a time.
Besides practical unusability this change is architecturally
wrong. First, in_pcblookup_local() is used in connect() and bind()
syscalls. No stale entries purging shouldn't be done here. Second,
it is a layering violation.
o Return back the tcptw purging cycle to tcp_timer_2msl_tw(),
that was removed in rev. 1.78 by rwatson. The commit log of this
revision tells nothing about the reason cycle was removed. Now
we need this cycle, since major cleaner of stale tcptw structures
is removed.
o Disable probably necessary, but now unused
tcp_twrecycleable() function.
Reviewed by: ru
for example:
fwd tablearg ip from any to table(1)
where table 1 has entries of the form:
1.1.1.0/24 10.2.3.4
208.23.2.0/24 router2
This allows trivial implementation of a secondary routing table implemented
in the firewall layer.
I expect more work (under discussion with Glebius) to follow this to clean
up some of the messy parts of ipfw related to tables.
Reviewed by: Glebius
MFC after: 1 month
in older versions of FreeBSD. This option is pointless as it is needed in just
about every interesting usage of forward that I have ever seen. It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x or 7.x
Reviewed by: glebius
MFC after: 1 week
were unused or already in if_var.h so add if_name() to if_var.h and
remove net_osdep.h along with all references to it.
Longer term we may want to kill off if_name() entierly since all modern
BSDs have if_xname variables rendering it unnecessicary.
tcp_twstart(), but not to the other, tcp_detach(), as the socket is
already being torn down and therefore there are no listeners. This avoids
a panic if kqueue state is registered on the socket at close(), and
eliminates to XXX comments. There is one case remaining in which
tcp_discardcb() reaches up to the socket layer as part of the TCP host
cache, which would be good to avoid.
Reported by: Goran Gajic <ggajic at afrodita dot rcub dot bg dot ac dot yu>
function, pru_close, to notify protocols that the file descriptor or
other consumer of a socket is closing the socket. pru_abort is now a
notification of close also, and no longer detaches. pru_detach is no
longer used to notify of close, and will be called during socket
tear-down by sofree() when all references to a socket evaporate after
an earlier call to abort or close the socket. This means detach is now
an unconditional teardown of a socket, whereas previously sockets could
persist after detach of the protocol retained a reference.
This faciliates sharing mutexes between layers of the network stack as
the mutex is required during the checking and removal of references at
the head of sofree(). With this change, pru_detach can now assume that
the mutex will no longer be required by the socket layer after
completion, whereas before this was not necessarily true.
Reviewed by: gnn
( and where appropriate the destruction) of the pcb mutex to the init/finit
functions of the pcb zones.
This allows locking of the pcb entries and race condition free comparison
of the generation count.
Rearrange locking a bit to avoid extra locking operation to update the generation
count in in_pcballoc(). (in_pcballoc now returns the pcb locked)
I am planning to convert pcb list handling from a type safe to a reference count
model soon. ( As this allows really freeing the PCBs)
Reviewed by: rwatson@, mohans@
MFC after: 1 week
parameter that can specify configuration parameters:
o rev cloner api's to add optional parameter block
o add SIOCCREATE2 that accepts parameter data
o rev vlan support to use new api (maintain old code)
Reviewed by: arch@
except in places dealing with ifaddr creation or destruction; and
in such special places incomplete ifaddrs should never be linked
to system-wide data structures. Therefore we can eliminate all the
superfluous checks for "ifa->ifa_addr != NULL" and get ready
to the system crashing honestly instead of masking possible bugs.
Suggested by: glebius, jhb, ru
used since FreeBSD-SA-06:04.ipfw.
Adopt send_reject6 to what had been done for legacy IP: no longer
send or permit sending rejects for any but the first fragment.
Discussed with: oleg, csjp (some weeks ago)
o don't assign remote/local host/port information manually between provided
struct in_conninfo and struct syncache, bcopy() it instead
o rename sc_tsrecent to sc_tsreflect in struct syncache to better capture
the purpose of this field
o rename sc_request_r_scale to sc_requested_r_scale for ditto reasons
o fix IPSEC error case printf's to report correct function name
o in syncache_socket() only transpose enhanced tcp options parameters to
struct tcpcb when the inpcb doesn't has TF_NOOPT set
o in syncache_respond() reorder stack variables
o in syncache_respond() remove bogus KASSERT()
No functional changes.
Sponsored by: TCP/IP Optimization Fundraise 2005
o redefine the parameter 'is_syn' to 'flags', add TO_SYN flag and adjust its
usage accordingly
o update the comments to the tcp_dooptions() invocation in
tcp_input():after_listen to reflect reality
o move the logic checking the echoed timestamp out of tcp_dooptions() to the
only place that uses it next to the invocation described in the previous
item
o adjust parsing of TCPOPT_SACK_PERMITTED to use the same style as the others
o add comments in to struct tcpopt.to_flags #defines
No functional changes.
Sponsored by: TCP/IP Optimization Fundraise 2005
infinite loop with net.inet6.ip6.fw.deny_unknown_exthdrs=0.
- Teach ipv6 and ipencap as they appear in an IPv4/IPv6 over IPv6
tunnel.
- Test the next extention header even when the routing header type
is unknown with net.inet6.ip6.fw.deny_unknown_exthdrs=0.
Found by: xcast-fan-club
MFC after: 1 week
memory location for already existing/initialized mutexes. With random
data in the memory location this fails (ie. after a soft reboot).
Reported by: brueffer, YAMAMOTO Shigeru
Submitted by: YAMAMOTO Shigeru <shigeru-at-iij.ad.jp>
ACK the SYN as required by RFC793, rather than ignoring it. NetBSD
have had a similar change since 1999.
PR: 93236
Submitted by: Grant Edwards <grante@visi.com>
MFC after: 1 month
as possible for the syncache_add() case. The syncache timer no longer
aquires the tcpinfo lock and timeout/retransmit runs can happen in
parallel with bucket granularity.
On a P4 the additional locks cause a slight degression of 0.7% in tcp
connections per second. When IP and TCP input are deserialized and
can run in parallel this little overhead can be neglected. The syncookie
handling still leaves room for improvement and its random salts may be
moved to the syncache bucket head structures to remove the second lock
operation currently required for it. However this would be a more
involved change from the way syncookies work at the moment.
Reviewed by: rwatson
Tested by: rwatson, ps (earlier version)
Sponsored by: TCP/IP Optimization Fundraise 2005
- 'tag' & 'untag' action parameters.
- 'tagged' & 'limit' rule options.
Rule examples:
pipe 1 tag tablearg ip from table(1) to any
allow ip from any to table(2) tagged tablearg
allow tcp from table(3) to any 25 setup limit src-addr tablearg
sbin/ipfw/ipfw2.c:
1) new macros
GET_UINT_ARG - support of 'tablearg' keyword, argument range checking.
PRINT_UINT_ARG - support of 'tablearg' keyword.
2) strtoport(): do not silently truncate/accept invalid port list expressions
like: '1,2-abc' or '1,2-3-4' or '1,2-3x4'. style(9) cleanup.
Approved by: glebius (mentor)
MFC after: 1 month
dropped. This prevents a bug introduced during the socket/pcb refcounting
work from occuring, in which occasionally the retransmit timer may fire
after a connection has been reset, resulting in the resulting R|A TCP
packet having a source port of 0, as the port reservation has been
released.
While here, fixing up some RUNLOCK->WUNLOCK bugs.
MFC after: 1 month
(1) bpf peer attaches to interface netif0
(2) Packet is received by netif0
(3) ifp->if_bpf pointer is checked and handed off to bpf
(4) bpf peer detaches from netif0 resulting in ifp->if_bpf being
initialized to NULL.
(5) ifp->if_bpf is dereferenced by bpf machinery
(6) Kaboom
This race condition likely explains the various different kernel panics
reported around sending SIGINT to tcpdump or dhclient processes. But really
this race can result in kernel panics anywhere you have frequent bpf attach
and detach operations with high packet per second load.
Summary of changes:
- Remove the bpf interface's "driverp" member
- When we attach bpf interfaces, we now set the ifp->if_bpf member to the
bpf interface structure. Once this is done, ifp->if_bpf should never be
NULL. [1]
- Introduce bpf_peers_present function, an inline operation which will do
a lockless read bpf peer list associated with the interface. It should
be noted that the bpf code will pickup the bpf_interface lock before adding
or removing bpf peers. This should serialize the access to the bpf descriptor
list, removing the race.
- Expose the bpf_if structure in bpf.h so that the bpf_peers_present function
can use it. This also removes the struct bpf_if; hack that was there.
- Adjust all consumers of the raw if_bpf structure to use bpf_peers_present
Now what happens is:
(1) Packet is received by netif0
(2) Check to see if bpf descriptor list is empty
(3) Pickup the bpf interface lock
(4) Hand packet off to process
From the attach/detach side:
(1) Pickup the bpf interface lock
(2) Add/remove from bpf descriptor list
Now that we are storing the bpf interface structure with the ifnet, there is
is no need to walk the bpf interface list to locate the correct bpf interface.
We now simply look up the interface, and initialize the pointer. This has a
nice side effect of changing a bpf interface attach operation from O(N) (where
N is the number of bpf interfaces), to O(1).
[1] From now on, we can no longer check ifp->if_bpf to tell us whether or
not we have any bpf peers that might be interested in receiving packets.
In collaboration with: sam@
MFC after: 1 month
Since tags are kept while packet resides in kernelspace, it's possible to
use other kernel facilities (like netgraph nodes) for altering those tags.
Submitted by: Andrey Elsukov <bu7cher at yandex dot ru>
Submitted by: Vadim Goncharov <vadimnuclight at tpu dot ru>
Approved by: glebius (mentor)
Idea from: OpenBSD PF
MFC after: 1 month
a defensive programming measure.
Note that whilst these members are not used by the ip_output()
path, we are passing an instance of struct ip_moptions here
which is declared on the stack (which could be considered a
bad thing).
ip_output() does not consume struct ip_moptions, but in case it
does in future, declare an in_multi vector on the stack too to
behave more like ip_findmoptions() does.
as not connected. In soclose() case rip_detach() will kill inpcb for
us later.
It makes rawconnect regression test do not panic a system.
Reviewed by: rwatson
X-MFC after: with all 1th April inpcb changes
connections and get rid of the flow_id as it is not guaranteed to be stable
some (most?) current implementations seem to just zero it out.
PR: kern/88664
Reported by: jylefort
Submitted by: Joost Bekkers (w/ changes)
Tested by "regisr" <regisrApoboxDcom>
By making the imo_membership array a dynamically allocated vector,
this minimizes disruption to existing IPv4 multicast code. This
change breaks the ABI for the kernel module ip_mroute.ko, and may
cause a small amount of churn for folks working on the IGMPv3 merge.
Previously, sockets were subject to a compile-time limitation on
the number of IPv4 group memberships, which was hard-coded to 20.
The imo_membership relationship, however, is 1:1 with regards to
a tuple of multicast group address and interface address. Users who
ran routing protocols such as OSPF ran into this limitation on machines
with a large system interface tree.
seperately. Also use pfil hook/unhook instead of keeping the check
functions in pfil just to return there based on the sysctl. While here fix
some whitespace on a nearby SYSCTL_ macro.
for signicantly optimized UDP socket I/O when using a single UDP
socket from many threads or processes that share it, by avoiding
significant locking and other overhead in the general sosend()
path that isn't necessary for simple datagram sockets. Specifically,
this change results in a significant performance improvement for
threaded name service in BIND9 under load.
Suggested by: Jinmei_Tatsuya at isc dot org
after ipsec4_output processing else KAME IPSec using the handbook
configuration with gif(4) will panic the kernel.
Problem reported by: t. patterson <tp lot.org>
Tested by: t. patterson <tp lot.org>
return NULL. In principle this shouldn't change the behavior, but
avoids returning a potentially invalid/inappropriate pointer to
the caller.
Found with: Coverity Prevent (tm)
Submitted by: pjd
MFC after: 3 months
the fact that the loop through inpcb's in udp_input() tracks the
last inpcb while looping. We keep that name in the calling loop
but not in the delivery routine itself.
MFC after: 3 months
into in_pcbdrop(). Expand logic to detach the inpcb from its bound
address/port so that dropping a TCP connection releases the inpcb resource
reservation, which since the introduction of socket/pcb reference count
updates, has been persisting until the socket closed rather than being
released implicitly due to prior freeing of the inpcb on TCP drop.
MFC after: 3 months
common pcb tear-down logic into tcp_detach(), which is called from
either. Invoke tcp_drop() from the tcp_usr_abort() path rather than
tcp_disconnect(), as we want to drop it immediately not perform a
FIN sequence. This is one reason why some people were experiencing
panics in sodealloc(), as the netisr and aborting thread were
simultaneously trying to tear down the socket. This bug could often
be reproduced using repeated runs of the listenclose regression test.
MFC after: 3 months
PR: 96090
Reported by: Peter Kostouros <kpeter at melbpc dot org dot au>, kris
Tested by: Peter Kostouros <kpeter at melbpc dot org dot au>, kris
number state, rather than re-using pcbinfo. This introduces some
additional mutex operations during isn query, but avoids hitting the TCP
pcbinfo lock out of yet another frequently firing TCP timer.
MFC after: 3 months
holding the inpcb lock is sufficient to prevent races in reading
the address and port, as both the inpcb lock and pcbinfo lock are
required to change the address/port.
Improve consistency of spelling in assertions about inp != NULL.
MFC after: 3 months
reference. For now, we allow the possibility that the in_ppcb
pointer in the inpcb may be NULL if a timewait socket has had its
tcptw structure recycled. This allows tcp_timewait() to
consistently unlock the inpcb.
Reported by: Kazuaki Oda <kaakun at highway dot ne dot jp>
MFC after: 3 months
(tcp_sack_output_debug checks cached hints aginst computed values by walking the
scoreboard and reports discrepancies). The sack hinting code has been stable for
many months now so it is time for the debug code to go. Leaving tcp_sack_output_debug
ifdef'ed out in case we need to resurrect it at a later point.
tcp_timewait(). This corrects a bug (or lack of fixing of a bug)
in tcp_input.c:1.295.
Submitted by: Kazuaki Oda <kaakun at highway dot ne dot jp>
MFC after: 3 months
NULL. We currently do allow this to happen, but may want to remove that
possibility in the future. This case can occur when a socket is left
open after TCP wraps up, and the timewait state is recycled. This will
be cleaned up in the future.
Found by: Kazuaki Oda <kaakun at highway dot ne dot jp>
MFC after: 3 months
The INP_DROPPED check replaces the current NULL checks; the INP_TIMEWAIT
checks appear to have always been required, but not been there, which
is/was a bug. This avoids unconditionally casting of in_ppcb to a tcpcb,
when it may be a twtcb, which may have resulted in obscure ICMP-related
panics in earlier releases.
MFC after: 3 months
casts.
Consistently use intotw() to cast inp_ppcb pointers to struct tcptw *
pointers.
Consistently use intotcpcb() to cast inp_ppcb pointers to struct tcpcb *
pointers.
Don't assign tp to the results to intotcpcb() during variable declation
at the top of functions, as that is before the asserts relating to
locking have been performed. Do this later in the function after
appropriate assertions have run to allow that operation to be conisdered
safe.
MFC after: 3 months
immediately rather than jumping to the normal output handling, which
assumes we've pulled out the inpcb, which hasn't happened at this
point (and isn't necessary).
Return ECONNABORTED instead of EINVAL when the inpcb has entered
INP_TIMEWAIT or INP_DROPPED, as this is the documented error value.
This may correct the panic seen by Ganbold.
MFC after: 1 month
Reported by: Ganbold <ganbold at micom dot mng dot net>
disconnect for fully connected sockets was dropped, meaning that if
the socket was closed while the connection was alive, it would be
leaked. Structure tcp_usr_detach() so that there are two clear
parts: initiating disconnect, and reclaiming state, and reintroduce
the tcp_disconnect() call in the first part.
MFC after: 3 months
socket can have a tcp connection that has entered time wait
attached to it, in the event that shutdown() is called on the
socket and the FINs properly exchange before close(). In this
case we don't detach or free the inpcb, just leave the tcptw
detached and freed, but we must release the inpcb lock (which we
didn't previously).
MFC after: 3 months
pru_abort(), pru_detach(), and in_pcbdetach():
- Universally support and enforce the invariant that so_pcb is
never NULL, converting dozens of unnecessary NULL checks into
assertions, and eliminating dozens of unnecessary error handling
cases in protocol code.
- In some cases, eliminate unnecessary pcbinfo locking, as it is no
longer required to ensure so_pcb != NULL. For example, the receive
code no longer requires the pcbinfo lock, and the send code only
requires it if building a new connection on an otherwise unconnected
socket triggered via sendto() with an address. This should
significnatly reduce tcbinfo lock contention in the receive and send
cases.
- In order to support the invariant that so_pcb != NULL, it is now
necessary for the TCP code to not discard the tcpcb any time a
connection is dropped, but instead leave the tcpcb until the socket
is shutdown. This case is handled by setting INP_DROPPED, to
substitute for using a NULL so_pcb to indicate that the connection
has been dropped. This requires the inpcb lock, but not the pcbinfo
lock.
- Unlike all other protocols in the tree, TCP may need to retain access
to the socket after the file descriptor has been closed. Set
SS_PROTOREF in tcp_detach() in order to prevent the socket from being
freed, and add a flag, INP_SOCKREF, so that the TCP code knows whether
or not it needs to free the socket when the connection finally does
close. The typical case where this occurs is if close() is called on
a TCP socket before all sent data in the send socket buffer has been
transmitted or acknowledged. If INP_SOCKREF is found when the
connection is dropped, we release the inpcb, tcpcb, and socket instead
of flagging INP_DROPPED.
- Abort and detach protocol switch methods no longer return failures,
nor attempt to free sockets, as the socket layer does this.
- Annotate the existence of a long-standing race in the TCP timer code,
in which timers are stopped but not drained when the socket is freed,
as waiting for drain may lead to deadlocks, or have to occur in a
context where waiting is not permitted. This race has been handled
by testing to see if the tcpcb pointer in the inpcb is NULL (and vice
versa), which is not normally permitted, but may be true of a inpcb
and tcpcb have been freed. Add a counter to test how often this race
has actually occurred, and a large comment for each instance where
we compare potentially freed memory with NULL. This will have to be
fixed in the near future, but requires is to further address how to
handle the timer shutdown shutdown issue.
- Several TCP calls no longer potentially free the passed inpcb/tcpcb,
so no longer need to return a pointer to indicate whether the argument
passed in is still valid.
- Un-macroize debugging and locking setup for various protocol switch
methods for TCP, as it lead to more obscurity, and as locking becomes
more customized to the methods, offers less benefit.
- Assert copyright on tcp_usrreq.c due to significant modifications that
have been made as part of this work.
These changes significantly modify the memory management and connection
logic of our TCP implementation, and are (as such) High Risk Changes,
and likely to contain serious bugs. Please report problems to the
current@ mailing list ASAP, ideally with simple test cases, and
optionally, packet traces.
MFC after: 3 months
pru_abort(), pru_detach(), and in_pcbdetach():
- Universally support and enforce the invariant that so_pcb is
never NULL, converting dozens of unnecessary NULL checks into
assertions, and eliminating dozens of unnecessary error handling
cases in protocol code.
- In some cases, eliminate unnecessary pcbinfo locking, as it is no
longer required to ensure so_pcb != NULL. For example, in protocol
shutdown methods, and in raw IP send.
- Abort and detach protocol switch methods no longer return failures,
nor attempt to free sockets, as the socket layer does this.
- Invoke in_pcbfree() after in_pcbdetach() in order to free the
detached in_pcb structure for a socket.
MFC after: 3 months
- in_pcbdetach(), which removes the link between an inpcb and its
socket.
- in_pcbfree(), which frees a detached pcb.
Unlike the previous in_pcbdetach(), neither of these functions will
attempt to conditionally free the socket, as they are responsible only
for managing in_pcb memory. Mirror these changes into in6_pcbdetach()
by breaking it into in6_pcbdetach() and in6_pcbfree().
While here, eliminate undesired checks for NULL inpcb pointers in
sockets, as we will now have as an invariant that sockets will always
have valid so_pcb pointers.
MFC after: 3 months
rather than an error. Detaches do not "fail", they other occur or
the protocol flags SS_PROTOREF to take ownership of the socket.
soclose() no longer looks at so_pcb to see if it's NULL, relying
entirely on the protocol to decide whether it's time to free the
socket or not using SS_PROTOREF. so_pcb is now entirely owned and
managed by the protocol code. Likewise, no longer test so_pcb in
other socket functions, such as soreceive(), which have no business
digging into protocol internals.
Protocol detach routines no longer try to free the socket on detach,
this is performed in the socket code if the protocol permits it.
In rts_detach(), no longer test for rp != NULL in detach, and
likewise in other protocols that don't permit a NULL so_pcb, reduce
the incidence of testing for it during detach.
netinet and netinet6 are not fully updated to this change, which
will be in an upcoming commit. In their current state they may leak
memory or panic.
MFC after: 3 months
than an int, as an error here is not meaningful. Modify soabort() to
unconditionally free the socket on the return of pru_abort(), and
modify most protocols to no longer conditionally free the socket,
since the caller will do this.
This commit likely leaves parts of netinet and netinet6 in a situation
where they may panic or leak memory, as they have not are not fully
updated by this commit. This will be corrected shortly in followup
commits to these components.
MFC after: 3 months
reason, seems to be where new flags are getting defined:
INP_DROPPED - The protocol has terminated this connection and the socket
is not reusable: when the socket code enters the protocol,
an error is immediately returned. This will substitute for
NULLing the so_pcb socket field, helping to implement the
invariant that all valid sockets have valid pcb's in TCP.
INP_SOCKREF - The protocol has become the owner of the socket reference,
and will need to free it when freeing the pcb, which will
be used when a TCP socket is closed but still has queued
data.
MFC after: 1 month
multicast addresses from carp interface. [1]
o Rewrite carpdetach(), so that it does the following things: [1]
- Stops callouts.
- Decrements carp_suppress_preempt, if needed.
- Downs interface and sets CARP state to INIT.
- Calls carp_multicast_cleanup().
- Detaches softc from carp_if and if we are the last frees
the carp_if.
o Use new carpdetach() in carp_clone_destroy().
o In carp_ifdetach() acquire the carp_if lock and cleanup all
interfaces hanging on carp_if. [1]
o Make carp_ifdetach() static and use EVENT(9) to call it
from if_detach(). [2]
o In carp_setrun() exit if the softc doesn't have a valid pointer
to parent. [1]
Obtained from: OpenBSD [1]
Submitted by: Dan Lukes <dan obluda.cz> [2]
PR: kern/82908 [2]
net.inet.ip.portrange.reservedlow apply to IPv6 aswell as IPv4.
We could have made new sysctls for IPv6, but that potentially makes
things complicated for mapped addresses. This seems like the least
confusing option and least likely to cause obscure problems in the
future.
This change makes the mac_portacl module useful with IPv6 apps.
Reviewed by: ume
MFC after: 1 month
consumers ignore the return value, soabort() is required to succeed,
and protocols produce errors here to report multiple freeing of the
pcb, which we hope to eliminate.
right from the beginning and partly clean up the differences in handling
between SYN_SENT and SYN_RCVD (syncache).
Further changes to this code to come. This is a first incremental step
to a general overhaul and streamlining of the TCP code.
PR: kern/15095
PR: kern/92690 (partly)
Reviewed by: qingli (and tested with ANVL)
Sponsored by: TCP/IP Optimization Fundraise 2005
simultaneous open. Both the bug and the patch were verified using the
ANVL test suite.
PR: kern/74935
Submitted by: qingli (before I became committer)
Reviewed by: andre
MFC after: 5 days
threshold. Inflight doesn't make sense on a LAN as it has
trouble figuring out the maximal bandwidth because of the coarse
tick granularity.
The sysctl net.inet.tcp.inflight.rttthresh specifies the threshold
in milliseconds below which inflight will disengage. It defaults
to 10ms.
Tested by: Joao Barros <joao.barros-at-gmail.com>,
Rich Murphey <rich-at-whiteoaklabs.com>
Sponsored by: TCP/IP Optimization Fundraise 2005
it so that ip_id etc. don't get overwritten. This fixes forwarding
of fragmented IP packets through a dummynet pipe -- fragments came
out with modified and different(!) ip_id's, making it impossible to
reassemble a datagram at the receiver side.
Submitted by: Alexander Karptsov (reworked by me)
MFC after: 3 days
in syncache_lookup() is not cleared and may lead to an arbitrary and
bogus rtentry pointer which later gets free'd.
Reviewed by: andre
MFC after: 3 days
we have another PCB which is bound to 0.0.0.0. If a PCB has the
INP_IPV6 flag, then we set its cost higher than IPv4 only PCBs.
Submitted by: Keiichi SHIMA <keiichi__at__iijlab.net>
Obtained from: KAME
MFC after: 1 week
store some pipe pointers on stack. If user reconfigures dummynet
in the interlock gap, we can work with freed pipes after relock.
To fix this, we decided not to send packets in transmit_event(),
but fill a queue. At the end of dummynet() and dummynet_io(),
after the lock is dropped, if there is something in the queue
we run dummynet_send() to process the queue.
In collaboration with: ru
filtering mechanisms to use the new rwlock(9) locking API:
- Drop the variables stored in the phil_head structure which were specific to
conditions and the home rolled read/write locking mechanism.
- Drop some includes which were used for condition variables
- Drop the inline functions, and convert them to macros. Also, move these
macros into pfil.h
- Move pfil list locking macros intp phil.h as well
- Rename ph_busy_count to ph_nhooks. This variable will represent the number
of IN/OUT hooks registered with the pfil head structure
- Define PFIL_HOOKED macro which evaluates to true if there are any
hooks to be ran by pfil_run_hooks
- In the IP/IP6 stacks, change the ph_busy_count comparison to use the new
PFIL_HOOKED macro.
- Drop optimization in pfil_run_hooks which checks to see if there are any
hooks to be ran, and returns if not. This check is already performed by the
IP stacks when they call:
if (!PFIL_HOOKED(ph))
goto skip_hooks;
- Drop in assertion which makes sure that the number of hooks never drops
below 0 for good measure. This in theory should never happen, and if it
does than there are problems somewhere
- Drop special logic around PFIL_WAITOK because rw_wlock(9) does not sleep
- Drop variables which support home rolled read/write locking mechanism from
the IPFW firewall chain structure.
- Swap out the read/write firewall chain lock internal to use the rwlock(9)
API instead of our home rolled version
- Convert the inlined functions to macros
Reviewed by: mlaier, andre, glebius
Thanks to: jhb for the new locking API
and signifincantly improve the readability of ip_input() and
ip_output() again.
The resulting IPSEC hooks in ip_input() and ip_output() may be
used later on for making IPSEC loadable.
This move is mostly mechanical and should preserve current IPSEC
behaviour as-is. Nothing shall prevent improvements in the way
IPSEC interacts with the IPv4 stack.
Discussed with: bz, gnn, rwatson; (earlier version)
will be sent if there is an address on the bridge. Exclude the bridge from the
special arp handling.
This has been tested with all combinations of addresses on the bridge and members.
Pointed out by: Michal Mertl
however IPv4-in-IPv4 tunnels are now stable on SMP. Details:
- Add per-softc mutex.
- Hold the mutex on output.
The main problem was the rtentry, placed in softc. It could be
freed by ip_output(). Meanwhile, another thread being in
in_gif_output() can read and write this rtentry.
Reported by: many
Tested by: Alexander Shiryaev <aixp mail.ru>
ip_forward() would report back a zero MTU in ICMP needfrag messages
because on a IPSEC SP lookup failure no MTU got computed.
Fix this by changing the logic to compute a new MTU in any case if
IPSEC didn't do it.
Change MTU computation logic to use egress interface MTU if available
or the next smaller MTU compared to the current packet size instead
of falling back to a very small fixed MTU.
Fix associated comment.
PR: kern/91412
MFC after: 3 days
ia_hash only if it actually is an AF_INET address. All other places
test for sa_family == AF_INET but this one.
PR: kern/92091
Submitted by: Seth Kingsley <sethk-at-meowfishies.com>
MFC after: 3 days
If net.link.ether.inet.useloopback=1 and we send broadcast packet using our
own source ip address it may be rejected by uRPF rules.
Same bug was fixed for IPv6 in rev. 1.115 by suz.
PR: kern/76971
Approved by: glebius (mentor)
MFC after: 3 days
Vararg functions have a different calling convention than regular
functions on amd64. Casting a varag function to a regular one to
match the function pointer declaration will hide the varargs from
the caller and we will end up with an incorrectly setup stack.
Entirely remove the varargs from these functions and change the
functions to match the declaration of the function pointers.
Remove the now unnecessary casts.
Lots of explanations and help from: peter
Reviewed by: peter
PR: amd64/89261
MFC after: 6 days
errors from rn_inithead back to the ipfw initialization function.
- Check return value of rn_inithead for failure, if table allocation has
failed for any reason, free up any tables we have created and return ENOMEM
- In ipfw_init check the return value of init_tables and free up any mutexes or
UMA zones which may have been created.
- Assert that the supplied table is not NULL before attempting to dereference.
This fixes panics which were a result of invalid memory accesses due to failed
table allocation. This is an issue mainly because the R_Zalloc function is a
malloc(M_NOWAIT) wrapper, thus making it possible for allocations to fail.
Found by: Coverity Prevent (tm)
Coverity ID: CID79
MFC after: 1 week
This fixes a bug in the previous commit.
Found by: Coverity Prevent(tm)
Coverity ID: CID253
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
change the mbuf pointer and we don't have any way of passing
it back to the callers. Instead just fail silently without
updating the checksum but leaving the mbuf+chain intact.
A search in our GNATS database did not turn up any match for
the existing warning message when this case is encountered.
Found by: Coverity Prevent(tm)
Coverity ID: CID779
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
that currently can't be triggered. But better be safe than sorry
later on. Additionally it properly silences Coverity Prevent for
future tests.
Found by: Coverity Prevent(tm)
Coverity ID: CID802
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
route MTU.
This bug is very difficult to reach and not remotely exploitable.
Found by: Coverity Prevent(tm)
Coverity ID: CID162
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
may have changed by m_pullup() during fastforward processing.
While this is a bug it is actually never triggered in real world
situations and it is not remotely exploitable.
Found by: Coverity Prevent(tm)
Coverity ID: CID780
Sponsored by: TCP/IP Optimization Fundraise 2005
ipq_zone, to allocate fragment headers from, rather than using cast mbuf
storage. This was one of the few remaining uses of mbuf storage for
local data structures that relied on dtom(). Implement the resource
limit on ipq's using UMA zone limits, but preserve current sysctl
semantics using a sysctl proc.
MFC after: 3 weeks
Correct insecure temporary file usage in ee. [06:02]
Correct a race condition when setting file permissions, sanitize file
names by default, and fix a buffer overflow when handling files
larger than 4GB in cpio. [06:03]
Fix an error in the handling of IP fragments in ipfw which can cause
a kernel panic. [06:04]
Security: FreeBSD-SA-06:01.texindex
Security: FreeBSD-SA-06:02.ee
Security: FreeBSD-SA-06:03.cpio
Security: FreeBSD-SA-06:04.ipfw
interfaces to bridges, which will then send and receive IP protocol 97 packets.
Packets are Ethernet frames with an EtherIP header prepended.
Obtained from: NetBSD
MFC after: 2 weeks
action argument with the value obtained from table lookup. The feature
is now applicable only to "pipe", "queue", "divert", "tee", "netgraph"
and "ngtee" rules.
An example usage:
ipfw pipe 1000 config bw 1000Kbyte/s
ipfw pipe 4000 config bw 4000Kbyte/s
ipfw table 1 add x.x.x.x 1000
ipfw table 1 add x.x.x.y 4000
ipfw pipe tablearg ip from table(1) to any
In the example above the rule will throw different packets to different pipes.
TODO:
- Support "skipto" action, but without searching all rules.
- Improve parser, so that it warns about bad rules. These are:
- "tablearg" argument to action, but no "table" in the rule. All
traffic will be blocked.
- "tablearg" argument to action, but "table" searches for entry with
a specific value. All traffic will be blocked.
- "tablearg" argument to action, and two "table" looks - for src and
for dst. The last lookup will match.
of the radix lookup tables. Since several rnh_lookup() can run in
parallel on the same table, we can piggyback on the shared locking
provided by ipfw(4).
However, the single entry cache in the ip_fw_table can't be used lockless,
so it is removed. This pessimizes two cases: processing of bursts of similar
packets and matching one packet against the same table several times during
one ipfw_chk() lookup. To optimize the processing of similar packet bursts
administrator should use stateful firewall. To optimize the second problem
a solution will be provided soon.
Details:
o Since we piggyback on the ipfw(4) locking, and the latter is per-chain,
the tables are moved from the global declaration to the
struct ip_fw_chain.
o The struct ip_fw_table is shrunk to one entry and thus vanished.
o All table manipulating functions are extended to accept the struct
ip_fw_chain * argument.
o All table modifing functions use IPFW_WLOCK_ASSERT().
o Do not use ipfw_insn_pipe->pipe_ptr in locate_flowset(). The
_ipfw_insn_pipe isn't touched by this commit to preserve ABI
compatibility.
o To optimize the lookup of the pipe/flowset in locate_flowset()
introduce hashes for pipes and queues:
- To preserve ABI compatibility utilize the place of global list
pointer for SLIST_ENTRY.
- Introduce locate_flowset(queue nr) and locate_pipe(pipe nr).
o Rework all the dummynet code to deal with the hashes, not global
lists. Also did some style(9) changes in the code blocks that were
touched by this sweep:
- Be conservative about flowset and pipe variable names on stack,
use "fs" and "pipe" everywhere.
- Cleanup whitespaces.
- Sort variables.
- Give variables more meaningful names.
- Uppercase and dots in comments.
- ENOMEM when malloc(9) failed.
have any know to enable it from userland and could only be enabled by
either setting it to 1 at compile time or through the kernel debugger.
In the future it may be brought back as KTR tracing points.
Discussed with: rwatson
Sponsored by: TCP/IP Optimization Fundraise 2005
include ip_options.h into all files making use of IP Options functions.
From ip_input.c rev 1.306:
ip_dooptions(struct mbuf *m, int pass)
save_rte(m, option, dst)
ip_srcroute(m0)
ip_stripoptions(m, mopt)
From ip_output.c rev 1.249:
ip_insertoptions(m, opt, phlen)
ip_optcopy(ip, jp)
ip_pcbopts(struct inpcb *inp, int optname, struct mbuf *m)
No functional changes in this commit.
Discussed with: rwatson
Sponsored by: TCP/IP Optimization Fundraise 2005
have free space in it. Allocate correct mbuf from the beginning.
This allows icmp_error() to quote the entire TCP header in error
messages.
Sponsored by: TCP/IP Optimization Fundraise 2005
Prevent backup CARP hosts from replying to arp requests, fixes strangeness
with some layer-3 switches. From Bill Marquette.
Tested by: Kazuaki Oda <kaakun highway.ne.jp>
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
softc lists and associated mutex are now unused so these have been removed.
Calling if_clone_detach() will now destroy all the cloned interfaces for the
driver and in most cases is all thats needed to unload.
Idea by: brooks
Reviewed by: brooks
retransmitted without suppression, while there is demand for
such ARP entry. As before, retransmission is rate limited to
one packet per second. Details:
- Remove net.link.ether.inet.host_down_time
- Do not set/clear RTF_REJECT flag on route, to
avoid rt_check() returning error. We will generate error
ourselves.
- Return EWOULDBLOCK on first arp_maxtries failed
requests , and return EHOSTDOWN/EHOSTUNREACH
on further requests.
- Retransmit ARP request always, independently from return
code. Ratelimit to 1 pps.
Having an additional MT_HEADER mbuf type is superfluous and redundant
as nothing depends on it. It only adds a layer of confusion. The
distinction between header mbuf's and data mbuf's is solely done
through the m->m_flags M_PKTHDR flag.
Non-native code is not changed in this commit. For compatibility
MT_HEADER is mapped to MT_DATA.
Sponsored by: TCP/IP Optimization Fundraise 2005
