longer uses these interrupt vectors for its ISA interrupt pins, so these
entries will not be overwritten. If we get a spurious interrupt from the
ATPIC when using the APIC, it will be treated as a stray interrupt instead
of causing a panic.
- Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff
range. The pmap lazyfix IPI was reordered down next to the TLB
shootdowns to avoid conflicting with the spurious interrupt vector.
- Move the base of APIC interrupts up 16 so that the first 16 APIC
interrupts do not overlap the vectors used by the ATPIC.
- Remove bogus interrupt vector reservations for LINT[01].
- Now that 0xc0 - 0xef are available, use them for device interrupts.
This increases the number of APIC device interrupts to 191.
- Increase the system-wide number of global interrupts to 191 to catch up
to more APIC interrupts.
Requested by: peter (2)
vector stubs and into the C functions they call.
- Move disabling and EOIing of interrupt sources out of PIC driver entry
points and into intr_execute_handlers(). Intr_execute_handlers() only
disables a source for an interrupt if it is a stray interrupt or has
threaded handlers. Sources with fast handlers no longer disable (mask)
the source while executing the handlers.
- Move the setting of clkintr_pending into intr_execute_handlers() and set
the variable for any interrupt source with a vector of 0. (Should only
be true for IRQ 0.) This fixes clkintr_pending in the NO_MIXED_MODE
case.
- Implement lapic_eoi() and use it to implement ioapic_eoi_source().
- Rename atpic_sched_ithd() to atpic_handle_intr() since it is used to
handle all atpic interrupts and not just threaded ones.
Inspired by: peter's changes to amd64 in p4 (1)
Requested by: bde (2)
interrupt such as IRQ 22 or 19. However, the ACPI BIOS still routes
interrupts from some PCI devices to the same intpin calling the pin
IRQ 22. Thus, ACPI expects to address a single interrupt source via two
different names. To work around this, if the SCI is remapped to a non-ISA
interrupt (i.e., greater than 15), then we use
acpi_OverrideInterruptLevel() function to tell ACPI to use IRQ 22 or 19
rather than IRQ 9 for the SCI.
Previously we would change IRQ 22 or 19's name to IRQ 9 when we encountered
such an Interrupt Source Override entry in the MADT which routed the SCI
properly but left PCI devices mapped to IRQ 22 or 19 w/o a routable
interrupt.
Tested by: sos
should now only have HTT CPUs if they have explicitly asked for them
either by enabling HyperThreading in the BIOS or by using the
MPTABLE_FORCE_HTT kernel option.
should only be used if they are enabled in the BIOS. Now that we support
enumerating CPUs using the ACPI MADT, any HTT machine using ACPI should
respect the BIOS setting. For HTT machines with ACPI disabled in the
kernel, the MPTABLE_FORCE_HTT kernel option can be used to try to probe HTT
CPUs like have done in the past for the MP Table case. This option should
only be enabled if HTT is enabled in the BIOS.
Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
is highly MD in an emulation environment since it operates on the host
environment. Although the setregs functions are really for exec support
rather than signals, they deal with the same sorts of context and include
files. So I put it there rather than create yet another file.
pin that is used by the default identity mapping if it still maps to the
old vector. The ACPI case might need some tweaking for the SCI interrupt
case since ACPI likes to address the intpin using both the IRQ remapped to
it as well as the previous existing PCI IRQ mapped to it.
Reported by: kan
rather than signed. This fixes some cosmetics such as verbose printf's
for IRQs greater than 127.
- The calculation for next_ioapic_base was also adjusted so that it will
only complain once for each hole in the IRQs provided by ACPI for IO
APICs.
Reported by: Michal Mertl <mime@traveller.cz>
- The MP code no longer knows anything specific about an MP Table.
Instead, the local APIC code adds CPUs via the cpu_add() function when
a local APIC is enumerated by an APIC enumerator.
- Don't divide the argument to mp_bootaddress() by 1024 just so that we
can turn around and mulitply it by 1024 again.
- We no longer panic if SMP is enabled but we are booted on a UP machine.
- init_secondary(), the asm code between init_secondary() and ap_init()
in mpboot.s and ap_init() have all been merged together in C into
init_secondary().
- We now use the cpuid feature bits to determine if we should enable
PSE, PGE, or VME on each AP.
- Due to the change in the implementation of critical sections, acquire
the SMP TLB mutex around a slightly larger chunk of code for TLB
shootdowns.
- Remove some of the debug code from the original SMP implementation
that is no longer used or no longer applies to the new APIC code.
- Use a temporary hack to disable the ACPI module until the SMP code has
been further reorganized to allow ACPI to work as a module again.
- Add a DDB command to dump the interesting contents of the IDT.
devices claiming resources that they don't actually use. The PIC drivers
only register valid interrupt sources, so we don't need to rely on these
drivers to claim invalid IRQs to prevent their use by other drivers.
APIC Descriptor Table to enumerate both I/O APICs and local APICs. ACPI
does not embed PCI interrupt routing information in the MADT like the MP
Table does. Instead, ACPI stores the PCI interrupt routing information
in the _PRT object under each PCI bus device. The MADT table simply
provides hints about which interrupt vectors map to which I/O APICs. Thus
when using ACPI, the existing ACPI PCI bridge drivers are sufficient to
route PCI interrupts.
- The apic interrupt entry points have been rewritten so that each entry
point can serve 32 different vectors. When the entry is executed, it
uses one of the 32-bit ISR registers to determine which vector in its
assigned range was triggered. Thus, the apic code can support 159
different interrupt vectors with only 5 entry points.
- We now always to disable the local APIC to work around an errata in
certain PPros and then re-enable it again if we decide to use the APICs
to route interrupts.
- We no longer map IO APICs or local APICs using special page table
entries. Instead, we just use pmap_mapdev(). We also no longer
export the virtual address of the local APIC as a global symbol to
the rest of the system, but only in local_apic.c. To aid this, the
APIC ID of each CPU is exported as a per-CPU variable.
- Interrupt sources are provided for each intpin on each IO APIC.
Currently, each source is given a unique interrupt vector meaning that
PCI interrupts are not shared on most machines with an I/O APIC.
That mapping for interrupt sources to interrupt vectors is up to the
APIC enumerator driver however.
- We no longer probe to see if we need to use mixed mode to route IRQ 0,
instead we always use mixed mode to route IRQ 0 for now. This can be
disabled via the 'NO_MIXED_MODE' kernel option.
- The npx(4) driver now always probes to see if a built-in FPU is present
since this test can now be performed with the new APIC code. However,
an SMP kernel will panic if there is more than one CPU and a built-in
FPU is not found.
- PCI interrupts are now properly routed when using APICs to route
interrupts, so remove the hack to psuedo-route interrupts when the
intpin register was read.
- The apic.h header was moved to apicreg.h and a new apicvar.h header
that declares the APIs used by the new APIC code was added.
default we provide 16 interrupt sources for IRQs 0 through 15. However,
if the I/O APIC driver has already registered sources for any of those IRQs
then we will silently fail to register our own source for that IRQ.
Note that i386/isa/icu.h is now specific to the 8259A and no longer
contains any info relevant to APICs. Also note that fast interrupts no
longer use a separate entry point. Instead, both fast and threaded
interrupts share the same entry point which merely looks up the appropriate
source and passes control to intr_execute_handlers().
that provides methods via a PIC driver to do things like mask a source,
unmask a source, enable it when the first interrupt handler is added, etc.
The interrupt code provides a table of interrupt sources indexed by IRQ
numbers, or vectors. These vectors are what new-bus uses for its IRQ
resources and for bus_setup_intr()/bus_teardown_intr(). The interrupt
code then maps that vector a given interrupt source object. When an
interrupt comes in, the low-level interrupt code looks up the interrupt
source for the source that triggered the interrupt and hands it off to
this code to execute the appropriate handlers.
By having an interrupt source abstraction, this allows us to have different
types of interrupt source providers within the shared IRQ address space.
For example, IRQ 0 may map to pin 0 of the master 8259A PIC, IRQs 1
through 60 may map to pins on various I/O APICs, and IRQs 120 through
128 may map to MSI interrupts for various PCI devices.
