implementation of heartbeat interval was 2 but there was typo which
caused the heartbeat is sent approximately every 5 seconds. This
caused unintended controller reset by firmware because firmware
thought OS was crashed.
Submitted by: Floris Bos < info <> je-eigen-domein dot nl >
Tested by: Andrzej Tobola < ato <> iem dot pw dot edu dot pl >
chains. This part of code is to enhance performance so failing the
collapsing should not free TX frames. Otherwise bge(4) will
unnecessarily drop frames which in turn can freeze the network
connection.
Reported by: Igor Sysoev (is <> rambler-co dot ru)
Tested by: Igor Sysoev (is <> rambler-co dot ru)
over GMII, make sure to enable GMII. With this change brgphy(4) is
used to handle the dual mode PHY. Since we still don't have a sane
way to pass PHY specific information to mii(4) layer special
handling is needed in brgphy(4) to determine which mode of PHY was
configured in parent interface.
This change make BCM5715S work.
Tested by: olli
Obtained from: OpenBSD
MFC after: 1 week
o Don't enable BGE_FLAG_BER_BUG on both 5722 and 5756, and based
on their PCI IDs rather than their chip IDs.
Reported by: several PC-BSD users via kmoore
Reviewed by: yongari, imp, jhb, davidch
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
same ASIC ID of BCM5758 such that r198318 incorecctly enabled TSO
on BCM5754.BCM5754M controllers. BCM5754/BCM5754M needs a special
firmware to enable TSO and bge(4) does not support firmware based
TSO.
Reported by: ed
Tested by: ed
hw.bge.forced_collapse. hw.bge.forced_collapse affects all bge(4)
controllers on system which may not desirable behavior of the
sysctl node. Also allow the sysctl node could be modified at any
time.
Reviewed by: bde (initial version)
feature. These registers are reserved on controllers that have no
support for jumbo frame.
Only BCM5700 has mini ring so do not poke mini ring related
registers if controller is not BCM5700.
Reviewed by: marius
handler in brgphy(4) does not exist and brgphy(4) just resets the
PHY and returns EINVAL as it has no isolation handler. I also agree
on Marius's opinion that stop handler of every NIC driver seems to
be the wrong place for implementing PHY isolate/power down.
If we need PHY isolate/power down it should be implemented in
brgphy(4) and users should administratively down the PHY.
Reviewed by: marius
single outstanding DMA read operation. Most controllers targeted to
client with PCIe bus interface(e.g. BCM5761) may have this
limitation. All controllers for servers does not have this
limitation.
Collapsing mbuf chains to reduce number of memory reads before
transmitting was most effective way to workaround this. I got about
940Mbps from 850Mbps with mbuf collapsing on BCM5761. However it
takes a lot of CPU cycles to collapse mbuf chains so add tunable to
control the number of allowed TX buffers before collapsing. The
default value is 0 which effectively disables the forced collapsing.
For most cases 2 would yield best performance(about 930Mbps)
without much sacrificing CPU cycles.
Note the collapsing is only activated when the controller is on
PCIe bus and the frame does not need TSO operation. TSO does not
seem to suffer from the hardware limitation because the payload
size is much bigger than normal IP datagram.
Thanks to davidch@ who told me the limitation of client controllers
and actually gave possible workarounds to mitigate the limitation.
Reviewed by: davidch, marius
Tx/Rx/Rx return ring such that large part of status block was not
used at all. All bge(4) controllers except BCM5700 AX/BX has a
feature to control the size of status block. So use minimum status
block size allowed in controller. This reduces number of DMAed
status block size to 32 bytes from 80 bytes.
seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
Tested by: current
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
Reviewed by: davidch
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
update and then clear status block. Previously it used to access
these index without synchronization which may cause problems when
bounce buffers are used. Also add missing bus_dmamap_sync(9) in
polling handler. Since we now update status block in driver, adjust
bus_dmamap_sync(9) for status block.
checking IFF_DRV_RUNNING and IFF_DRV_OACTIVE flags. Also if we
have less than 16 free send BDs set IFF_DRV_OACTIVE and try it
later. Previously bge(4) used to reserve 16 free send BDs after
loading dma maps but hardware just need one reserved send BD. If
prouder index has the same value of consumer index it means the Tx
queue is empty.
While I'm here check IFQ_DRV_IS_EMPTY first to save one lock
operation.
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
Reviewed by: marius
Revision 1.158 says only lower ten bits of
BGE_RXLP_LOCSTAT_IFIN_DROPS register is valid. For BCM5761 case it
seems the controller maintains 16bits value for the register.
However 16bits are still too small to count all dropped packets
happened in a second. To get a correct counter we have to read the
register in bge_rxeof() which would be too expensive.
Pointed out by: bde
MAC in bge_tick. Previously it used to show more number of input
errors. I noticed actual input errors were less than 8% even for
64 bytes UDP frames generated by netperf.
Since we always access BGE_RXLP_LOCSTAT_IFIN_DROPS register in
bge_tick, remove useless code protected by #ifdef notyet.
initializes it to ETHER_HDR_LEN so we have to override it after
calling ether_ifattch().
While I'm here remove setting if_mtu value, it's initialized in
ether_ifattach().
Introduce two spare dma maps for standard buffer and jumbo buffer
respectively. If loading a dma map failed reuse previously loaded
dma map. This should fix unloaded dma map is used in case of dma
map load failure. Also don't blindly unload dma map and defer
dma map sync and unloading operation until we know dma map for new
buffer is successfully loaded. This change saves unnecessary dma
load/unload operation. Previously bge(4) tried to reuse mbuf
with unloaded dma map which is really bad thing in bus_dma(9)
perspective.
While I'm here update if_iqdrops if we can't allocate Rx buffers.
standard buffer size. If controller is not capable of handling
jumbo frame, interface MTU couldn't be larger than standard MTU
which in turn the received should be fit in standard buffer. This
fixes bus_dmamap_sync call for jumbo ring is called even if
interface is configured to use standard MTU.
Also if total frame size could be fit into standard buffer don't
use jumbo buffers.
for buffer allocation. If driver know we are out of Rx buffers let
controller stop. This should fix panic when interface is run even
if it had no configured Rx buffers.
and Rx DMA tag separately. Previously it used a common mbuf DMA tag
for both Tx and Rx path but Rx buffer(standard ring case) should
have a single DMA segment and maximum buffer size of the segment
should be less than or equal to MCLBYTES. This change also make it
possible to add TSO with minor changes.
bge_newbuf_std still has a bug for handling dma map load failure
under high network load. Just reusing mbuf is not enough as driver
already unloaded the dma map of the mbuf. Graceful recovery needs
more work.
Ideally we can just update dma address part of a Rx descriptor
because the controller never overwrite the Rx descriptor. This
requires some Rx initialization code changes and it would be done
later after fixing other incorrect bus_dma(9) usages.
instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Synchronize RX return ring memory in rx_eof. This is needed
as the deviced updates this memory when receives packets.
- Decouple the synchronization of BGE status block in the interrupt
service routine: perfrom PREREAD synchronization only all accesses
to this block are finished. This seems to be more natural.
Reviewed by: yongari, marius
MFC after: 2 weeks
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Reported by: erwin
Hardware provided by: TDC A/S
Reviewed by: stas
Tested by: stas
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
loop iteration as it can be updated by the card while we
process the RX ring forcing us to process RX descriptors
for which DMA synchronisation operation has not been
performed. This fixes the bug when bge(4) drops packets
under high load.
Discussed with: yongari, marius
Approved by: re (kib)
MFC after: 1 week
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
