DragonFlyBSD, so it certainly doesn't need splsoftvm(). Remove it.
# I doubt this driver will now compile on older FreeBSD versions or DFBSD
# We should consider unifdefing it since that code seems unmaintained.
Specifcially, in_cksum_hdr() returns 0 (not 0xffff) when the IPv4
checksum is correct. Without this fix, the tcp_lro code will reject
good IPv4 traffic from drivers that do not implement IPv4 header
harder csum offload.
Sponsored by: Myricom Inc.
MFC after: 7 days
this code to depessimize the worst case we've lived with silently and
uneventfully for the past 12 years. Add a comment about a refinement
for those needing more assurance of accuracy.
Fix ddb's show rtc command deadlock potential when debugging rtc code
by not taking the lock if we're in the debugger. If you need a thumb
to count the number of people that have encountered this, I'd be
surprised.
Submitted by: bde
Specifically - never jack the TX FIFO threshold up to the absolute
maximum; always leave enough space for two DMA transactions to
appear.
This is a paranoia from the Linux ath9k driver. It can't hurt.
Obtained from: Linux ath9k
libraries it calls (although some might not be doing it right). We are
serialized right now by giant as well. This means the splsoftclock are
now an anachronism that has no benefit, even marking where locking
needs to happen. Remove them.
The default is to limit them to what the hardware is capable of.
Add sysctl twiddles for both the non-RTS and RTS protected aggregate
generation.
Whilst here, add some comments about stuff that I've discovered during
my exploration of the TX aggregate / delimiter setup path from the
reference driver.
- bear with me, there are lots of white space changes, I would not
do them, but I am a mere consumer of this stuff and if these drivers
are to stay in shape they need to be taken.
em driver changes: support for the new i217/i218 interfaces
igb driver changes:
- TX mq start has a quick turnaround to the stack
- Link/media handling improvement
- When link status changes happen the current flow control state
will now be displayed.
- A few white space/style changes.
lem driver changes:
- the shared code uncovered a bogus write to the RLPML register
(which does not exist in this hardware) in the vlan code,this
is removed.
CSUM_TCP too. They are all set explicitly by the kernel usually.
While here, fix an unrelated bug where hardware L4 checksum calculation
was accidentally disabled for some IPv6 packets.
Reported by: alfred@
MFC after: 3 days
process that has crashed.
sys/cddl/contrib/opensolaris/uts/common/dtrace/fasttrap.c:
In fasttrap_pid_disable(), we cannot PHOLD the proc
structure for a process that no longer exists, but
we still have other, fasttrap specific, state that
must be cleaned up for probes that existed in the
dead process. Instead of returning early if the
process related to our probes isn't found,
conditionalize the locking and carry on with a NULL
proc pointer. The rest of the fasttrap code already
understands that a NULL proc is possible and does
the right things in this case.
Sponsored by: Spectra Logic Corporation
Reviewed by: rpaulo, gnn
MFC after: 1 week
machine/signal.h and machine/ucontext.h into common x86 includes,
copying from amd64 and merging with i386.
Kernel-only compat definitions are kept in the i386/include/sigframe.h
and i386/include/signal.h, to reduce amd64 kernel namespace pollution.
The amd64 compat uses its own definitions so far.
The _MACHINE_ELF_WANT_32BIT definition is to allow the
sys/boot/userboot/userboot/elf32_freebsd.c to use i386 ELF definitions
on the amd64 compile host. The same hack could be usefully abused by
other code too.
When initializing the fdt, query U-Boot as well.
With this change, it is now feasible to have U-Boot load
the FDT, ubldr will pull it from U-Boot and hand it to the
kernel.
- fix indentation
- put the operator at the end of the line for long statements
- remove spaces between the type and the variable in a cast
- remove excessive parentheses
Tested by: md5
This has reduced the number of TX delimiter and data underruns when
doing large UDP transfers (>100mbit).
This stops any HAL_INT_TXURN interrupts from occuring, which is a good
sign!
Obtained from: Qualcomm Atheros
* Delete this debugging print - I used it when debugging the initial
TX descriptor chaining code. It now works, so let's toss it.
It just confuses people if they enable TX descriptor debugging as they
get two slightly different versions of the same descriptor.
* Indenting.
part of ts_status. Thus:
* make sure we decode them from ts_flags, rather than ts_status;
* make sure we decode them regardless of whether there's an error or not.
This correctly exposes descriptor configuration errors, TX delimiter
underruns and TX data underruns.
seems to cause more problems then previous behavior: it either breaks
initilization sequence in other places or uncovers problems with
high-speed mode timing for SDHCI 3.0
Make dcons input polling adaptive, reducing poll rate to 1Hz after several
minutes of inactivty to reduce global interrupt rate. Most of users never
used FireWire debugging, so it is not very useful to consume power by it.
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
