interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
is the actual name here) on EBus and which are PCF8584 (on systems having
a boot-bus controller the i2c are said to not be a PCF8584). Similar to the
SUNW,envctrl devices, onboard slaves for monitoring fans, temperatures and
such hang off of these i2c devices. But there's also stuff like EEPROMs
housing the hostid of the system and the boards usally have a connector to
add custom slave devices (on CP1500 there's actually a second PCF8584 with
its own I2C bus for these).
This driver already works fine but I'm not yet sure if access to the slave
devices on CP1400/CP1500 marked as "reserved for factory use" in the docs
should be blocked (most likely these are the voltage controllers wich aren't
meant to be controller by software and even not by the firmware). Once the
issues with polled mode are fixed in the common pcf(4) part in pcf.c, this
front-end should probably honour the poll-mode property of the i2c devices.
Tested on Ultra AXe and CP1500 (Netra t1 100).
OK'ed by: joerg, nsouch
