The latest imported FDT data defines a node for an iomuxc-gpr device,
which we don't support (or need, right now) in addition to the usual
iomuxc device. Unfortunately, the dts improperly assigns overlapping
ranges of mmio space to both devices. The -gpr device is also a syscon
and simple_mfd device.
At runtime the simple_mfd driver attaches for the iomuxc-gpr node, then
when the real iomuxc driver comes along later, it fails to attach because
it tries to allocate its register space, and it's already partially in
use by the bogus instance of simple_mfd.
This change works around the problem by simply disabling the node for
the iomuxc-gpr device, since we don't need it for anything.
NANDFS has been broken for years. Remove it. The NAND drivers that
remain are for ancient parts that are no longer relevant. They are
polled, have terrible performance and just for ancient arm
hardware. NAND parts have evolved significantly from this early work
and little to none of it would be relevant should someone need to
update to support raw nand. This code has been off by default for
years and has violated the vnode protocol leading to panics since it
was committed.
Numerous posts to arch@ and other locations have found no actual users
for this software.
Relnotes: Yes
No Objection From: arch@
Differential Revision: https://reviews.freebsd.org/D20745
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
r306041 changed ld invocations for converting binary files to kernel
ELF objects to pass -m, but missed bespoke ld invocations in a pair of
arm file configs (one of which has since been removed).
This is needed to support some external toolchains and lld.
Sponsored by: The FreeBSD Foundation
error in the function hypercall_memfree(), where the wrong arena was being
passed to kmem_free().
Introduce a per-page flag, VPO_KMEM_EXEC, to mark physical pages that are
mapped in kmem with execute permissions. Use this flag to determine which
arena the kmem virtual addresses are returned to.
Eliminate UMA_SLAB_KRWX. The introduction of VPO_KMEM_EXEC makes it
redundant.
Update the nearby comment for UMA_SLAB_KERNEL.
Reviewed by: kib, markj
Discussed with: jeff
Approved by: re (marius)
Differential Revision: https://reviews.freebsd.org/D16845
In the armv4/5 world device statements in these files were common, but in
the v6/7 world, other socs don't put device statements into those files, so
this just brings imx5 and imx6 into line with the current conventions.
ignore the timestamp passed in to settime() due to inaccuracy, the core
routines now pass in a nanosecond-accurate time freshly-obtained before
calling each driver's settime() method. Also, add calls to the new
debugging output helpers.
automatically initializing the watchdog using the given value. Also,
attach at BUS_PASS_TIMER to extend watchdog protection to more of the
kernel init process.
The correct value is seconds*2-1. The code was using just seconds*2, which
led to being off by a half-second -- usually not a big deal, except when the
value was the max (128) it overflowed so zero would get written to the
countdown register, which equates to a timeout of a half second.
detach() to do nothing if attach() succeeded, which is the opposite of
what's needed. Also, move device_delete_children() from the end to the
beginning of detach(), so that children won't be trying to make use of the
hardware we're in the process of shutting down.
PR: 229510
arrays, as elements 0 and 1 of one array and elements 1 and 2 of the other.
Run the loop 0..1 instead of 1..2 and use named constants to offset into
one of the arrays.
PR: 229508
a gpio pin. If neither of the options is specified, pre-set the pin's
output value to the pin's current input value, to achieve glitch-free
transitions to output mode on pins that are pulled up or down at reset
or via fdt pinctrl data.
mode or not. An earlier attempt to make this work was done in r320456, by
always reading the pad status register (PSR) instead of the data register.
But it turns out the values in PSR only reflect the electrical level of an
output pin if the pad is configured with the SION (Set Input On) bit in the
pinmux config, and most output gpio pads are not configured that way.
So now a gpio read is done by returning the value from the data register,
which works right whether the pin is configured for input or output, unless
the pin has been set for OPENDRAIN mode, in which case the PSR is read
instead. For this to work, the pin must also be configured with SION turned
on in the fdt pinmux data, which is a reasonable thing to require for the
unusual case of reading an open-drain output pin.
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
Name each ahci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ahci from kernel; already loaded from kernel
Change OF_getencprop_alloc semantics to be combination of malloc and
OF_getencprop and return size of the property, not number of elements
allocated.
For the use cases where number of elements is preferred introduce
OF_getencprop_alloc_multi helper function that copies semantics
of OF_getencprop_alloc prior to this change.
This is to make OF_getencprop_alloc and OF_getencprop_alloc_multi
function signatures consistent with OF_getencprop_alloc and
OF_getencprop_alloc_multi.
Functionality-wise this patch is mostly rename of OF_getencprop_alloc
to OF_getencprop_alloc_multi except two calls in ofw_bus_setup_iinfo
where 1 was used as a block size.
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
OF_finddevices returns ((phandle_t)-1) in case of failure. Some code
in existing drivers checked return value to be equal to 0 or
less/equal to 0 which is also wrong because phandle_t is unsigned
type. Most of these checks were for negative cases that were never
triggered so trhere was no impact on functionality.
Reviewed by: nwhitehorn
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14645
Pretty much any other device might need to manipulate a gpio pin during its
probe or attach routines, so these devices must be available as early as
possible.
The gpio device is an interrupt controller, but I didn't choose the
INTERRUPT pass for that reason (it works fine as an interrupt controller as
long as it attaches any time before interrupts are enabled). That just
looked like the right place in the passes to ensure that it attaches before
any type of device that might need gpio pin manipulations.
driver requires interrupts to do transfers, and the drivers for the SPI
devices on the bus quite reasonably expect to be able to do IO while probing
and attaching.
appears that node names no longer include leading zeroes in the @address
qualifiers, so we have to search for the nodes involved in interrupt fixup
using both flavors of name to be compatible with old and new .dtb files.
(You know you're in a bad place when you're applying a workaround to code
that exists only as a workaround for another problem.)
the "power down" watchdog used by the ROM boot code is still active when the
regular watchdog is activated, turn off the power-down watchdog.
This adds support for the "fsl,ext-reset-output" FDT property. When
present, that property indicates that a chip reset is accomplished by
asserting the WDOG1_B external signal, which is supposed to trigger some
external component such as a PMIC to ready the hardware for reset (for
example, adjusting voltages from idle to full-power levels), and assert the
POR signal to SoC when ready. To guard against misconfiguation leading to a
non-rebootable system, the external reset signal is backstopped by code
that asserts a normal internal chip reset if nothing responds to the
external reset signal within one second.
bottom of the file, where it is in most imx5/6 drivers. Switch from an RD2
macro using bus_space_read_2() to an inline function using bus_read_2();
likewise for WR2. Use RESOURCE_SPEC_END to end the resource_spec list.
Net effect should be no functional changes.
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
