For now, preserve the gif_called functionality to limit the nesting
level because uncontrolled nesting can easily cause the kernel stack
exhaustion. Rumors are it should be shot to allow people to easily
shoot themselves in the foot, but I have ran out of cartridges. ;)
(when new natd is started before old natd died) and allows to manage natd
without touching ipfw.
natd should probably be killed with SIGKILL when stopping natd.
- Use sendmail_foo variables after load_rc_config so that they actually work.
- Utilize sendmail_procname.
- Check sendmail_submit_enable instead of sendmail_enable when dealing
with mail submission MTA.
case we should wait for the resetdone handler to be called before
returning.
- When providing resources via ndis_query_resources(), uses the
computed rsclen when using bcopy() to copy out the resource data
rather than the caller-supplied buffer length.
- Avoid using ndis_reset_nic() in if_ndis.c unless we really need
to reset the NIC because of a problem.
- Allow interrupts to be fielded during ndis_attach(), at least
as far as allowing ndis_isr() and ndis_intrhand() to run.
- Use ndis_80211_rates_ex when probing for supported rates. Technically,
this isn't supposed to work since, although Microsoft added the extended
rate structure with the NDIS 5.1 update, the spec still says that
the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of
this, it appears some drivers use it anyway.
- When adding in our guessed rates, check to see if they already exist
so that we avoid any duplicates.
- Add a printf() to ndis_open_file() that alerts the user when a
driver attempts to open a file under /compat/ndis.
With these changes, I can get the driver for the SMC 2802W 54g PCI
card to load and run. This board uses a Prism54G chip. Note that in
order for this driver to work, you must place the supplied smc2802w.arm
firmware image under /compat/ndis. (The firmware is not resident on
the device.)
Note that this should also allow the 3Com 3CRWE154G72 card to work
as well; as far as I can tell, these cards also use a Prism54G chip.
without the (defunct) isa compatibility shims. The new-bus-specific
parts are very similar to the ones for the pci probe and attach.
This was held up too long waiting for a repo copy to src/sys/dev/cy,
so I decided to fix the files in their old place. This gives easier
to read and merge diffs anyway.
The "count" line in src/sys/conf/files won't be changed until after
the repo copy, so old kernel configs that specify a count need not be
(and must not be) changed until then. The count is just ignored in
the driver. One unfinished detail is dynamic allocation of arrays
with <count> and (<count> * 32) entries, and iteration over the arrays.
This is now kludged with a fixed count of 10 (up to 10 cards with up
to 32 ports each).
Prodded by: imp
Submitted by: mostly by imp
Approved by: imp
common attach function so that the lock gets initialized in all cases.
This fixes breakage of the initialization of the lock in the pci case
in rev.1.135 (between the releases of 5.1 and 5.2). The lock is only
used in the SMP case, so this bug was not always fatal.
vm_mmap_vnode function, where we can safely check for a special /dev/zero
case. Rev. 1.180 has reordered checks and introduced a regression.
Submitted by: alc
Was broken by: kan
and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
It was fixed by moving problemetic checks, as well as checks that
doesn't need locking before locks are acquired.
Submitted by: Ryan Sommers <ryans@gamersimpact.com>
In co-operation with: cperciva, maxim, mlaier, sam
Tested by: submitter (previous patch), me (current patch)
Reviewed by: cperciva, mlaier (previous patch), sam (current patch)
Approved by: sam
Dedicated to: enough!
SCHED_INTERACT_MAX was used where SCHED_SLP_RUN_MAX was needed. This was
causing the interactivity scaler to lose history at a more dramatic rate
than intended.
scenario into #ifdef DEBUG. This makes my cluster with Belkin
KVM switch completely usable, even if the KVM switch and mouse
get a bit confused sometimes.
Without this, when the mouse gets confused, all sorts of crud
gets spammed all over the screen. With this, the mouse may appear
dead for a second or three, but it recovers silently.
Now, if we have for example: ad0s1 ad0s1c ad2s1 ad2s1c and we will try
to do: gconcat label foo /dev/ad0s1 /dev/ad2s1 we'll get a panic:
panic: spoiled but dcr = 1
for inside of geom_slice class, backtrace shows:
g_access()
g_slice_access()
g_access()
g_concat_read_metadata()
We need to get a proper fix for this race before geom(8) will be committed.
phandle_t. Since both are typedefed to unsigned int, this is more
or less cosmetic.
- Fix the code that determines whether a creator instance was used
for firmware output (and should not be blanked on initialization).
Since r1.2 of dev/fb/creator.c, this consisted comparing a handle of
an instance of a package with a handle of the package itself.
Use the test from r1.1, which utilizes OF_instance_to_package().
Submitted by: Marius Strobl <marius@alchemy.franken.de>
