- Add conversions to/from little endian for fields that the NIC accesses
by DMA as required.
- Add some bus_dmamap_sync() calls, and correct some existing ones.
- Read the receiver information from the EEPROM in an endian-neutral
manner.
- Load all RX and TX descriptors in a single DMA map up front, and
get the bus addresses of individual descriptors by address arithmetic;
this fixes multiple use of the descriptor tags, which would have
undesired effects.
It seems that xl still does not work on e250 boxen, for reasons which
are not clear yet.
Reviewed by: mux
is read one clock edge too late. This bit is driven low by
slave (as any other input data bits from slave) when the clock
is LOW. The current code did read the bit after the clock was
driven high again.
Reviewed by: luoqi
MFC after: 2 weeks
bus_dmamap_load_mbuf() returned EFBIG.
o Fix mbuf leaks in an error (rare) code path.
o Reuse the TX descriptor if xl_encap() failed instead of
just picking the next one.
o Better error messages.
it possible to use this driver under ia64, sparc64 (though
there may be endianness issues with this one) and other archs.
Tested on: i386, alpha (gallatin)
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
According to the MII specification, the delay produced by our
reads alone are sufficient for correct operation.
This reduces the time mii_tick takes from 10ms to ~1ms here. That's
still a lot, but much better than before.
Submitted by: Harti Brandt <brandt@fokus.gmd.de>
MFC after: 3 weeks
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
a major slowdown, and re-enable stats overflow interrupts.
For future reference, the bug was in our code, and not
some bug in the 3com chips.
Reviewed by: wpaul
MFC after: 2 days
dual function card. It needs pretty much the same flags as the 656C,
except that it seems to need both the INVERT_MII_PWR and INVERT_LED_PWR
flags set. Tested with cardbus in -current as of today.
Also added support for the 3c656, which looks to be the same as
the 656B, except it doesn't need the EEPROM_8BIT flag. I think. This
one is untested, but the added support should not break any of the
other cards.
never completed" message. The RX reset takes longer complete than it
used to, a lot longer in fact than xl_wait() is prepared to wait.
When we do the RX reset in xl_reset(), this cases xl_wait() to time out
and whine. We wait a little extra time now after the RX reset, which
should silence the warning.
Thanks to obrien for finally getting me a box with a NIC that
causes this problem for me to tinker with.
setting the 'max packet size' register in window 3. This only
works for cards based on the cyclone or newer chipsets (i.e. it
won't work with the original 3c905/boomerang cards).
There is a trick which will work with the boomerang, which is to turn
on the 'large packets ok' bit in the MAC control register, however this
lets the chip accept any frame up to 4K in length, which is larger than
the mbuf cluster buffers we use to receive frames. If somebody sends us
such a frame and the chip DMAs it to us, it could write past the end
of the cluster buffer and clobber something.
PR: kern/27742
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.
I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
rather than all the flags. This prevents setting being read from ROM,
which is a problem. If this breaks anything, it will only break the
3C556B cards minipci cards, which mainly exist at rpi as far as rpi
has been able to tell.
Submitted by: Louis Gerbarg <gerbal@rpi.edu>
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
laptops. I've checked that this still works with the other cards and
it works with the 3c556 that I have access to, but I want to check that
it works with the 556B mentioned in PR #20878 before I close out the PR
and merge to -stable.
