the target mode code or outer layers.
Increase cd_tagval to be 32 bits since it will have to now carry 16
bits of parallel SCSI ATIO handle as well as a normal tag (if any).
Solaris (which, for reasons unknown to me, chokes on u_int16_t
as a typedef of unsigned short if used in a transitional (mixed K&R
and ANSI) way), we'll go the extra mile and fully ANSIfy things.
offset is set to 0.
Re-arrange the DT limiting code so that we don't end up setting the period
to 0xa if the user really wants async. The previous behavior seemed to
confuse the aic(4) driver.
PR: kern/22733
Reviewed by: gibbs
devices. opening /dev/{dsp,dspW,audio}0 and then opening a different device
from that list and closing it resulted in a panic when any operation is
performed on the first fd.
we prevent this happening by denying the second open unless it uses the same
minor device as the first.
PR: kern/25519
is transmitted as all ones". This got broken after introduction
of delayed checksums as follows. Some guys (including Jonathan)
think that it is allowed to transmit all ones in place of a zero
checksum for TCP the same way as for UDP. (The discussion still
takes place on -net.) Thus, the 0 -> 0xffff checksum fixup was
first moved from udp_output() (see udp_usrreq.c, 1.64 -> 1.65)
to in_cksum_skip() (see sys/i386/i386/in_cksum.c, 1.17 -> 1.18,
INVERT expression). Besides that I disagree that it is valid for
TCP, there was no real problem until in_cksum.c,v 1.20, where the
in_cksum() was made just a special version of in_cksum_skip().
The side effect was that now every incoming IP datagram failed to
pass the checksum test (in_cksum() returned 0xffff when it should
actually return zero). It was fixed next day in revision 1.21,
by removing the INVERT expression. The latter also broke the
0 -> 0xffff fixup for UDP checksums.
Before this change:
: tcpdump: listening on lo0
: 127.0.0.1.33005 > 127.0.0.1.33006: udp 0 (ttl 64, id 1)
: 4500 001c 0001 0000 4011 7cce 7f00 0001
: 7f00 0001 80ed 80ee 0008 0000
After this change:
: tcpdump: listening on lo0
: 127.0.0.1.33005 > 127.0.0.1.33006: udp 0 (ttl 64, id 1)
: 4500 001c 0001 0000 4011 7cce 7f00 0001
: 7f00 0001 80ed 80ee 0008 ffff
each node in order to make it easier to add new entries.
Rewrite the internal directory structure so that it is possible to
have independent subdirectories. Utilize this to add /proc/net/dev.
Reviewed by: DES
Paste always happens to current _text_ cursor position independently of
mouse cursor position in any case and old variant force user to press
mouse paste button _two_ times if mouse cursor is invisible.
to call fork1() directly if we don't want out process queued right away.
This has the serendipitous side effect of saving us a call to pfind().
This makes threaded Linux apps (such as Opera) work again.
come from a dummynet pipe. Without this, the code which increments
the per-ifaddr stats can dereference an uninitialised pointer. This
should make dummynet usable again.
Reported by: "Dmitry A. Yanko" <fm@astral.ntu-kpi.kiev.ua>
Reviewed by: luigi, joe
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
used for up to "vfs.aio.max_buf_aio" of the requests. If a request
size is MAXPHYS, but the request base isn't page aligned, vmapbuf()
will map the end of the user space buffer into the start of the kva
allocated for the next physical buffer. Don't use a physical buffer
in this case. (This change addresses problem report 25617.)
When an aio_read/write() on a raw device has completed, timeout() is
used to schedule a signal to the process. Thus, the reporting is
delayed up to 10 ms (assuming hz is 100). The process might have
terminated in the meantime, causing a trap 12 when attempting to
deliver the signal. Thus, the timeout must be cancelled when removing
the job.
aio jobs in state JOBST_JOBQGLOBAL should be removed from the
kaio_jobqueue list during process rundown.
During process rundown, some aio jobs might move from one list to a
different list that has already been "emptied", causing the rundown to
be incomplete. Retry the rundown.
A call to BUF_KERNPROC() is needed after obtaining a physical buffer
to disassociate the lock from the running process since it can return
to userland without releasing that lock.
PR: 25617
Submitted by: tegge
Change a prototype.
Add a function version of ng_ref_node() when debugging so
a breakpoint can be set on it.
ng_base.c:
add 'node' as an argument to ng_apply_item so that it is up
to the caller to take over and release the item's reference on
the node. If the release reports back that the node went away
due to the reference going to 0, the caller should cease referencing
the now defunct node. (e.g. the item was a 'kill node' message).
Alter ng_unref_node to report back the residual references as a result.
ng_pptpgre.c:
Don't reference a node after we dropped a reference to it.
(What if it was the last?)
Fixes a node leak reported by Harti Brandt <brandt@fokus.gmd.de>
which was due to an incorrect earlier attempt to fix the
"accessing node after dropping the last reference" problem.
o Separate the kernel stuff from the Yarrow algorithm. Yarrow is now
well contained in one source file and one header.
o Replace the Blowfish-based crypto routines with Rijndael-based ones.
(Rijndael is the new AES algorithm). The huge improvement in
Rijndael's key-agility over Blowfish means that this is an
extremely dramatic improvement in speed, and makes a heck of
a difference in its (lack of) CPU load.
o Clean up the sysctl's. At BDE's prompting, I have gone back to
static sysctls.
o Bug fixes. The streamlining of the crypto stuff enabled me to
find and fix some bugs. DES also found a bug in the reseed routine
which is fixed.
o Change the way reseeds clear "used" entropy. Previously, only the
source(s) that caused a reseed were cleared. Now all sources in the
relevant pool(s) are cleared.
o Code tidy-up. Mostly to make it (nearly) 80-column compliant.
